* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Move cpu hotplug driver lock from pseries to powerpc
powerpc: Move /proc/ppc64 to /proc/powerpc update
powerpc/8xx: Fix user space TLB walk in dcbX fixup
powerpc: Fix decrementer setup on 1GHz boards
powerpc/iseries: Initialise on-stack completion
powerpc/hvc: Driver build breaks with !HVC_CONSOLE
serial/pmac_zilog: Workaround problem due to interrupt on closed port
powerpc/macintosh: Make Open Firmware device id constant
powerpc: Use helpers for rlimits
powerpc: cpumask_of_node() should handle -1 as a node
powerpc/pseries: Fix dlpar compile warning without CONFIG_PROC_DEVICETREE
powerpc/pseries: Fix xics interrupt affinity
powerpc/swsusp_32: Fix TLB invalidation
powerpc/8xx: Always pin kernel instruction TLB
powerpc: 2.6.33 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
powerpc/5200: update defconfigs
For x86-64, 32767 threads really is not enough. Change rwsem_count_t
to a signed long, so that it is 64 bits on x86-64.
This required the following changes to the assembly code:
a) %z0 doesn't work on all versions of gcc! At least gcc 4.4.2 as
shipped with Fedora 12 emits "ll" not "q" for 64 bits, even for
integer operands. Newer gccs apparently do this correctly, but
avoid this problem by using the _ASM_ macros instead of %z.
b) 64 bits immediates are only allowed in "movq $imm,%reg"
constructs... no others. Change some of the constraints to "e",
and fix the one case where we would have had to use an invalid
immediate -- in that case, we only care about the upper half
anyway, so just access the upper half.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <tip-bafaecd11df15ad5b1e598adc7736afcd38ee13d@git.kernel.org>
After talking to some more folks inside intel (Peter Anvin, Asit Mallick),
the safest option (for future compatibility etc) seen was to use vector 0x20
for IRQ_MOVE_CLEANUP_VECTOR instead of using vector 0x1f (which is documented as
reserved vector in the Intel IA32 manuals).
Also we don't need to reserve the entire privilege level (all 16 vectors in
the priority bucket that IRQ_MOVE_CLEANUP_VECTOR falls into), as the
x86 architecture (section 10.9.3 in SDM Vol3a) specifies that with in the
priority level, the higher the vector number the higher the priority.
And hence we don't need to reserve the complete priority level 0x20-0x2f for
the IRQ migration cleanup logic.
So change the IRQ_MOVE_CLEANUP_VECTOR to 0x20 and allow 0x21-0x2f to be used
for device interrupts. 0x30-0x3f will be used for ISA interrupts (these
also can be migrated in the context of IOAPIC and hence need to be at a higher
priority level than IRQ_MOVE_CLEANUP_VECTOR).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100114002118.521826763@sbs-t61.sc.intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This reverts commit 14f0aa3593.
That commit was needed earlier because system call restarting for
OABI (compat) required an executable stack and thus had problems
with NX. Since ab72b00734 ("ARM: Fix signal restart issues
with NX and OABI compat") has reworked the code to not require an
executable stack anymore, we can re-enable NX support for kernels
with OABI (compat) support.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mem_init_done test makes sure that this path is only entered in
__init cases, so leaving ioremap_fixed() as __init and flagging the
caller __init_refok is sufficient.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Because of the include of the decompress_inflate.c file from
boot/compress/misc.c, there are different flush() defines:
In file included from arch/arm/boot/compressed/misc.c:249:
arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:138:29: error: macro "flush" passed 2 arguments, but takes just 0
Fix this by removing the define of flush() in misc.c for
CONFIG_DEBUG_ICEDCC as it's already defined in mach/uncompress.h,
and that is being included unconditionally.
Also use a static inline function instead of define
for mach-mxc and mach-gemini to avoid similar bug
for those platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iounmap() should balance whatever is done by ioremap(). Presently
ioremap() can do any of fixed mappings, PMB mappings, or page table
mappings. Presently only the latter two are handled through the standard
unmap path, so tie in the fixed unmapping, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts iounmap_fixed() to return success/error if it handled the
unmap request or not. At the same time, drop the __init label, as this
can be called in to later.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is nothing of interest in the _64 version anymore, so the _32 one
can be renamed and used unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the fixed ioremap API is only defined when CONFIG_IOREMAP_FIXED
is set. As we want to call in to it unconditionally, provide a stubbed
out interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in a mem_init_done to work out when a standard ioremap() is
possible, falling back to the fixmap based ioremap otherwise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the cpu_relax() to a udelay(1), which fixes up issues with
the EEPROM polling occasionally timing out.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tosses in a local_irq_enable()/disable() pair around the init_fpu()
callsite in the FPU state restore exception handler. Fixes up a slab BUG
triggered by making a slab cache allocation that can sleep whilst
irqs_disabled(). This follows the behaviour undertaken by the x86
implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
More and more boards are going to start shipping that boot with the MMU
in 32BIT mode by default. Previously we relied on the bootloader to
setup PMB mappings for use by the kernel but we also need to cater for
boards whose bootloaders don't set them up.
If CONFIG_PMB_LEGACY is not enabled we have full control over our PMB
mappings and can compress our address space. Usually, the distance
between the the cached and uncached mappings of RAM is always 512MB,
however we can compress the distance to be the amount of RAM on the
board.
pmb_init() now becomes much simpler. It no longer has to calculate any
mappings, it just has to synchronise the software PMB table with the
hardware.
Tested on SDK7786 and SH7785LCR.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Platform devices for SPI Controller of S3C64XX are defined and exported for
machines to include. Also, controller setup helper functions are defined for
machine code to set runtime configuration of the controller and the bus.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We need a way to pass controller specific information to the SPI driver.
For that purpose new headers are made.
SPI Controller is assumed 'type-s3c64xx' and can be defined for newer SoCs.
Hence, that part is placed under plat-samsung to be shared across newer SoCs.
SoC specific part - spi source clocks, will be placed
under plat-<soc>/include/plat/
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The call has been assuming all clksrc-clks' divider size is 4 bits, but
this may not be the case anymore. Use the reg_div.size parameter to
calculate the maximum value it can take and check against that.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The WARN_ON() was only checking the first clock in the array, instead of
being executed for each clksrc clock being registered.
Since this is an array of clocks, WARN_ON() does not provide a lot of
useful information about the problem, so change to using printk(KERN_ERR)
to report the problem to the console.
As a note, we still try and register the clock even if these problems are
present just in case and to avoid changing the behaviour of the registration
process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Adds a additional check in s3c_set_clksrc function to ensure that the clksrc_clk
does have a choice of multiple clock sources. In addition to this, a check is
added to ensure that a parent is assigned to the clksrc_clk in case it does not
have a choice of parent clocks.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_hd0 and clk_pd0 where given a local dummy_enable call due to
not being registered with the clock code, which they really should have
been. Register these two clocks and remove the clk_dummy_enable as this
is done by the default clock registration code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The patches 5d0b7235d8 and
bafaecd11d broke the UML build:
On Sun, 17 Jan 2010, Ingo Molnar wrote:
>
> FYI, -tip testing found that these changes break the UML build:
>
> kernel/built-in.o: In function `__up_read':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:192: undefined reference to `call_rwsem_wake'
> kernel/built-in.o: In function `__up_write':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:210: undefined reference to `call_rwsem_wake'
> kernel/built-in.o: In function `__downgrade_write':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:228: undefined reference to `call_rwsem_downgrade_wake'
> kernel/built-in.o: In function `__down_read':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:112: undefined reference to `call_rwsem_down_read_failed'
> kernel/built-in.o: In function `__down_write_nested':
> /home/mingo/tip/arch/x86/include/asm/rwsem.h:154: undefined reference to `call_rwsem_down_write_failed'
> collect2: ld returned 1 exit status
Add lib/rwsem_64.o to the UML subarch objects to fix.
LKML-Reference: <alpine.LFD.2.00.1001171023440.13231@localhost.localdomain>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LAN9115 Ethernet only works on SMDK6410 if certain switches
are set in specific ways. Document the requirement.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds the physical address of the SROM unit, and
applies a virtual mapping for it to the S3C_VA_MEM
slot.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since the mach-smdk6410.c file claims it can start up the
smsc9115 ethernet device on the board, it should take care
about configuring the necessary chip select nCS1 so it can
see the chip. The select defaults to 8-bit mode so without
config the Ethernet doesn't work.
This patch uses the new SROM definitions to set nCS1 to the
state found in the Samsung U-Boot port for 6410. It may be
more conservative that it needs to be since those settings
were marked as for CS8900A also using this chip select.
But this change is enough to get the ethernet working when
booted with Qi.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This introduces a platform file for s3c64xx that defines
the SROM unit registers that control chip select
characteristics.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define resources needed by the I2S drivers in platform code.
Audio cfg_gpio callback and IORESOURCE_DMA are added.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
do_add_mount() should sanitize mnt_flags
CIFS shouldn't make mountpoints shrinkable
mnt_flags fixes in do_remount()
attach_recursive_mnt() needs to hold vfsmount_lock over set_mnt_shared()
may_umount() needs namespace_sem
Fix configfs leak
Fix the -ESTALE handling in do_filp_open()
ecryptfs: Fix refcnt leak on ecryptfs_follow_link() error path
Fix ACC_MODE() for real
Unrot uml mconsole a bit
hppfs: handle ->put_link()
Kill 9p readlink()
fix autofs/afs/etc. magic mountpoint breakage
The old driver has the number of SSI units in the system hardcoded,
does not make use of the device model and works only on i.MX21/27.
This driver replaces it. It works in DMA mode on i.MX21/27 and using
an FIQ handler on other systems. It also supports AC97 mode of
the SSI units.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Ensure hub revision set for all ACPI modes.
x86, uv: Add function retrieving node controller revision number
x86: xen: 64-bit kernel RPL should be 0
x86: kernel_thread() -- initialize SS to a known state
x86/agp: Fix agp_amd64_init and agp_amd64_cleanup
x86: SGI UV: Fix mapping of MMIO registers
x86: mce.h: Fix warning in header checks
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Check if /dev/null can be used as the -o gcc argument
perf tools: Move QUIET_STDERR def to before first use
perf: Stop stack frame walking off kernel addresses boundaries
The m68knommu coldfire pit clocksource looks like it was incorrectly
marked as a continuous clocksource. Running with it marked as a
continuous clocksource could cause hangs when the system switches to
highres mode or enables nohz.
This patch removes the CLOCK_SOURCE_IS_CONTINUOUS flag on the coldfire pit
clocksource. This will disallow systems using this clocksource from
entering oneshot mode (disabling highres timers and nohz).
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Steven King <sfking@fdwdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
