With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/i2c/uda1342.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
- Conversion of max9286 and adv748x to V4L2 subdev active state
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The adv748x-csi2 driver configures the CSI-2 transmitter to
automatically infer the image stream format from the connected
frontend (HDMI or AFE).
Setting a new format on the subdevice hence does not actually control
the CSI-2 output format, but it's only there for the purpose of
pipeline validation.
However, there is currently no validation that the supplied media bus
code is valid and supported by the device.
With the introduction of enum_mbus_codes a list of supported format is
now available, use it to validate that the supplied format is correct
and use the default UYVY8 one if that's not the case.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240617161135.130719-8-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Rename 'st-vgxy61' to 'vgxy61', dropping the vendor prefix to follow the
same naming scheme as the vast majority of device drivers.
The device tree binding does not fall into binding rename exceptions and
therefore must not be changed. Keep its legacy name.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It was reported to me that the imx219 didn't work on one of our
development kits partly because the access sequence is incorrect.
The datasheet I could find [1] for this camera has the access sequence:
Seq. No. Address (Hex) data
1 30EB 05
2 30EB 0C
3 300A FF
4 300B FF
5 30EB 05
6 30EB 09
but the driver swaps the first two elements. Laurent pointed out on IRC
that the original code used the correct sequence for 1920x1080 but the
current sequence for 3280x2464 and 1640x1232. During refactoring of the
init sequence the current order was used for all formats.
Switch to using the documented sequence.
Link: https://www.opensourceinstruments.com/Electronics/Data/IMX219PQ.pdf [1]
Fixes: 8508455961 ("media: i2c: imx219: Split common registers from mode tables")
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ov2680 driver has 9 controls now and the call to
v4l2_ctrl_new_fwnode_properties() adds 2 more.
Tell v4l2_ctrl_handler_init() to pre-allocate space for 11
controls to match this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Alvium camera by default is in free running mode. Datasheet say that
acquisition frame rate reg can only be used if frame start trigger
mode is set to off.
Enable r/w acquisition frame rate and turn off trigger mode.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
[Sakari Ailus: Fix spelling of "acquisition".]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acquisition frame rate enable reg have a very long name let's reduce this
with an abbreviation.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
[Sakari Ailus: Fix spelling of "acquisition".]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of reading device_fw reg as multiple regs let's read the entire
64bit reg using one i2c read and use bit masks and bit shifts to get fw
info.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Drop privacy-LED GPIO control, after the privacy-LED GPIO control was added
to the ov5693 driver it was decided to model privacy-LEDs as LED class
devices and have them be controlled by the v4l2-core.
So this is dead code since on devices with privacy LEDs the led is not
a GPIO on the ov5693 fwnode, but rather is a LED class devices controlled
by the v4l2-core.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stopping the CSI source before stopping the serializer
CSI port may make the serializer not respond.
Then all the next writes to the device will fail.
max96717 1-0040: Error writing reg 0x0308: -121
max96717 1-0040: Error writing reg 0x0006: -121
Fix that by stopping the CSI receiver first and then CSI source.
Seen on max96717f revision 4.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver handles the MAX96714 deserializer in tunnel mode.
The CSI output will replicate all the CSI traffic forwarded by
the remote serializer.
The MAX96714 driver can handle MAX96714 and MAX96714F variants
with the same "maxim,max96714f" compatible.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
[Sakari Ailus: Adapt to changed i2c_mux_add_adapter arguments.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This driver handles the MAX96717 serializer in tunnel mode.
All incoming CSI traffic will be tunneled through the GMSL2
link.
The MAX96717 driver can handle MAX96717 and MAX96717F variants
with the same "maxim,max96717f" compatible.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
[Sakari Ailus: Adapt to changed i2c_mux_add_adapter arguments.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a v4l2 subdevice driver for the Sony IMX283 image sensor.
The IMX283 is a 20MP Diagonal 15.86 mm (Type 1) CMOS Image Sensor with
Square Pixel for Color Cameras.
The following features are supported:
- Manual exposure an gain control support
- vblank/hblank/link freq control support
- Test pattern support control
- Arbitrary horizontal and vertical cropping
- Supported resolution:
- 5472x3648 @ 20fps (SRGGB12)
- 5472x3648 @ 25fps (SRGGB10)
- 2736x1824 @ 50fps (SRGGB12)
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
[Sakari Ailus: Take upstream runtime PM API changes into account.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The sensor supports H & V flips, but the controls were READ_ONLY.
Note that the Bayer order changes with these flips, therefore
they set the V4L2_CTRL_FLAG_MODIFY_LAYOUT property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Sony have advised that there are variants of the IMX258 sensor which
require slightly different register configuration to the mainline
imx258 driver defaults.
There is no available run-time detection for the variant, so add
configuration via the DT compatible string.
The Vision Components imx258 module supports PDAF, so add the
register differences for that variant
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With the binned modes, there is little point in faithfully
reproducing the horizontal line length of 5352 pixels on the CSI2
bus, and the FIFO between the pixel array and MIPI serialiser
allows us to remove that dependency.
Allow the pixel array to run with the normal settings, with the MIPI
serialiser at half the rate. This requires some additional
information for the link frequency to pixel rate function that
needs to be added to the configuration tables.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
V4L2 sensor drivers are expected to clip the supported exposure
range based on the VBLANK configured.
IMX258 wasn't doing that as register 0x350 (FRM_LENGTH_CTL)
switches it to a mode where frame length tracks coarse exposure time.
Disable this mode and clip the range for V4L2_CID_EXPOSURE appropriately
based on V4L2_CID_VBLANK.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There's no reason why only a clock of 19.2MHz is supported.
Indeed this isn't even a frequency listed in the datasheet.
Add support for 24MHz as well.
The PLL settings result in slightly different link frequencies,
so parameterise those.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The values and ranges of V4L2_CID_VBLANK are all computed,
so there is no reason for it to be a read only control.
Remove the register values from the mode lists, add the
handler, and remove the read only flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
