This patch adds a save and restore mechanism for ARM L2 auxiliary control
register. The feature is enabled by default for GP devices, but for HS/EMU
devices the user must enable the service and define the PPA service ID to
be used for setting L2 aux ctrl, as this is not currently supported by the
bootloader. If nobody alters the contents of L2 aux ctrl from its reset
value, this feature is not needed.
Kconfig option to enable HS/EMU L2 aux save and restore:
- OMAP3_L2_AUX_SECURE_SAVE_RESTORE
Kconfig option to select HS/EMU PPA service for setting L2 aux ctrl:
- OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch implements locking using the semaphore in scratchpad
memory preventing any concurrent access to scratchpad from OMAP
and Baseband/Modem processor.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pass cpuidle parameters for RX-51. Numbers based on
measurements made in October 2009 for PM optimized
kernel with CPU freq enabled. Assumes OPP2 (main
idle OPP, and worst case latencies).
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The sleep indicator LEDs can be enabled/disabled by toggling GPIO162.
Use the LED GPIO class to export this LED functionality to userspace.
To enable:
# echo 1 > /sys/class/leds/sleep_ind/brightness
To disable:
# echo 0 > /sys/class/leds/sleep_ind/brightness
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Different boards benefit differently from the available
seven C-states for cpu idle. In most cases, only few,
properly spaced (in terms of consumption and latency)
C-states are required to make the power management
optimal. Hence we need a possibility to pass which
C-states are actually used for each board.
So added the valid field to cpuidle_params and added
support to 3430sdp, which uses the paramenter passing.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPUidle C state latencies and thresholds are dependent on various
board specific details. This patch makes it possible to configure
these values from the respective board files.
omap3_pm_init_cpuidle() can now be optionally called from board files
to pass board specific cpuidle parameters. If the board files do not
use this function to pass the params default values are used which
might cause higher consumption dur to wrong state selection by the
governor.
This patch only updates the 3430sdp board files to use
omap3_pm_init_cpuidle().
From Kalle, in addition to original patch from Rajendra:
Building without CONFIG_CPU_IDLE or CONFIG_PM causes build to fail if
cpu idle parameters are tried to pass using omap3_pm_init_cpuidle
function.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When 'enable_off_mode' is 0, the target power state for MPU
and CORE was locally changed to PWRDM_POWER_RET but, the
statistics are updated for idle state originally selected
by the governor.
This patch 'invalidates' the idle states that lead either of
MPU or Core to PWRDM_POWER_OFF state when 'enable_off_mode'
is '0'. The states are valid once 'enable_off_mode' is set
to '1'.
Added function next_valid_state() to check if current state
is valid; else get the next valid state. It is called from
omap3_enter_idle_bm().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes the L4 wakeup io mapping section for omap3
and omap4. L4 wakeup space is part of 4MB L4 space which is
already mapped and hence remove the overlapped mapping.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 'ba50ea7e' reserves DMA channels 0 and 1 on high
security devices, in order to avoid collision between kernel
dma transfers and ROM code dma transfers.
This fix is applicable only for OMAP3 so add an appropriate
check.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is a clean-up patch towards dynamic allocation of IO space
instead of using harcoded macros to calculate virtual addresses.
Also update the sdrc, prcm and control module to allocate
iospace dynamically
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch is addition to the already merged commit on non-empty
uart fifo read abort. "ce13d4716a276f4331d78ba28a5093a63822ab95"
OMAP3630 and OMAP4430 UART IP blocks have a restriction on TX FIFO
too. If you try to write to the tx fifo when it is full, the system aborts.
More details on this thread are here:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg19447.html
This can be easily reproducible by not suppressing interconnect errors or
long duration testing where continuous prints over console from multiple
threads. This patch is addressing the issue by ensuring that write is
not issued while fifo is full. A timeout is added to avoid any hang
on fifo-full for 10 mS which is unlikely case.
Patch is validated on OMAP3630 and OMAP4 SDP.
V2 version removed the additional 1 uS on every TX as per
Tony's suggestion
Signed-off-by: Woodruff Richard <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Ghorai Sukumar <s-ghorai@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The musb support is enabled in omap3 platforms. For omap4 only board
support is available and the driver still isn't supported.
Because of this build with omap3_defconfig used for multi-omap
doesn't work on omap4430 sdp.
This patch avoids usb_musb_init() by adding a cpu check
in the board file.
Thanks to Anand Gadiyar and Mankad Maulik for the suggestion
of patching board file instead of musb driver.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
> FYI, this commit broke tip:master on PARISC (other architectures are fine):
>
> kernel/built-in.o: In function `ptrace_request':
> (.text.ptrace_request+0x2cc): undefined reference to `task_user_regset_view'
This means that parisc failed to meet the documented requirements for
setting CONFIG_HAVE_ARCH_TRACEHOOK, but set it anyway. If arch folks don't
follow the specs, it defeats the whole purpose of having clear statements
of requirements for arch code.
Until parisc finishes up its requirements, disable CONFIG_HAVE_ARCH_TRACEHOOK.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20100222183707.8749D64C@magilla.sf.frob.com>
Cc: <linux-parisc@vger.kernel.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This hooks up the SET/GET_UNALIGN_CTL knobs cribbing the bulk of it from
the PPC and ia64 implementations. The thread flags happen to be the
logical inverse of what the global fault mode is set to, so this works
out pretty cleanly. By default the global fault mode is used, with tasks
now being able to override their own settings via prctl().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge reason:
Conflicts in arch/x86/kernel/apic/io_apic.c
Resolved Conflicts:
arch/x86/kernel/apic/io_apic.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the init.c and time.c files to plat-samsung from plat-s3c, thus
clearing the last files that are being built in here.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the map-base file to plat-samsung. To make the move easier, we do not
change the S3C_ prefix on many of the items as this would involve going
through altering all the dependencies.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move common headers from plat-s3c's include/plat directory into plat-samsung.
No need to fix any files, these are still included via <plat/>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Now we've move the support out of plat-s3c64xx for everything, eliminate
the platform directory arch/arm/plat-s3c64xx and remove it from the ARM
build configuration.
Note, PLAT_S3C64XX is kept around for the moment until the drivers that
depend on it can be updated, so it is moved to the mach-s3c64xx Kconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We currently enforce the !RW mapping for the kernel mapping that maps
holes between different text, rodata and data sections. However, kernel
identity mappings will have different RWX permissions to the pages mapping to
text and to the pages padding (which are freed) the text, rodata sections.
Hence kernel identity mappings will be broken to smaller pages. For 64-bit,
kernel text and kernel identity mappings are different, so we can enable
protection checks that come with CONFIG_DEBUG_RODATA, as well as retain 2MB
large page mappings for kernel text.
Konrad reported a boot failure with the Linux Xen paravirt guest because of
this. In this paravirt guest case, the kernel text mapping and the kernel
identity mapping share the same page-table pages. Thus forcing the !RW mapping
for some of the kernel mappings also cause the kernel identity mappings to be
read-only resulting in the boot failure. Linux Xen paravirt guest also
uses 4k mappings and don't use 2M mapping.
Fix this issue and retain large page performance advantage for native kernels
by not working hard and not enforcing !RW for the kernel text mapping,
if the current mapping is already using small page mapping.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1266522700.2909.34.camel@sbs-t61.sc.intel.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/mips/mm/highmem.c: In function 'kmap_init':
arch/mips/mm/highmem.c:130: error: 'init_mm' undeclared (first use in this function)
arch/mips/mm/highmem.c:130: error: (Each undeclared identifier is reported only once
arch/mips/mm/highmem.c:130: error: for each function it appears in.)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 81bf550d9c.
HAVE_ARCH_TRACEHOOK requires defining the user_regset interfaces,
including task_user_regset_view(). parisc doesn't do that yet,
so don't lie about it.
Signed-off-by: Roland McGrath <roland@redhat.com>
When FSI and Network (= NFS file system) were used at the same time,
the I/O of FSI was unstable. This patch updates the SPU2 clock (which
is used for FSI) to solve this issue. Special thanks to Jeremy.
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 processor code to always enable vpu_clk.
On the Ecovec board, set the vpu_clk to 166 Mhz.
The 166MHz setting results in a divide-by-6 setup for
vpu_clk and improves the VPU performance compared to the
power-on-reset/bootloader configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a ->kick() callback to clk_div4_table
and ties it into sh_clk_div4_set_rate(). A sh7724
specific kick function is also added that updates the
KICK bit whenever div4 clocks in FRQCRA and FRQCRB
have been set. Allows us to set the VPU clock.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces struct clk_div4_table. The structure
will be used to keep div4 specific data, and is with this
patch replacing the struct clk_div_mult_table pointer arg
used by the sh_clk_div4_register() functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
