In get_initial_state, it calls notify_initial_state_done(skb,..) if
cb->args[5]==1. If genlmsg_put() failed in notify_initial_state_done(),
the skb will be freed by nlmsg_free(skb).
Then get_initial_state will goto out and the freed skb will be used by
return value skb->len, which is a uaf bug.
What's worse, the same problem goes even further: skb can also be
freed in the notify_*_state_change -> notify_*_state calls below.
Thus 4 additional uaf bugs happened.
My patch lets the problem callee functions: notify_initial_state_done
and notify_*_state_change return an error code if errors happen.
So that the error codes could be propagated and the uaf bugs can be avoid.
v2 reports a compilation warning. This v3 fixed this warning and built
successfully in my local environment with no additional warnings.
v2: https://lore.kernel.org/patchwork/patch/1435218/
Fixes: a29728463b ("drbd: Backport the "events2" command")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace the blk_poll interface that requires the caller to keep a queue
and cookie from the submissions with polling based on the bio.
Polling for the bio itself leads to a few advantages:
- the cookie construction can made entirely private in blk-mq.c
- the caller does not need to remember the request_queue and cookie
separately and thus sidesteps their lifetime issues
- keeping the device and the cookie inside the bio allows to trivially
support polling BIOs remapping by stacking drivers
- a lot of code to propagate the cookie back up the submission path can
be removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mark Wunderlich <mark.wunderlich@intel.com>
Link: https://lore.kernel.org/r/20211012111226.760968-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block driver updates from Jens Axboe:
- Remove the skd driver. It's been EOL for a long time (Damien)
- NVMe pull requests
- fix multipath handling of ->queue_rq errors (Chao Leng)
- nvmet cleanups (Chaitanya Kulkarni)
- add a quirk for buggy Amazon controller (Filippo Sironi)
- avoid devm allocations in nvme-hwmon that don't interact well
with fabrics (Hannes Reinecke)
- sysfs cleanups (Jiapeng Chong)
- fix nr_zones for multipath (Keith Busch)
- nvme-tcp crash fix for no-data commands (Sagi Grimberg)
- nvmet-tcp fixes (Sagi Grimberg)
- add a missing __rcu annotation (Christoph)
- failed reconnect fixes (Chao Leng)
- various tracing improvements (Michal Krakowiak, Johannes
Thumshirn)
- switch the nvmet-fc assoc_list to use RCU protection (Leonid
Ravich)
- resync the status codes with the latest spec (Max Gurtovoy)
- minor nvme-tcp improvements (Sagi Grimberg)
- various cleanups (Rikard Falkeborn, Minwoo Im, Chaitanya
Kulkarni, Israel Rukshin)
- Floppy O_NDELAY fix (Denis)
- MD pull request
- raid5 chunk_sectors fix (Guoqing)
- Use lore links (Kees)
- Use DEFINE_SHOW_ATTRIBUTE for nbd (Liao)
- loop lock scaling (Pavel)
- mtip32xx PCI fixes (Bjorn)
- bcache fixes (Kai, Dongdong)
- Misc fixes (Tian, Yang, Guoqing, Joe, Andy)
* tag 'for-5.12/drivers-2021-02-17' of git://git.kernel.dk/linux-block: (64 commits)
lightnvm: pblk: Replace guid_copy() with export_guid()/import_guid()
lightnvm: fix unnecessary NULL check warnings
nvme-tcp: fix crash triggered with a dataless request submission
block: Replace lkml.org links with lore
nbd: Convert to DEFINE_SHOW_ATTRIBUTE
nvme: add 48-bit DMA address quirk for Amazon NVMe controllers
nvme-hwmon: rework to avoid devm allocation
nvmet: remove else at the end of the function
nvmet: add nvmet_req_subsys() helper
nvmet: use min of device_path and disk len
nvmet: use invalid cmd opcode helper
nvmet: use invalid cmd opcode helper
nvmet: add helper to report invalid opcode
nvmet: remove extra variable in id-ns handler
nvmet: make nvmet_find_namespace() req based
nvmet: return uniform error for invalid ns
nvmet: set status to 0 in case for invalid nsid
nvmet-fc: add a missing __rcu annotation to nvmet_fc_tgt_assoc.queues
nvme-multipath: set nr_zones for zoned namespaces
nvmet-tcp: fix potential race of tcp socket closing accept_work
...
Given that drbd_md_io_bio_set is initialized during module initialization
and the module fails to load if the initialization fails there is no need
to fall back to plain bio_alloc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace the gendisk pointer in struct bio with a pointer to the newly
improved struct block device. From that the gendisk can be trivially
accessed with an extra indirection, but it also allows to directly
look up all information related to partition remapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
DRBD keeps a block device open just to get and set the capacity from
it. Switch to primarily using the disk capacity as intended by the
block layer, and sync it to the bdev using revalidate_disk_size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
generic_make_request has always been very confusingly misnamed, so rename
it to submit_bio_noacct to make it clear that it is submit_bio minus
accounting and a few checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The make_request_fn is a little weird in that it sits directly in
struct request_queue instead of an operation vector. Replace it with
a block_device_operations method called submit_bio (which describes much
better what it does). Also remove the request_queue argument to it, as
the queue can be derived pretty trivially from the bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code should
always use “flexible array members”[1] for these cases. The older style of
one-element or zero-length arrays should no longer be used[2].
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://github.com/KSPP/linux/issues/21
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Add a helper to directly set the TCP_QUICKACK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_NODELAY sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to directly set the TCP_CORK sockopt from kernel space
without going through a fake uaccess. Cleanup the callers to avoid
pointless wrappers now that this is a simple function call.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching to struct_size for the allocation in fifo_alloc avoids
hard-coding the type of fifo_buffer.values in fifo_alloc. It also
provides overflow protection; to avoid pessimistic code being
generated by the compiler as a result, this patch also switches
fifo_size to unsigned, propagating the change as appropriate.
Reviewed-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
The drbd module exclusively sends signals to kernel threads it creates with
kthread_create. These kernel threads do not block or ignore signals (only
flush signals after they have been delivered), nor can drbd threads
possibly be pid namespace init processes so the extra work that force_sig
performs that send_sig does not is unnecessary.
Further force_sig is for delivering synchronous signals (aka exceptions).
The locking in force_sig is not prepared to deal with running processes, as
tsk->sighand may change during exec for a running process.
In short it is not only unnecessary for drbd to use force_sig it is
semantically wrong.
With drbd using send_sig it becomes easier to maintain force_sig as only
synchronous signals need to be considered.
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: drbd-dev@lists.linbit.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Based on 1 normalized pattern(s):
is free software you can redistribute it and or modify it under the
terms of the gnu general public license as published by the free
software foundation either version 2 or at your option any later
version [drbd] is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with [drbd] see the
file copying if not write to the free software foundation 675 mass
ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 16 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520075212.050796421@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/block/drbd/drbd_int.h:1774:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_int.h:1774:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_int.h:1774:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_int.h:1774:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_int.h:1774:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_receiver.c:3093:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_receiver.c:3120:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/block/drbd/drbd_req.c:856:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
And also re-enable partial-zero-out + discard aligned.
With the introduction of REQ_OP_WRITE_ZEROES,
we started to use that for both WRITE_ZEROES and DISCARDS,
hoping that WRITE_ZEROES would "do what we want",
UNMAP if possible, zero-out the rest.
The example scenario is some LVM "thin" backend.
While an un-allocated block on dm-thin reads as zeroes, on a dm-thin
with "skip_block_zeroing=true", after a partial block write allocated
that block, that same block may well map "undefined old garbage" from
the backends on LBAs that have not yet been written to.
If we cannot distinguish between zero-out and discard on the receiving
side, to avoid "undefined old garbage" to pop up randomly at later times
on supposedly zero-initialized blocks, we'd need to map all discards to
zero-out on the receiving side. But that would potentially do a full
alloc on thinly provisioned backends, even when the expectation was to
unmap/trim/discard/de-allocate.
We need to distinguish on the protocol level, whether we need to guarantee
zeroes (and thus use zero-out, potentially doing the mentioned full-alloc),
or if we want to put the emphasis on discard, and only do a "best effort
zeroing" (by "discarding" blocks aligned to discard-granularity, and zeroing
only potential unaligned head and tail clippings to at least *try* to
avoid "false positives" in an online-verify later), hoping that someone
set skip_block_zeroing=false.
For some discussion regarding this on dm-devel, see also
https://www.mail-archive.com/dm-devel%40redhat.com/msg07965.htmlhttps://www.redhat.com/archives/dm-devel/2018-January/msg00271.html
For backward compatibility, P_TRIM means zero-out, unless the
DRBD_FF_WZEROES feature flag is agreed upon during handshake.
To have upper layers even try to submit WRITE ZEROES requests,
we need to announce "efficient zeroout" independently.
We need to fixup max_write_zeroes_sectors after blk_queue_stack_limits():
if we can handle "zeroes" efficiently on the protocol,
we want to do that, even if our backend does not announce
max_write_zeroes_sectors itself.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, some implicit resizes that happend during handshake
have not been reported as prominently as explicit resize.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparing to remove all stack VLA usage from the kernel[1], this
removes the discouraged use of AHASH_REQUEST_ON_STACK in favor of
the smaller SHASH_DESC_ON_STACK by converting from ahash-wrapped-shash
to direct shash. By removing a layer of indirection this both improves
performance and reduces stack usage. The stack allocation will be made
a fixed size in a later patch to the crypto subsystem.
The bulk of the lines in this change are simple s/ahash/shash/, but the
main logic differences are in drbd_csum_ee() and drbd_csum_bio(), which
externalizes the page walking with k(un)map_atomic() instead of using
scattergather.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a follow-up to Gregs complaints that drbd clutteres the global
namespace.
Some of DRBD's module parameters are only used within one compilation
unit. Make these static.
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Nothing like having a very generic global variable in a tiny driver
subsystem to make a mess of the global namespace...
Note, there are many other "generic" named global variables in the drbd
subsystem, someone should fix those up one day before they hit a linking
error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Recently, drbd_recv_header() was changed to potentially
implicitly "unplug" the backend device(s), in case there
is currently nothing to receive.
Be more explicit about it: re-introduce the original drbd_recv_header(),
and introduce a new drbd_recv_header_maybe_unplug() for use by the
receiver "main loop".
Using explicit plugging via blk_start_plug(); blk_finish_plug();
really helps the io-scheduler of the backend with merging requests.
Wrap the receiver "main loop" with such a plug.
Also catch unplug events on the Primary,
and try to propagate.
This is performance relevant. Without this, if the receiving side does
not merge requests, number of IOPS on the peer can me significantly
higher than IOPS on the Primary, and can easily become the bottleneck.
Together, both changes should help to reduce the number of IOPS
as seen on the backend of the receiving side, by increasing
the chance of merging mergable requests, without trading latency
for more throughput.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drbd does not modify the bi_io_vec of the cloned bio,
so there is no need to clone that part. So bio_clone_fast()
is the better choice.
For bio_clone_fast() we need to specify a bio_set.
We could use fs_bio_set, which bio_clone() uses, or
drbd_md_io_bio_set, which drbd uses for metadata, but it is
generally best to avoid sharing bio_sets unless you can
be certain that there are no interdependencies.
So create a new bio_set, drbd_io_bio_set, and use bio_clone_fast().
Also remove a "XXX cannot fail ???" comment because it definitely
cannot fail - bio_clone_fast() doesn't fail if the GFP flags allow for
sleeping.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
drbd always wants its discard wire operations to zero the blocks, so
use blkdev_issue_zeroout with the BLKDEV_ZERO_UNMAP flag instead of
reinventing it poorly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
For larger devices, the array of bitmap page pointers can grow very
large (8000 pointers per TB of storage).
For each activity log transaction, we need to flush the associated
bitmap pages to stable storage. Currently, we just "mark" the respective
pages while setting up the transaction, then tell the bitmap code to
write out all marked pages, but skip unchanged pages.
But one such transaction can affect only a small number of bitmap pages,
there is no need to scan the full array of several (ten-)thousand
page pointers to find the few marked ones.
Instead, remember the index numbers of the few affected pages,
and later only re-check those to skip duplicates and unchanged ones.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This contains various cosmetic fixes ranging from simple typos to
const-ifying, and using booleans properly.
Original commit messages from Fabian's patch set:
drbd: debugfs: constify drbd_version_fops
drbd: use seq_put instead of seq_print where possible
drbd: include linux/uaccess.h instead of asm/uaccess.h
drbd: use const char * const for drbd strings
drbd: kerneldoc warning fix in w_e_end_data_req()
drbd: use unsigned for one bit fields
drbd: use bool for peer is_ states
drbd: fix typo
drbd: use | for bitmask combination
drbd: use true/false for bool
drbd: fix drbd_bm_init() comments
drbd: introduce peer state union
drbd: fix maybe_pull_ahead() locking comments
drbd: use bool for growing
drbd: remove redundant declarations
drbd: replace if/BUG by BUG_ON
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We will support WRITE_SAME, if
* all peers support WRITE_SAME (both in kernel and DRBD version),
* all peer devices support WRITE_SAME
* logical_block_size is identical on all peers.
We may at some point introduce a fallback on the receiving side
for devices/kernels that do not support WRITE_SAME,
by open-coding a submit loop. But not yet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When resync is finished, we already call the "after-resync-target"
handler (on the former sync target, obviously), once per volume.
Paired with the before-resync-target handler, you can create snapshots,
before the resync causes the volumes to become inconsistent,
and discard those snapshots again, once they are no longer needed.
It was also overloaded to be paired with the "fence-peer" handler,
to "unfence" once the volumes are up-to-date and known good.
This has some disadvantages, though: we call "fence-peer" for the whole
connection (once for the group of volumes), but would call unfence as
side-effect of after-resync-target once for each volume.
Also, we fence on a (current, or about to become) Primary,
which will later become the sync-source.
Calling unfence only as a side effect of the after-resync-target
handler opens a race window, between a new fence on the Primary
(SyncTarget) and the unfence on the SyncTarget, which is difficult to
close without some kind of "cluster wide lock" in those handlers.
We would not need those handlers if we could still communicate.
Which makes trying to aquire a cluster wide lock from those handlers
seem like a very bad idea.
This introduces the "unfence-peer" handler, which will be called
per connection (once for the group of volumes), just like the fence
handler, only once all volumes are back in sync, and on the SyncSource.
Which is expected to be the node that previously called "fence", the
node that is currently allowed to be Primary, and thus the only node
that could trigger a new "fence" that could race with this unfence.
Which makes us not need any cluster wide synchronization here,
serializing two scripts running on the same node is trivial.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the replication link breaks exactly during "resync finished" detection,
finishing too early on the sync source could again lead to UUIDs rotated
too fast, and potentially a spurious full resync on next handshake.
Always wait for explicit resync finished state change notification from
the sync target.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
