Wa_15015404425 asks us to perform four "dummy" writes to a
non-existent register offset before every real register read.
Although the specific offset of the writes doesn't directly
matter, the workaround suggests offset 0x130030 as a good target
so that these writes will be easy to recognize and filter out in
debugging traces.
V5(MattR):
- Avoid negating an equality comparison
V4(MattR):
- Use writel and remove xe_reg usage
V3(MattR):
- Define dummy reg local to function
- Avoid tracing dummy writes
- Update commit message
V2:
- Add WA to 8/16/32bit reads also - MattR
- Corrected dummy reg address - MattR
- Use for loop to avoid mental pause - JaniN
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240709155606.2998941-1-tejas.upadhyay@intel.com
(cherry picked from commit 86c5b70a9c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We recently moved the teardown of the vgic part of a vcpu inside
a critical section guarded by the config_lock. This teardown phase
involves calling into kvm_io_bus_unregister_dev(), which takes the
kvm->srcu lock.
However, this violates the established order where kvm->srcu is
taken on a memory fault (such as an MMIO access), possibly
followed by taking the config_lock if the GIC emulation requires
mutual exclusion from the other vcpus.
It therefore results in a bad lockdep splat, as reported by Zenghui.
Fix this by moving the call to kvm_io_bus_unregister_dev() outside
of the config_lock critical section. At this stage, there shouln't
be any need to hold the config_lock.
As an additional bonus, document the ordering between kvm->slots_lock,
kvm->srcu and kvm->arch.config_lock so that I cannot pretend I didn't
know about those anymore.
Fixes: 9eb18136af ("KVM: arm64: vgic: Hold config_lock while tearing down a CPU interface")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240819125045.3474845-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Pull printk fix from Petr Mladek:
- Do not block printk on non-panic CPUs when they are dumping
backtraces
* tag 'printk-for-6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk/panic: Allow cpu backtraces to be written into ringbuffer during panic
These new trace points record xarray indices and the time of
endpoint registration and unregistration, to co-ordinate with
device removal events.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Nit: The built-in xa_limit_32b range starts at 0, but
XA_FLAGS_ALLOC1 configures the xarray's allocator to start at 1.
Adopt the more conventional XA_FLAGS_ALLOC because there's no
mechanical reason to skip 0.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If the device's reference count is too high, the device completion
callback never fires.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Its possible that two threads call tcp_sk_exit_batch() concurrently,
once from the cleanup_net workqueue, once from a task that failed to clone
a new netns. In the latter case, error unwinding calls the exit handlers
in reverse order for the 'failed' netns.
tcp_sk_exit_batch() calls tcp_twsk_purge().
Problem is that since commit b099ce2602 ("net: Batch inet_twsk_purge"),
this function picks up twsk in any dying netns, not just the one passed
in via exit_batch list.
This means that the error unwind of setup_net() can "steal" and destroy
timewait sockets belonging to the exiting netns.
This allows the netns exit worker to proceed to call
WARN_ON_ONCE(!refcount_dec_and_test(&net->ipv4.tcp_death_row.tw_refcount));
without the expected 1 -> 0 transition, which then splats.
At same time, error unwind path that is also running inet_twsk_purge()
will splat as well:
WARNING: .. at lib/refcount.c:31 refcount_warn_saturate+0x1ed/0x210
...
refcount_dec include/linux/refcount.h:351 [inline]
inet_twsk_kill+0x758/0x9c0 net/ipv4/inet_timewait_sock.c:70
inet_twsk_deschedule_put net/ipv4/inet_timewait_sock.c:221
inet_twsk_purge+0x725/0x890 net/ipv4/inet_timewait_sock.c:304
tcp_sk_exit_batch+0x1c/0x170 net/ipv4/tcp_ipv4.c:3522
ops_exit_list+0x128/0x180 net/core/net_namespace.c:178
setup_net+0x714/0xb40 net/core/net_namespace.c:375
copy_net_ns+0x2f0/0x670 net/core/net_namespace.c:508
create_new_namespaces+0x3ea/0xb10 kernel/nsproxy.c:110
... because refcount_dec() of tw_refcount unexpectedly dropped to 0.
This doesn't seem like an actual bug (no tw sockets got lost and I don't
see a use-after-free) but as erroneous trigger of debug check.
Add a mutex to force strict ordering: the task that calls tcp_twsk_purge()
blocks other task from doing final _dec_and_test before mutex-owner has
removed all tw sockets of dying netns.
Fixes: e9bd0cca09 ("tcp: Don't allocate tcp_death_row outside of struct netns_ipv4.")
Reported-by: syzbot+8ea26396ff85d23a8929@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/0000000000003a5292061f5e4e19@google.com/
Link: https://lore.kernel.org/netdev/20240812140104.GA21559@breakpoint.cc/
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240812222857.29837-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with gcc-5:
In function ‘decode_oa_format.isra.26’,
inlined from ‘xe_oa_set_prop_oa_format’ at drivers/gpu/drm/xe/xe_oa.c:1664:6:
././include/linux/compiler_types.h:510:38: error: call to ‘__compiletime_assert_1336’ declared with attribute error: FIELD_GET: mask is not constant
[...]
./include/linux/bitfield.h:155:3: note: in expansion of macro ‘__BF_FIELD_CHECK’
__BF_FIELD_CHECK(_mask, _reg, 0U, "FIELD_GET: "); \
^
drivers/gpu/drm/xe/xe_oa.c:1573:18: note: in expansion of macro ‘FIELD_GET’
u32 bc_report = FIELD_GET(DRM_XE_OA_FORMAT_MASK_BC_REPORT, fmt);
^
Fixes: b6fd51c621 ("drm/xe/oa/uapi: Define and parse OA stream properties")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729092634.2227611-1-geert+renesas@glider.be
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit f2881dfdaa)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Dell All In One (AIO) models released after 2017 may use a backlight
controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
The Dell OptiPlex 7760 AIO has an ACPI device for one if its UARTs with
the above _HID + _CID. Loading the dell-uart-backlight driver shows that
there actually is a backlight controller board attached to the UART,
which reports a firmware version of "G&MX01-V15".
But the backlight controller board does not actually control the backlight
brightness and the GPU's native backlight control method does work.
Add a quirk to use the GPU's native backlight control method on this model.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2303936
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-4-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dell-uart-backlight driver supports backlight control on Dell All In
One (AIO) models using a backlight controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
Now the first AIO has turned up which has not only the DSDT bits for this,
but also an actual controller attached to the UART, yet it is not using
this controller for backlight control.
Use the acpi_video_get_backlight_type() function from the ACPI video-detect
code to check if the dell-uart-backlight driver should actually be used.
This allows reusing the existing ACPI video-detect infra to override
the backlight control method on the commandline or with DMI quirks.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-3-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dell All In One (AIO) models released after 2017 use a backlight
controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
Commit 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
has added support for this, but I neglected to tie this into
acpi_video_get_backlight_type().
Now the first AIO has turned up which has not only the DSDT bits for this,
but also an actual controller attached to the UART, yet it is not using
this controller for backlight control.
Add support to acpi_video_get_backlight_type() for a new dell_uart
backlight type. So that the existing infra to override the backlight
control method on the commandline or with DMI quirks can be used.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20240814190159.15650-2-hdegoede@redhat.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hangbin Liu says:
====================
selftests: Fix udpgro failures
There are 2 issues for the current udpgro test. The first one is the testing
doesn't record all the failures, which may report pass but the test actually
failed. e.g.
https://netdev-3.bots.linux.dev/vmksft-net/results/725661/45-udpgro-sh/stdout
The other one is after commit d7db7775ea ("net: veth: do not manipulate
GRO when using XDP"), there is no need to load xdp program to enable GRO
on veth device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit d7db7775ea ("net: veth: do not manipulate GRO when using
XDP"), there is no need to load XDP program to enable GRO. On the other
hand, the current test is failed due to loading the XDP program. e.g.
# selftests: net: udpgro.sh
# ipv4
# no GRO ok
# no GRO chk cmsg ok
# GRO ./udpgso_bench_rx: recv: bad packet len, got 1472, expected 14720
#
# failed
[...]
# bad GRO lookup ok
# multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
#
# failed
ok 1 selftests: net: udpgro.sh
After fix, all the test passed.
# ./udpgro.sh
ipv4
no GRO ok
[...]
multiple GRO socks ok
Fixes: d7db7775ea ("net: veth: do not manipulate GRO when using XDP")
Reported-by: Yi Chen <yiche@redhat.com>
Closes: https://issues.redhat.com/browse/RHEL-53858
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only check the latest senders's exit code. If the receiver
report failed, it is not recoreded. Fix it by checking the exit code
of all the involved processes.
Before:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
0
After:
bad GRO lookup ok
multiple GRO socks ./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
./udpgso_bench_rx: recv: bad packet len, got 1452, expected 14520
failed
$ echo $?
1
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the WCN module is powered up before linux boots and the ath11k driver
probes at the same time as the power sequencing driver, we may end up
driving the wlan-enable GPIO low in the latter, breaking the start-up of
the WLAN module. Request the wlan-enable GPIO as-is so that if the WLAN
module is already starting/started, we leave it alone.
Fixes: 2f1630f437 ("power: pwrseq: add a driver for the PMU module on the QCom WCN chipsets")
Reported-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20240813190751.155035-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
On s3 resume the i8042 driver tries to restore the controller to a known
state by reinitializing things, however this can confuse the controller
with different effects. Mostly occasionally unresponsive keyboards after
resume.
These issues do not rise on s0ix resume as here the controller is assumed
to preserved its state from before suspend.
This patch adds a quirk for devices where the reinitialization on s3 resume
is not needed and might be harmful as described above. It does this by
using the s0ix resume code path at selected locations.
This new quirk goes beyond what the preexisting reset=never quirk does,
which only skips some reinitialization steps.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240104183118.779778-2-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are checking cp_irq_count from the wrong hdcp structure which
ends up giving timed out errors. We only increment the cp_irq_count
of the primary connector's hdcp structure but here in case of
multidisplay setup we end up checking the secondary connector's hdcp
structure, which will not have its cp_irq_count incremented. This leads
to a timed out at CP_IRQ error even though a CP_IRQ was raised. Extract
it from the correct intel_hdcp structure.
--v2
-Explain why it was the wrong hdcp structure [Jani]
Fixes: 8c9e4f68b8 ("drm/i915/hdcp: Use per-device debugs")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809114127.3940699-2-suraj.kandpal@intel.com
(cherry picked from commit dd92590263)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If there is ->PreviousSessionId field in the session setup request,
The session of the previous connection should be destroyed.
During this, if the smb2 operation requests in the previous session are
being processed, a racy issue could happen with ksmbd_destroy_file_table().
This patch sets conn->status to KSMBD_SESS_NEED_RECONNECT to block
incoming operations and waits until on-going operations are complete
(i.e. idle) before desctorying the previous session.
Fixes: c8efcc7861 ("ksmbd: add support for durable handles v1/v2")
Cc: stable@vger.kernel.org # v6.6+
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-25040
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
rsp buffer is allocated larger than spnego_blob from
smb2_allocate_rsp_buf().
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Mandatory locking is enforced for cached reads, which violates
default posix semantics, and also it is enforced inconsistently.
This affected recent versions of libreoffice, and can be
demonstrated by opening a file twice from the same client,
locking it from handle one and trying to read from it from
handle two (which fails, returning EACCES).
There is already a mount option "forcemandatorylock"
(which defaults to off), so with this change only when the user
intentionally specifies "forcemandatorylock" on mount will we
break posix semantics on read to a locked range (ie we will
only fail in this case, if the user mounts with
"forcemandatorylock").
An earlier patch fixed the write path.
Fixes: 85160e03a7 ("CIFS: Implement caching mechanism for mandatory brlocks")
Cc: stable@vger.kernel.org
Cc: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Reported-by: abartlet@samba.org
Reported-by: Kevin Ottens <kevin.ottens@enioka.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
