Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that this combo phy supports
both UTMI+ (HS) and PIPE3 (SS). It also supports DP alt mode.
The number of ports for UTMI+ and PIPE3 can be determined using the
LINKPORT register (which also exists on Exynos E850).
For SuperSpeed (SS) a new SS phy is in use and its PIPE3 interface is
new compared to Exynos E850, and also very different from the existing
support for older Exynos SoCs in this driver.
The SS phy needs a bit more configuration work and register tuning for
signal quality to work reliably, presumably due to the higher
frequency, e.g. to account for different board layouts. Additionally,
power needs to be enabled before writing to the SS phy registers.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-6-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the regulator_bulk APIs, the handling of power supplies becomes
much simpler. There is no need anymore to check if regulators have been
acquired or not, the bulk APIs will do all the work for us. We can also
drop the various handles to the individual power supplies in the driver
runtime data and instead simply treat them all as one thing. Error
cleanup also becomes much simpler.
Converting to the regulator_bulk APIs also makes it easier to add
support for those SoCs that have additional power supplies for the PHY.
Google Tensor gs101 is one example of such a SoC. Otherwise we'd have
to add all additional supplies individually via individual calls to
regulator_get() and enable/disable handle them all individually,
including complicated error handling. That doesn't scale and clutters
the code.
Just update the code to use the regulator_bulk APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-5-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the clk_bulk APIs, the clock handling for the core clocks becomes
much simpler. No need to check any flags whether or not certain clocks
exist or not. Further, we can drop the various handles to the
individual clocks in the driver data and instead simply treat them all
as one thing.
So far, this driver assumes that all platforms have a clock "ref". It
also assumes that the clocks "phy_pipe", "phy_utmi", and "itp" exist if
the platform data "has_common_clk_gate" is set to true. It then goes
and individually tries to acquire and enable and disable all the
individual clocks one by one. Rather than relying on these implicit
clocks and open-coding the clock handling, we can just explicitly spell
out the clock names in the different device data and use that
information to populate clk_bulk_data, allowing us to use the clk_bulk
APIs for managing the clocks.
As a side-effect, this change highlighted the fact that
exynos5_usbdrd_phy_power_on() forgot to check the result of the clock
enable calls. Using the clk_bulk APIs, the compiler now warns when
return values are not checked - therefore add the necessary check
instead of silently ignoring failures and continuing as if all is OK
when it isn't.
For consistency, also change a related dev_err() to dev_err_probe() in
exynos5_usbdrd_phy_clk_handle() to get consistent error message
formatting.
Finally, exynos5_usbdrd_phy_clk_handle() prints an error message in all
cases as necessary (except for -ENOMEM). There is no need to print
another message in its caller (the probe() function), and printing
errors during OOM conditions is usually discouraged. Drop the
duplicated message in exynos5_usbdrd_phy_probe().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-3-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some versions of this IP have been integrated using separate PMU power
control registers for the HS and SS parts. One example is the Google
Tensor gs101 SoC.
Such SoCs can now set pmu_offset_usbdrd0_phy_ss in their
exynos5_usbdrd_phy_drvdata for the SS phy to the appropriate value.
The existing 'usbdrdphy' alias can not be used in this case because
that is meant for determining the correct PMU offset if multiple
distinct PHYs exist in the system (as opposed to one PHY with multiple
isolators).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-2-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While commit 255ec3879d ("phy: exynos5-usbdrd: Add 26MHz ref clk
support") correctly states that CLKRSTCTRL[7:5] doesn't need to be set
on modern Exynos platforms, SSPPLLCTL[2:0] should be programmed with
the frequency of the reference clock for the USB2.0 phy instead.
I stumbled across this while adding support for the Google Tensor
gs101, but this should apply to E850 just the same.
Do so.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-5-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using 0x82 seems odd, where everything else is just a sequence.
On E850, this macro isn't used (as a register value), only to assign
its value to the 'extrefclk' variable, which is otherwise unused on
that platform. Older platforms don't appear to support 26MHz in the
first place (since this macro was added for E850).
Furthermore, the downstream driver uses 0x82 to denote
USBPHY_REFCLK_DIFF_26MHZ (whatever that means exactly), but for all the
other values we match downstream's non-DIFF macros.
Update to avoid confusion. No functional change intended.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-4-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The timers-howto recommends using usleep_range() and friends anytime
waiting for >= ~10us is required. Doing so can help the timer subsystem
a lot to coalesce wakeups.
Additionally, fsleep() exists as a convenient wrapper so we do not have
to think about which exact sleeping function is required in which case.
Convert all udelay() calls in this driver to use fsleep() to follow the
recommendataion.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-2-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Most of the macros are ordered high -> low, but there are some
outliers.
Order them all uniformly from high to low. This will allow adding
additional register (field) definitions in a consistent way.
While at it, also remove some extra empty lines to group register bit
field definitions together with the relevant register. This makes the
registers easier to distinguish visually.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240507-samsung-usb-phy-fixes-v1-1-4ccba5afa7cc@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement Exynos850 USB 2.0 DRD PHY controller support. Exynos850 has
quite a different PHY controller than Exynos5 compatible controllers,
but it's still possible to implement it on top of existing
exynos5-usbdrd driver infrastructure.
Only UTMI+ (USB 2.0) PHY interface is implemented, as Exynos850 doesn't
support USB 3.0.
Only two clocks are used for this controller:
- phy: bus clock, used for PHY registers access
- ref: PHY reference clock (OSCCLK)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-7-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Modern Exynos chips (like Exynos850) might have 26 MHz OSCCLK external
clock, which is also used as a PHY reference clock. For some USB PHY
controllers (e.g USB DRD PHY block on Exynos850) there is no need to set
the refclk frequency at all (and corresponding bits in CLKRSTCTRL[7:5]
are marked RESERVED), so that value won't be set in the driver. But
even in that case, 26 MHz support still has to be added, otherwise
exynos5_rate_to_clk() fails, which leads in turn to probe error.
Add the correct value for 26MHz refclk to make it possible to add
support for new Exynos USB DRD PHY controllers.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-6-semen.protsenko@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Consolidate duplicated 'next function' scanning and extend to allow
'isolated functions' on s390, similar to existing hypervisors
(Niklas Schnelle)
Resource management:
- Implement pci_iobar_pfn() for sparc, which allows us to remove the
sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().
This removes the ability to map the entire PCI I/O space using
/proc/bus/pci, but we believe that's already been broken since
v2.6.28 (Arnd Bergmann)
- Move common PCI definitions to asm-generic/pci.h and rework others
to be be more specific and more encapsulated in arches that need
them (Stafford Horne)
Power management:
- Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)
Virtualization:
- Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
the functions but don't advertise an ACS capability (Pavan Chebbi)
Error handling:
- Clear PCI Status register during enumeration in case firmware left
errors logged (Kai-Heng Feng)
- When we have native control of AER, enable error reporting for all
devices that support AER. Previously only a few drivers enabled
this (Stefan Roese)
- Keep AER error reporting enabled for switches. Previously we
enabled this during enumeration but immediately disabled it (Stefan
Roese)
- Iterate over error counters instead of error strings to avoid
printing junk in AER sysfs counters (Mohamed Khalfella)
ASPM:
- Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
via sysfs, are not lost across power state changes (Kai-Heng Feng)
Endpoint framework:
- Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)
Endpoint embedded DMA controller driver:
- Simplify and clean up support for the DesignWare embedded DMA
(eDMA) controller (Frank Li, Serge Semin)
Broadcom STB PCIe controller driver:
- Avoid config space accesses when link is down because we can't
recover from the CPU aborts these cause (Jim Quinlan)
- Look for power regulators described under Root Ports in DT and
enable them before scanning the secondary bus (Jim Quinlan)
- Disable/enable regulators in suspend/resume (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Simplify and clean up clock and PHY management (Richard Zhu)
- Disable/enable regulators in suspend/resume (Richard Zhu)
- Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)
- Allow speeds faster than Gen2 (Richard Zhu)
- Make link being down a non-fatal error so controller probe doesn't
fail if there are no Endpoints connected (Richard Zhu)
Loongson PCIe controller driver:
- Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)
- Avoid config reads to non-existent LS2K/LS7A devices because a
hardware defect causes machine hangs (Huacai Chen)
- Work around LS7A integrated devices that report incorrect Interrupt
Pin values (Jianmin Lv)
Marvell Aardvark PCIe controller driver:
- Add support for AER and Slot capability on emulated bridge (Pali
Rohár)
MediaTek PCIe controller driver:
- Add Airoha EN7532 to DT binding (John Crispin)
- Allow building of driver for ARCH_AIROHA (Felix Fietkau)
MediaTek PCIe Gen3 controller driver:
- Print decoded LTSSM state when the link doesn't come up (Jianjun
Wang)
NVIDIA Tegra194 PCIe controller driver:
- Convert DT binding to json-schema (Vidya Sagar)
- Add DT bindings and driver support for Tegra234 Root Port and
Endpoint mode (Vidya Sagar)
- Fix some Root Port interrupt handling issues (Vidya Sagar)
- Set default Max Payload Size to 256 bytes (Vidya Sagar)
- Fix Data Link Feature capability programming (Vidya Sagar)
- Extend Endpoint mode support to devices beyond Controller-5 (Vidya
Sagar)
Qualcomm PCIe controller driver:
- Rework clock, reset, PHY power-on ordering to avoid hangs and
improve consistency (Robert Marko, Christian Marangi)
- Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)
- Add IPQ60xx support (Selvam Sathappan Periakaruppan)
- Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)
- Add support for more than 32 MSI interrupts (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Convert DT binding to json-schema (Herve Codina)
- Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
(Herve Codina)
Samsung Exynos PCIe controller driver:
- Fix phy-exynos-pcie driver so it follows the 'phy_init() before
phy_power_on()' PHY programming model (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Simplify and clean up the DWC core extensively (Serge Semin)
- Fix an issue with programming the ATU for regions that cross a 4GB
boundary (Serge Semin)
- Enable the CDM check if 'snps,enable-cdm-check' exists; previously
we skipped it if 'num-lanes' was absent (Serge Semin)
- Allocate a 32-bit DMA-able page to be MSI target instead of using a
driver data structure that may not be addressable with 32-bit
address (Will McVicker)
- Add DWC core support for more than 32 MSI interrupts (Dmitry
Baryshkov)
Xilinx Versal CPM PCIe controller driver:
- Add DT binding and driver support for Versal CPM5 Gen5 Root Port
(Bharat Kumar Gogada)"
* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
PCI: imx6: Support more than Gen2 speed link mode
PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
PCI: imx6: Reformat suspend callback to keep symmetric with resume
PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
PCI: imx6: Disable clocks in reverse order of enable
PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
PCI: imx6: Reduce resume time by only starting link if it was up before suspend
PCI: imx6: Mark the link down as non-fatal error
PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
PCI: imx6: Turn off regulator when system is in suspend mode
PCI: imx6: Call host init function directly in resume
PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
PCI: imx6: Propagate .host_init() errors to caller
PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
PCI: imx6: Factor out ref clock disable to match enable
PCI: imx6: Move imx6_pcie_clk_disable() earlier
PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
PCI: imx6: Move PHY management functions together
PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
...
The exynos-pcie driver called phy_power_on() before phy_init() for some
historical reasons. However the generic PHY framework assumes that the
proper sequence is to call phy_init() first, then phy_power_on(). The
operations done by both functions should be considered as one action and as
such they are called by the exynos-pcie driver (without doing anything
between them). The initialization is just a sequence of register writes,
which cannot be altered without breaking the hardware operation.
To match the generic PHY framework requirement, simply move all register
writes to the phy_init()/phy_exit() and drop power_on()/power_off()
callbacks. This way the driver will also work with the old (incorrect)
PHY initialization call sequence.
Link: https://lore.kernel.org/r/20220628220409.26545-1-m.szyprowski@samsung.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Exynos5420 variant of USB2 PHY is handled by the same code as the
Exynos5250 one. Introducing a separate Kconfig symbol for it was an
over-engineering, which turned out to cause build break for certain
configurations:
ERROR: modpost: "exynos5420_usb2_phy_config" [drivers/phy/samsung/phy-exynos-usb2.ko] undefined!
Fix this by removing PHY_EXYNOS5420_USB2 symbol and using
PHY_EXYNOS5250_USB2 also for Exynos5420 SoCs.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Fixes: 81b534f7e9 ("phy: samsung: Add support for the Exynos5420 variant of the USB2 PHY")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20201202064759.24300-1-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Exynos5420 differs a bit from Exynos5250 in USB2 PHY related registers in
the PMU region. Add a variant for the Exynos5420 case. Till now, USB2 PHY
worked only because the bootloader enabled the PHY, but then driver messed
USB 3.0 DRD related registers during the suspend/resume cycle.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120085637.7299-2-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of a busy waiting while loop using udelay
use readl_poll_timeout function to check the condition
is met or timeout occurs in crport_handshake function.
readl_poll_timeout is called in non atomic context so
it safe to sleep until the condition is met.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Link: https://lore.kernel.org/r/20200720173502.542-1-linux.amoon@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
