Until now the regulator nodes for powering USB VBUS
existed only for the two host controllers. Now the regulator
is added for USB OTG too.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the LeMaker Banana Pi, probing the external ethernet PHY connected
to the SoC's internal GMAC module sometimes fails. The PHY power
supply is handled via a GPIO-controlled regulator, and the existing
regulator startup-delay of 50000us is too short to make sure that the
PHY is always fully powered up when it is queried by phylib. Tests
have shown that to provide a reliable PHY detection, the startup-delay
has to be increased to at least 60000us. To have a certain safety margin
and to cater for manufacturing variations between different boards,
the delay gets set to 100000us as discussed on the linux-arm-kernel
mailinglist.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The apb2 clocks are actually the same as apb1 clocks on the other sunxi
platforms, hence compatible with "allwinner,sun4i-a10-apb1-clk".
Update the dtsi to use the new unified apb1 clk.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With the new factors infrastructure in place, we can unify apb1 and
apb1_mux as a single clock now.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Change apb1 node label to "apb1"; reword commit title]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: FUKAUMI Naoki <naobsd@gmail.com>
The A80 Optimus board exposes uart4 on the GPIO expansion header.
Enable it so we can use it.
Also enable the internal pull-ups, as there doesn't seem to be
external pull-up resistors for pins on the expansion header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 is exposed on the GPIO extension header. Enable it so we can use it.
Also enable internal pull-ups on the pins, as they don't seem to have
external pull-up resistors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 pinctrl driver is just as usual our pinctrl/gpio/external interrupt
controller.
Nothing really out of the extraordinary here...
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Roman Byshko <rbyshko@gmail.com>
During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Now that we have driver support for the basic clocks, add them to the
dtsi and update existing peripherals. Also add reset controls to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
This patch adds only basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
The Allwinner A80 is a new multi-purpose SoC with 4 Cortex-A7 and
4 Cortex-A15 cores in a big.LITTLE architecture, and a 64-core
PowerVR G6230 GPU.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
The Mele M3 is yet another Allwinnner based Android top set box from Mele.
It uses a housing similar to the A2000, but without the USM sata storage slot
at the top.
It features an A20 SoC, 1G RAM, 4G eMMC (unique for Allwinner devices),
100Mbit ethernet, HDMI out, 3 USB A receptacles, VGA, and A/V OUT connections.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:
http://www.lemaker.org/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The uart3_pins_a multiplexes the uart3 pins to port G, add a pinctrl entry
for mapping them to port H (as used on the Bananapi).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull more perf updates from Ingo Molnar:
"A second (and last) round of late coming fixes and changes, almost all
of them in perf tooling:
User visible tooling changes:
- Add period data column and make it default in 'perf script' (Jiri
Olsa)
- Add a visual cue for toggle zeroing of samples in 'perf top'
(Taeung Song)
- Improve callchains when using libunwind (Namhyung Kim)
Tooling fixes and infrastructure changes:
- Fix for double free in 'perf stat' when using some specific invalid
command line combo (Yasser Shalabi)
- Fix off-by-one bugs in map->end handling (Stephane Eranian)
- Fix off-by-one bug in maps__find(), also related to map->end
handling (Namhyung Kim)
- Make struct symbol->end be the first addr after the symbol range,
to make it match the convention used for struct map->end. (Arnaldo
Carvalho de Melo)
- Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
live' (Jiri Olsa)
- Fix python test build by moving callchain_param to an object linked
into the python binding (Jiri Olsa)
- Document sysfs events/ interfaces (Cody P Schafer)
- Fix typos in perf/Documentation (Masanari Iida)
- Add missing 'struct option' forward declaration (Arnaldo Carvalho
de Melo)
- Add option to copy events when queuing for sorting across cpu
buffers and enable it for 'perf kvm stat live', to avoid having
events left in the queue pointing to the ring buffer be rewritten
in high volume sessions. (Alexander Yarygin, improving work done
by David Ahern):
- Do not include a struct hists per perf_evsel, untangling the
histogram code from perf_evsel, to pave the way for exporting a
minimalistic tools/lib/api/perf/ library usable by tools/perf and
initially by the rasd daemon being developed by Borislav Petkov,
Robert Richter and Jean Pihet. (Arnaldo Carvalho de Melo)
- Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
thread maps mean syswide monitoring, reducing the boilerplate for
tools that only want system wide mode. (Arnaldo Carvalho de Melo)
- Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
should be just a front end for exit + free (Arnaldo Carvalho de
Melo)
- Add support to new style format of kernel PMU event. (Kan Liang)
and other misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
perf script: Add period as a default output column
perf script: Add period data column
perf evsel: No need to drag util/cgroup.h
perf evlist: Add missing 'struct option' forward declaration
perf evsel: Move exit stuff from __delete to __exit
kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
perf kvm stat live: Enable events copying
perf session: Add option to copy events when queueing
perf Documentation: Fix typos in perf/Documentation
perf trace: Use thread_{,_set}_priv helpers
perf kvm: Use thread_{,_set}_priv helpers
perf callchain: Create an address space per thread
perf report: Set callchain_param.record_mode for future use
perf evlist: Fix for double free in tools/perf stat
perf test: Add test case for pmu event new style format
perf tools: Add support to new style format of kernel PMU event
perf tools: Parse the pmu event prefix and suffix
Revert "perf tools: Default to cpu// for events v5"
perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
perf Documentation: sysfs events/ interfaces
...
This breaks the stack end corruption detection facility.
What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.
"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.
So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.
Fix this by making the size explicit.
Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves. So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.
Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:
1) For pre-hypervisor TLB protection violation traps, if we took
the 'winfix_trampoline' path we wouldn't have %g4 initialized
with the FAULT_CODE_* value yet. Resulting in using the
TLB_TAG_ACCESS register address value instead.
2) In the TSB miss path, when we notice that we are going to use a
hugepage mapping, but we haven't allocated the hugepage TSB yet, we
still have to take the window fixup case into consideration and
in that particular path we leave %g4 not setup properly.
Errors on this sort were largely invisible previously, but after
commit 4ccb927289 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.
FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.
Fixes: 4ccb927289 ("sparc64: sun4v TLB error power off events")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
