Use the %pMF kernel extension to display the MAC address.
The address will still be displayed in the FDDI Canonical format.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.
These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.
This problem was introduced in commit 7fd96ce47f ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure on request_irq() is always fatal but unlike other fatal
errors it's only reported to the user if net_debug is set. Make the
diagnostic unconditional and raise the priority so that errors are
more obvious to the user.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed missing newlines in calls to dev_warn & dev_err.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't send flow control settings to any port other than the modem port.
Older firmware ignored this request but did sent a reply. Newer firmware just
ignores it without reply and causes a 5 second timeout every time a port
(except for the modem port) is opened or if tiocm settings are changed.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to reset the usb device when we receive usb bus errors.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't change the state of a port if it's not open. This fixes an issue where a
port sometimes has to be opened twice before data can be received.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields are always little endian and have to be converted on big endian
machines.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_device_id also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: David S. Miller <davem@davemloft.net>
Use #include <linux/ not #include <asm/
Add spaces after arguments
Comment neatening
Make a couple of arrays static const
Align function arguments
Wrap text at 80 columns where reasonable
Cuddle brace else
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use printk_once
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert printks without KERN_<level> to pr_info and pr_cont
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC Ethernet Transceivers (LAN88710, LAN8710, LAN8720, LAN8187,
LAN8700, LAN83C185) provide a mechanism to conserve power when
the device is not connected to an active link partner
(Energy Detect Mode).
So this patch enables the Energy Detect power-down mode
for these Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.
eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board
$ ifconfig eth0 10.193.20.166
$ ifconfig eth1 10.193.20.167
$ ifconfig eth2 10.193.20.168
then
$ ifconfig eth3 10.193.20.169
The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New handlers are added here to handle:
1) Small frames (<256 bytes) in a single small buffer. Allocate a new
skb and copy the frame.
2) Large frame (>256 bytes) in a page chunk. Allocate an skb, tack it on frags,
post to napi_gro_receive().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using 4-byte aligned headers is problematic for some architectures.
Since qlge uses 4-byte aligned rx buffers we split headers for these
architectures into a separate buffer and then recopy to align on 2-byte boundary.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_detach() does not take the tx_lock, so it's possible that
a call to sky2_xmit_frame is still in progress after
netif_device_detach() is complete.
Take netif_tx_lock() to make sure all transmits have stopped while
we're disabling the devices and that no other CPU is still
transmitting a frame after we've disabling the device.
Proposed fix for "sky2 panic under load" reported by Berck E. Nash.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate code deciding which registers can be accessed out of
sky2_get_regs in preparation for adding more conditions into it.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_init_port_info() fails, cleanup the initialized ports only.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This enables HT association and AMPDU in the receive direction for
STA firmware images on hardware that supports it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU receive doesn't need any special handling, so let's enable
this before tackling the transmit side.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the AP's MCS rate mask to SET_RATE when associating, and make
UPDATE_STADB pass in the peer's HT caps and rates when adding a new
hardware station database entry.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mwl8k_bss_info_changed() would refuse to do anything if
the 'changed' argument indicated that the association status hadn't
changed. Fix this up so that it will allow changing things like the
preamble type, the slot time and the CTS-to-self protection method
without having to reassociate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling SET_RATE, SET_AID, or when creating a station database
entry for our AP, pass in the AP's rate set instead of just blindly
enabling all legacy rates, so as to end up doing the right thing when
talking to 11b-only APs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA firmware, move the per-peer hardware station ID to the
driver-private part of struct ieee80211_sta, where it belongs.
(Since issuing a hardware station database maintenance command sleeps,
we can't hold a reference to the ieee80211_sta * across the command,
and since we won't know the station ID until after the command
completes, we need to re-lookup the sta when the command is done to
write the returned station ID back to its driver-private part.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inserting and removing a hardware station database entry for the AP
when we are in managed mode is currently done in ->bss_info_changed().
To prepare for adding AP mode support, implement the ->sta_notify()
driver method, and let that handle inserting and removing the hardware
station database entry for our AP instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
