The register map patches didn't set one value for the GMA600 which
means the Fujitsu Q550 dies on boot with the GMA500 driver enabled.
Add the map entry so we don't read from the device MMIO + 0 by mistake.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
"Nothing really major at all:
- fixup edp setup sequence (Dave)
- disable sdvo hotplug for real, this is a fixup for a messed-up
regression fixer (Jani)
- don't expose dysfunctional backlight driver (Jani)
- properly init spinlock (only used by hsw/vlv code) from Alexander
Shishkin"
along with a couple of more fixes on top.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix up the IBX transcoder B check
drm/i915: set the right gen3 flip_done mode also at resume
drm/i915: initialize dpio_lock spin lock
drm/i915: do not expose a dysfunctional backlight interface to userspace
drm/i915: only enable sdvo hotplug irq if needed
drm/i915/edp: get the panel delay before powering up
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet is a bit confusing about this. It says that a dataword has 4
leading zeros, but the first zero is already put on the bus when CS is pulled
low and the second zero is put on the bus on the first leading edge of SCLK, so
when the first bit is sampled on the first trailing edge it will sample what the
datasheet refers to as the second leading zero. Subsequently we only see 3
leading zeros in the 16 bit dataword and the result we get is shifted to the
left by one bit. Fix this by adjusting the channel shift by 1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RX FIFO has a size of 3 characters. Check if when we are picking the
oldest one, we have more to read.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of dev_set_drvdata() and dev_get_drvdata() to store and obtain
a pointer to the ipoctal struct corresponding to a struct dev.
Previously we relied on a private list of devices.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename __tpci_request_irq() to tpci_enable_irq() and __tpci_free_irq()
to tpci_disable_irq(). Change their second argument, move them above
tpci200_interrupt(), and use tpci_disable_irq() in the latter
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the return value from tpci200_interrupt was not quite correct
if a slot had caused an interrupt but no handler was instellalled:
IRQ_NONE was returned. However in this case we react to the interrupt
by disabling the IPack device interrupt.
Basically there are two cases the code now distinguishes:
- The tpci200 has raised an interrupt. We handle it and return
IRQ_HANDLED.
- Our device did not raise an interrupt. We return IRQ_NONE.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the device registers are accessed from both interrupt and
non-interrupt context. To ensure proper read-modify-write modification
of these registers we can not use the "global" tpci200 mutex. Instead
a spin-lock is used.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tpci200_request_irq as well as tpci200_free_irq we set and unset the
pointer to struct slot_irq. This pointer is accessed in
tpci200_interrupt. To ensure that the pointer is not freed after it has
been fetched in tpci200_interrupt() it is now protected through RCU.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each tty's driver_data is now pointing to the channel it is talking to. struct
ipoctal_channel contains all the information the callbacks require to do their
work.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By moving everything channel related into a separate struct we will be
able to clean up a lot of code. In the end tty->driver_data will no
longer need to point to ipoctal but instead can point to the respective
channel.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the __tpci200_{set,clear}_mask routines to access control
register. Do not overwrite flags unrelated to interrupt handling.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a sanity check for the video RAM size. It should fit into the
PCI window.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to select video mode that exceeds the available video
memory. This is potentially dangerous, fix by adding a check.
The patch fixes system hangs seen occasionally when playing random videos
with mplayer.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This macro relies on a local variable having a specific name.
Also, remove the kfree in the detach. The comedi core handles
the kfree of dev->private.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a single source trigger passes "step 1" of the do_cmdtest function
they are already unique. There is no need to recheck them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
