This patch introduces in-kernel handling of some intercepts for privileged
instructions:
handle_set_prefix() sets the prefix register of the local cpu
handle_store_prefix() stores the content of the prefix register to memory
handle_store_cpu_address() stores the cpu number of the current cpu to memory
handle_skey() just decrements the instruction address and retries
handle_stsch() delivers condition code 3 "operation not supported"
handle_chsc() same here
handle_stfl() stores the facility list which contains the
capabilities of the cpu
handle_stidp() stores cpu type/model/revision and such
handle_stsi() stores information about the system topology
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the s390 interrupt subsystem (similar to in kernel apic)
including timer interrupts (similar to in-kernel-pit) and enabled wait
(similar to in kernel hlt).
In order to achieve that, this patch also introduces intercept handling
for instruction intercepts, and it implements load control instructions.
This patch introduces an ioctl KVM_S390_INTERRUPT which is valid for both
the vm file descriptors and the vcpu file descriptors. In case this ioctl is
issued against a vm file descriptor, the interrupt is considered floating.
Floating interrupts may be delivered to any virtual cpu in the configuration.
The following interrupts are supported:
SIGP STOP - interprocessor signal that stops a remote cpu
SIGP SET PREFIX - interprocessor signal that sets the prefix register of a
(stopped) remote cpu
INT EMERGENCY - interprocessor interrupt, usually used to signal need_reshed
and for smp_call_function() in the guest.
PROGRAM INT - exception during program execution such as page fault, illegal
instruction and friends
RESTART - interprocessor signal that starts a stopped cpu
INT VIRTIO - floating interrupt for virtio signalisation
INT SERVICE - floating interrupt for signalisations from the system
service processor
struct kvm_s390_interrupt, which is submitted as ioctl parameter when injecting
an interrupt, also carrys parameter data for interrupts along with the interrupt
type. Interrupts on s390 usually have a state that represents the current
operation, or identifies which device has caused the interruption on s390.
kvm_s390_handle_wait() does handle waitpsw in two flavors: in case of a
disabled wait (that is, disabled for interrupts), we exit to userspace. In case
of an enabled wait we set up a timer that equals the cpu clock comparator value
and sleep on a wait queue.
[christian: change virtio interrupt to 0x2603]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This path introduces handling of sie intercepts in three flavors: Intercepts
are either handled completely in-kernel by kvm_handle_sie_intercept(),
or passed to userspace with corresponding data in struct kvm_run in case
kvm_handle_sie_intercept() returns -ENOTSUPP.
In case of partial execution in kernel with the need of userspace support,
kvm_handle_sie_intercept() may choose to set up struct kvm_run and return
-EREMOTE.
The trivial intercept reasons are handled in this patch:
handle_noop() just does nothing for intercepts that don't require our support
at all
handle_stop() is called when a cpu enters stopped state, and it drops out to
userland after updating our vcpu state
handle_validity() faults in the cpu lowcore if needed, or passes the request
to userland
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the port of Qumranet's kvm kernel module to IBM zSeries
(aka s390x, mainframe) architecture. It uses the mainframe's virtualization
instruction SIE to run virtual machines with up to 64 virtual CPUs each.
This port is only usable on 64bit host kernels, and can only run 64bit guest
kernels. However, running 31bit applications in guest userspace is possible.
The following source files are introduced by this patch
arch/s390/kvm/kvm-s390.c similar to arch/x86/kvm/x86.c, this implements all
arch callbacks for kvm. __vcpu_run calls back into
sie64a to enter the guest machine context
arch/s390/kvm/sie64a.S assembler function sie64a, which enters guest
context via SIE, and switches world before and after that
include/asm-s390/kvm_host.h contains all vital data structures needed to run
virtual machines on the mainframe
include/asm-s390/kvm.h defines kvm_regs and friends for user access to
guest register content
arch/s390/kvm/gaccess.h functions similar to uaccess to access guest memory
arch/s390/kvm/kvm-s390.h header file for kvm-s390 internals, extended by
later patches
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The address 0x11b8 is used by z/VM for pfault and diag 250 I/O to
provide a 64 bit extint parameter. virtio uses the same address, so
its time to update the lowcore structure.
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the s390 memory management defintions to use the pgste field
for dirty and reference bit tracking of host and guest code. Usually on s390,
dirty and referenced are tracked in storage keys, which belong to the physical
page. This changes with virtualization: The guest and host dirty/reference bits
are defined to be the logical OR of the values for the mapping and the physical
page. This patch implements the necessary changes in pgtable.h for s390.
There is a common code change in mm/rmap.c, the call to
page_test_and_clear_young must be moved. This is a no-op for all
architecture but s390. page_referenced checks the referenced bits for
the physiscal page and for all mappings:
o The physical page is checked with page_test_and_clear_young.
o The mappings are checked with ptep_test_and_clear_young and friends.
Without pgstes (the current implementation on Linux s390) the physical page
check is implemented but the mapping callbacks are no-ops because dirty
and referenced are not tracked in the s390 page tables. The pgstes introduces
guest and host dirty and reference bits for s390 in the host mapping. These
mapping must be checked before page_test_and_clear_young resets the reference
bit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The SIE instruction on s390 uses the 2nd half of the page table page to
virtualize the storage keys of a guest. This patch offers the s390_enable_sie
function, which reorganizes the page tables of a single-threaded process to
reserve space in the page table:
s390_enable_sie makes sure that the process is single threaded and then uses
dup_mm to create a new mm with reorganized page tables. The old mm is freed
and the process has now a page status extended field after every page table.
Code that wants to exploit pgstes should SELECT CONFIG_PGSTE.
This patch has a small common code hit, namely making dup_mm non-static.
Edit (Carsten): I've modified Martin's patch, following Jeremy Fitzhardinge's
review feedback. Now we do have the prototype for dup_mm in
include/linux/sched.h. Following Martin's suggestion, s390_enable_sie() does now
call task_lock() to prevent race against ptrace modification of mm_users.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This emulates the x86 hardware task switch mechanism in software, as it is
unsupported by either vmx or svm. It allows operating systems which use it,
like freedos, to run as kvm guests.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
include/linux/kvm.h defines struct kvm_dirty_log to
[...]
union {
void __user *dirty_bitmap; /* one bit per page */
__u64 padding;
};
__user requires compiler.h to compile. Currently, this works on x86
only coincidentally due to other include files. This patch makes
kvm.h compile in all cases.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
it will allow external users to call it. It is mainly
useful for routines that will override its machine_ops
field for its own special purposes, but want to call the
normal shutdown routine after they're done
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch a llows machine_crash_shutdown to
be replaced, just like any of the other functions
in machine_ops
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Hypercall based pte updates are faster than faults, and also allow use
of the lazy MMU mode to batch operations.
Don't report the feature if two dimensional paging is enabled.
[avi:
- one mmu_op hypercall instead of one per op
- allow 64-bit gpa on hypercall
- don't pass host errors (-ENOMEM) to guest]
[akpm: warning fix on i386]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The patch moves the PIT model from userspace to kernel, and increases
the timer accuracy greatly.
[marcelo: make last_injected_time per-guest]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tested-and-Acked-by: Alex Davis <alex14641@yahoo.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
In the current inject_page_fault path KVM only checks if there is another PF
pending and injects a DF then. But it has to check for a pending DF too to
detect a shutdown condition in the VCPU. If this is not detected the VCPU goes
to a PF -> DF -> PF loop when it should triple fault. This patch detects this
condition and handles it with an KVM_SHUTDOWN exit to userspace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Create large pages mappings if the guest PTE's are marked as such and
the underlying memory is hugetlbfs backed. If the largepage contains
write-protected pages, a large pte is not used.
Gives a consistent 2% improvement for data copies on ram mounted
filesystem, without NPT/EPT.
Anthony measures a 4% improvement on 4-way kernbench, with NPT.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Mark zapped root pagetables as invalid and ignore such pages during lookup.
This is a problem with the cr3-target feature, where a zapped root table fools
the faulting code into creating a read-only mapping. The result is a lockup
if the instruction can't be emulated.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This is the host part of kvm clocksource implementation. As it does
not include clockevents, it is a fairly simple implementation. We
only have to register a per-vcpu area, and start writing to it periodically.
The area is binary compatible with xen, as we use the same shadow_info
structure.
[marcelo: fix bad_page on MSR_KVM_SYSTEM_TIME]
[avi: save full value of the msr, even if enable bit is clear]
[avi: clear previous value of time_page]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The load_pdptrs() function is required in the SVM module for NPT support.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The generic x86 code has to know if the specific implementation uses Nested
Paging. In the generic code Nested Paging is called Two Dimensional Paging
(TDP) to avoid confusion with (future) TDP implementations of other vendors.
This patch exports the availability of TDP to the generic x86 code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch give the SVM and VMX implementations the ability to add some bits
the guest can set in its EFER register.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows kvm_host.h to be #included even when struct preempt_notifier is
undefined. This is needed to build ppc asm-offsets.h.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To allow TLB entries to be retained across VM entry and VM exit, the VMM
can now identify distinct address spaces through a new virtual-processor ID
(VPID) field of the VMCS.
[avi: drop vpid_sync_all()]
[avi: add "cc" to asm constraints]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This never was enabled, I could never get it working, and if anyone
wants to try and get it's very easy to reference this code in the
history.
It's the only thing referencing the silly ISA device layer in the
sparc64 tree. OF device layer infrastructure is what should be used
for these things.
Signed-off-by: David S. Miller <davem@davemloft.net>
OK, so 25-mm1 gave a lockdep error which made me look into this.
The first thing that I noticed was the horrible mess; the second thing I
saw was hacks like: 71e93d1561
The problem is that arch idle routines are somewhat inconsitent with
their IRQ state handling and instead of fixing _that_, we go paper over
the problem.
So the thing I've tried to do is set a standard for idle routines and
fix them all up to adhere to that. So the rules are:
idle routines are entered with IRQs disabled
idle routines will exit with IRQs enabled
Nearly all already did this in one form or another.
Merge the 32 and 64 bit bits so they no longer have different bugs.
As for the actual lockdep warning; __sti_mwait() did a plainly un-annotated
irq-enable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[mingo@elte.hu: split from "x86_64: get boot_cpu_id as early for k8_scan_nodes]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, on an amd k8 system with multi ht chains, the numa_node of
pci devices under /sys/devices/pci0000:80/* is always 0, even if that
chain is on node 1 or 2 or 3.
Workaround: pcibus_to_node(bus) is used when we want to get the node that
pci_device is on.
In struct device, we already have numa_node member, and we could use
dev_to_node()/set_dev_node() to get and set numa_node in the device.
set_dev_node is called in pci_device_add() with pcibus_to_node(bus),
and pcibus_to_node uses bus->sysdata for nodeid.
The problem is when pci_add_device is called, bus->sysdata is not assigned
correct nodeid yet. The result is that numa_node will always be 0.
pcibios_scan_root and pci_scan_root could take sysdata. So we need to get
mp_bus_to_node mapping before these two are called, and thus
get_mp_bus_to_node could get correct node for sysdata in root bus.
In scanning of the root bus, all child busses will take parent bus sysdata.
So all pci_device->dev.numa_node will be assigned correctly and automatically.
Later we could use dev_to_node(&pci_dev->dev) to get numa_node, and we
could also could make other bus specific device get the correct numa_node
too.
This is an updated version of pci_sysdata and Jeff's pci_domain patch.
[ mingo@elte.hu: build fix ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
doesn't need to check if it is type1 or type2, we can use raw_pci_ops
directly.
also make pci_direct_conf1 static again.
anyway is there system with type 2 and mmconf support?
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources. If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table. The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.
In order to do this, MMCONFIG setup has been split into two phases. If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before. Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources. Presently this is just triggered off
the end of ACPI interpreter initialization.
There are a few other behavioral changes here:
- Validate all MMCONFIG configurations provided, not just the first one.
- Validate the entire required length of each configuration according to
the provided ending bus number is reserved, not just the minimum required
allocation.
- Validate that the area is reserved even if we read it from the chipset
directly and not from the MCFG table. This catches the case where the
BIOS didn't set the location properly in the chipset and has mapped it
over other things it shouldn't have.
This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.
Based on an original patch by Rajesh Shah from Intel.
[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3:
x86_64/mm: check and print vmemmap allocation continuous
x86_64: fix setup_node_bootmem to support big mem excluding with memmap
x86_64: make reserve_bootmem_generic() use new reserve_bootmem()
mm: allow reserve_bootmem() cross nodes
mm: offset align in alloc_bootmem()
mm: fix alloc_bootmem_core to use fast searching for all nodes
mm: make mem_map allocation continuous
On big systems with lots of memory, don't print out too much during
bootup, and make it easy to find if it is continuous.
on 256G 8 sockets system will get
[ffffe20000000000-ffffe20002bfffff] PMD -> [ffff810001400000-ffff810003ffffff] on node 0
[ffffe2001c700000-ffffe2001c7fffff] potential offnode page_structs
[ffffe20002c00000-ffffe2001c7fffff] PMD -> [ffff81000c000000-ffff8100255fffff] on node 0
[ffffe20038700000-ffffe200387fffff] potential offnode page_structs
[ffffe2001c800000-ffffe200387fffff] PMD -> [ffff810820200000-ffff81083c1fffff] on node 1
[ffffe20040000000-ffffe2007fffffff] PUD ->ffff811027a00000 on node 2
[ffffe20038800000-ffffe2003fffffff] PMD -> [ffff811020200000-ffff8110279fffff] on node 2
[ffffe20054700000-ffffe200547fffff] potential offnode page_structs
[ffffe20040000000-ffffe200547fffff] PMD -> [ffff811027c00000-ffff81103c3fffff] on node 2
[ffffe20070700000-ffffe200707fffff] potential offnode page_structs
[ffffe20054800000-ffffe200707fffff] PMD -> [ffff811820200000-ffff81183c1fffff] on node 3
[ffffe20080000000-ffffe200bfffffff] PUD ->ffff81202fa00000 on node 4
[ffffe20070800000-ffffe2007fffffff] PMD -> [ffff812020200000-ffff81202f9fffff] on node 4
[ffffe2008c700000-ffffe2008c7fffff] potential offnode page_structs
[ffffe20080000000-ffffe2008c7fffff] PMD -> [ffff81202fc00000-ffff81203c3fffff] on node 4
[ffffe200a8700000-ffffe200a87fffff] potential offnode page_structs
[ffffe2008c800000-ffffe200a87fffff] PMD -> [ffff812820200000-ffff81283c1fffff] on node 5
[ffffe200c0000000-ffffe200ffffffff] PUD ->ffff813037a00000 on node 6
[ffffe200a8800000-ffffe200bfffffff] PMD -> [ffff813020200000-ffff8130379fffff] on node 6
[ffffe200c4700000-ffffe200c47fffff] potential offnode page_structs
[ffffe200c0000000-ffffe200c47fffff] PMD -> [ffff813037c00000-ffff81303c3fffff] on node 6
[ffffe200c4800000-ffffe200e07fffff] PMD -> [ffff813820200000-ffff81383c1fffff] on node 7
instead of a very long print out...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
typical case: four sockets system, every node has 4g ram, and we are using:
memmap=10g$4g
to mask out memory on node1 and node2
when numa is enabled, early_node_mem is used to get node_data and node_bootmap.
if it can not get memory from the same node with find_e820_area(), it will
use alloc_bootmem to get buff from previous nodes.
so check it and print out some info about it.
need to move early_res_to_bootmem into every setup_node_bootmem.
and it takes range that node has. otherwise alloc_bootmem could return addr
that reserved early.
depends on "mm: make reserve_bootmem can crossed the nodes".
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-generic-bitops-v3:
x86, bitops: select the generic bitmap search functions
x86: include/asm-x86/pgalloc.h/bitops.h: checkpatch cleanups - formatting only
x86: finalize bitops unification
x86, UML: remove x86-specific implementations of find_first_bit
x86: optimize find_first_bit for small bitmaps
x86: switch 64-bit to generic find_first_bit
x86: generic versions of find_first_(zero_)bit, convert i386
bitops: use __fls for fls64 on 64-bit archs
generic: implement __fls on all 64-bit archs
generic: introduce a generic __fls implementation
x86: merge the simple bitops and move them to bitops.h
x86, generic: optimize find_next_(zero_)bit for small constant-size bitmaps
x86, uml: fix uml with generic find_next_bit for x86
x86: change x86 to use generic find_next_bit
uml: Kconfig cleanup
uml: fix build error
* Export ide_dma_exec_cmd() and __ide_dma_test_irq().
* Constify struct ide_dma_ops.
* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
(it is later overriden by ide_init_port() if needed) and drop
'const struct ide_port_info *d' argument.
While at it:
* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
