This reverts commit 747dba7de2.
It breaks concurrent vbi and video capturing:
While v4l2->users is the number of users of the whole device (all device nodes),
v4l2_fh_is_singular() only checks the number of users of a specific device node.
As a result. if one device node is open and a second device node is opened
(closed), the device is reinitialized (streaming is stopped).
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 79ef3a8aa1 made
it possible for reads to happen concurrently with resync.
This means that we need to be more careful where read_balancing
is allowed during resync - we can no longer be sure that any
resync that has already started will definitely finish.
So keep read_balancing to before recovery_cp, which is conservative
but safe.
This bug makes it possible to read from a device that doesn't
have up-to-date data, so it can cause data corruption.
So it is suitable for any kernel since 3.11.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
r1_bio->start_next_window is not initialised in the READ
case, so allow_barrier may incorrectly decrement
conf->current_window_requests
which can cause raise_barrier() to block forever.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When both VBI and video are streaming, and video stream is stopped,
a subsequent trial to restart it will fail, because S_FMT will
return -EBUSY.
That prevents applications like zvbi to work properly.
Please notice that, while this fix it fully for zvbi, the
best is to get rid of streaming_users and res_get logic as a hole.
However, this single-line patch is better to be merged at -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sorry for late. This pull request includes some enhancements
for Exynos drm, new feature supports, cleanups and fixups
like below,
- Consider low power transmission for drm mipi dsi module,
and also add non-continuous clock mode support for Exynos
mipi dsi driver.
- Add Exynos3250 SoC support.
- Enhance and clean up ipp framework and fimc driver.
- Update to use component match support and fix up
de-initialization order.
- Remove a direct mmap interface and relevant stuff specific to
Exynos drm, use drm generic mmap interface instead.
And we will remove the specific interface from userspace
library, libdrm soon.
- Use universal plane which allows to replace fake primary plane
with the real one.
- Some code cleanups and fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (40 commits)
drm/exynos: switch to universal plane API
drm/exynos: use drm generic mmap interface
drm/exynos: remove DRM_EXYNOS_GEM_MAP_OFFSET ioctl
drm/exynos: factor out initial setting of each driver
drm/exynos/hdmi: unregister connector on removal
drm/exynos/dp: unregister connector on removal
drm/exynos/dpi: unregister connector and panel on removal
drm/exynos/dsi: unregister connector on removal
drm/exynos/fb: free exynos framebuffer on error
drm/exynos/fbdev: fix fbdev gem object cleanup
drm/exynos: fix drm driver de-initialization order
drm/exynos/ipp: traverse ipp drivers list safely
drm/exynos: update to use component match support
drm/exynos/ipp: add file checks for ioctls
drm/exynos/ipp: remove file argument from node related functions
drm/exynos/fimc: fix source buffer registers
drm/exynos/fimc: simplify buffer queuing
drm/exynos/fimc: do not enable fimc twice
drm/exynos/fimc: avoid clearing overflow bits
drm/exynos/ipp: remove events during command cleaning
...
There are two modprobe parameters for VBI that aren't used
anywhere (one for debug, the other one related to the buffer
size). Get rid of them!
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The poll documentation was incomplete: document how events (POLLPRI)
are handled and fix the documentation of what poll does for display devices
and streaming I/O.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clarify what poll() returns if STREAMON was called but not QBUF.
Make explicit the different behavior for this scenario for
capture and output devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_ctrl_config struct must be zeroed before passing it to
v4l2_ctrl_new_custom(). This was always wrong, but with the recent
v4l2-ctrls.c changes this is now much more likely to lead to a
kernel bug.
This is the only place where this struct wasn't initialized properly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Pridvorov Andrey <ua0lnj@bk.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix build errors in radio-miropcm20.c due to missing header file:
drivers/media/radio/radio-miropcm20.c: In function 'rds_waitread':
drivers/media/radio/radio-miropcm20.c:90:3: error: implicit declaration of function 'inb' [-Werror=implicit-function-declaration]
drivers/media/radio/radio-miropcm20.c: In function 'rds_rawwrite':
drivers/media/radio/radio-miropcm20.c:106:3: error: implicit declaration of function 'outb' [-Werror=implicit-function-declaration]
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Note: the revision text for the v4l2_pix_format change from Laurent
erroneously mentioned 3.16 when it only got merged for 3.17. Fixed
that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bd994ddb2a (vb2: Fix stream start and
buffer completion race) broke the buffer state check in vb2_buffer_done.
So accept all three possible states there since I can no longer tell the
difference between vb2_buffer_done called from start_streaming or from
elsewhere.
Instead add a WARN_ON at the end of start_streaming that will check whether
any buffers were added to the done list, since that implies that the wrong
state was used as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # for v3.15 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The comment for start_streaming that tells the developer with which vb2 state
buffers should be returned to vb2 gave the wrong state. Very confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Recently WARN_ON() calls have been added to warn if the driver is not
properly returning buffers to vb2 in start_streaming (if it fails) or
stop_streaming(). Add comments before those WARN_ON calls that refer
to the videobuf2-core.h header that explains what drivers are supposed
to do in these situations. That should help point developers in the
right direction if they see these warnings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The norm_swidth function was unused and is dropped. It's not clear
what the purpose of that function was.
The norm_maxh function was changed so it tests for 60 Hz standards
rather than for 50 Hz standards. The is the preferred order.
The norm_maxw function was poorly written and used: it gives the maximum
allowed line width for the given standard. For 60 Hz that's 720, but
for 50 Hz that's 768 which allows for 768x576 which gives you square
pixels. For 60 Hz formats it is 640x480 that gives square pixels, so
there is no need to go beyond 720.
The initial width was set using norm_maxh(), which was wrong. Just set
to 720, that's what you normally use. Since the initial standard was
NTSC anyway the initial width was always 720 anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested VBI support and discovered that the wrong offset was used.
After this change it is now working. Verified with CC/XDS for NTSC
and WSS/Teletext on PAL.
It also reported the wrong start lines for the second field. That's
now fixed as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.
In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If one or both of the timings being compared have the standards field
with value 0, then accept that. Only check for matching standards if
both timings have actually filled in that field.
Otherwise no match will ever be found since when timings are detected
the standards field will typically be set to 0 by the driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is useful to test teletext capture applications like alevt and mtt.
It also fixes a previously undetected bug where the PAL VBI start line
of the second field was off by one. Using the new field start defines
helps a lot fixing such bugs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A test in uvc_video_decode_isoc() checks whether an image has been
received from the camera completely. For this the data amount is compared
to the buffer length, which, however, doesn't have to be equal to the
image size. Switch to using formats .sizeimage field for an exact
expected image size.
[Renamed image_size to frame_size]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/hackrf/hackrf.c:64:3: warning: this decimal constant is unsigned only in ISO C90 [enabled by default]
.rangehigh = 4294967294, /* max u32, hw goes over 7GHz */
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 driver for HackRF SDR. Very basic version, with reduced
feature set. Driver implements receiver only, hardware supports
also transmitter.
USB ID 1d50:6089. Model HackRF One
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The existing RGB555X pixel format is ill-defined in respect to its alpha
bit and its meaning is driver dependent. Create new standard ARGB555X
and XRGB555X variants with clearly defined meanings and make the
existing variant deprecated.
The new pixel formats 4CC values have been selected to match the DRM
4CCs for the same in-memory formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvcvideo webcam driver exposes the v4l2 control "Exposure (Absolute)"
which allows the user to control the exposure time of the webcam,
essentially controlling the brightness of the received image. By default
the webcam automatically adjusts the exposure time automatically but the
if you set the control "Exposure, Auto"="Manual Mode" the user can fix
the exposure time.
Unfortunately it seems that the Logitech C920 has a firmware bug where
it will forget that it's in manual mode temporarily during initialisation.
This means that the camera doesn't respect the exposure time that the user
requested if they request it before starting to stream video. They end up
with a video stream which is either too bright or too dark and must reset
the controls after video starts streaming.
This patch introduces the quirk UVC_QUIRK_RESTORE_CTRLS_ON_INIT which
causes the cached controls to be re-uploaded to the camera immediately
after initialising the camera. This quirk is applied to the C920 to work
around this camera bug.
Signed-off-by: William Manley <will@williammanley.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Map V4L2_CID_TILT_SPEED and V4L2_CID_PAN_SPEED to the standard UVC
CT_PANTILT_RELATIVE_CONTROL terminal control request.
Tested by plugging a Logitech ConferenceCam C3000e USB camera
and controlling pan/tilt from the userspace using the VIDIOC_S_CTRL ioctl.
Verified that it can pan and tilt at the same time in both directions.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch removes unneeded dependency of ARCH_OMAP3
on VIDEO_DM6446_CCDC.
Also the top level platform Makefile descended into
davinci/ without any dependency so just drop the
dependency obj-y, as obj-$(CONFIG_ARCH_DAVINCI)
already exists.
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is possible to call STREAMON without having any buffers queued.
So vb2_is_streaming() can return true without start_streaming()
having been called. Only after at least one buffer has been
queued will start_streaming be called.
The check vb2_is_streaming() is incorrect as this would start
the DMA without having proper DMA pointers set up. this patch
uses vb2_start_streaming_called() instead to check is streaming
was called.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is possible to call STREAMON without having any buffers queued.
So vb2_is_streaming() can return true without start_streaming()
having been called. Only after at least one buffer has been
queued will start_streaming be called.
The check vb2_is_streaming() is incorrect as this would start
the DMA without having proper DMA pointers set up. this patch
uses vb2_start_streaming_called() instead to check is streaming
was called.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops setting of vb2 buffer state to VB2_BUF_STATE_ACTIVE,
as any buffer queued to the driver is marked ACTIVE by the vb2 core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops setting of vb2 buffer state to VB2_BUF_STATE_ACTIVE,
as any buffer queued to the driver is marked ACTIVE by the vb2 core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All the infrastructure for this is already there, and despite our desires for
the old videobuf code to go away, it is currently still in use in 18 drivers.
Allowing reqbufs(0) makes these drivers behave consistent with modern drivers,
making live easier for userspace, see e.g. :
https://bugzilla.gnome.org/show_bug.cgi?id=735660
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
(Changes since v2: dropped local variable as suggested by Laurent)
Commit f035eb4e97 (videobuf2: fix lockdep warning)
unfortunately removed the mmap_sem lock that is needed around the call to
__qbuf_userptr. Amazingly nobody noticed this (especially me as the author)
until Jan Kara pointed this out to me.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Jan Kara <jack@suse.cz>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
