Pull mtd updates from Miquel Raynal:
"Core MTD changes:
- dt-bindings: Drop unneeded quotes
- mtdblock: Tolerate corrected bit-flips
- Use of_property_read_bool() for boolean properties
- Avoid magic values
- Avoid printing error messages on probe deferrals
- Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
- Fix error path for nvmem provider
- Fix nvmem error reporting
- Provide unique name for nvmem device
MTD device changes:
- lpddr_cmds: Remove unused words variable
- bcm63xxpart: Remove MODULE_LICENSE in non-modules
SPI NOR core changes:
- Introduce Read While Write support for flashes featuring several
banks
- Set the 4-Byte Address Mode method based on SFDP data
- Allow post_sfdp hook to return errors
- Parse SCCR MC table and introduce support for multi-chip devices
SPI NOR manufacturer drivers changes:
- macronix: Add support for mx25uw51245g with RWW
- spansion:
- Determine current address mode at runtime as it can be changed
in a non-volatile way and differ from factory defaults or from
what SFDP advertises.
- Enable JFFS2 write buffer mode for few ECC'd NOR flashes:
S25FS256T, s25hx and s28hx
- Add support for s25hl02gt and s25hs02gt
Raw NAND core changes:
- Convert to platform remove callback returning void
- Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
- imx: Remove unused is_imx51_nfc and imx53_nfc functions
- omap2: Drop obsolete dependency on COMPILE_TEST
- orion: Use devm_platform_ioremap_resource()
- qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
- stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
- tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
- hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
- Add support for ESMT F50x1G41LB"
* tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (55 commits)
mtd: nand: Convert to platform remove callback returning void
mtd: onenand: omap2: Drop obsolete dependency on COMPILE_TEST
mtd: spi-nor: spansion: Add support for s25hl02gt and s25hs02gt
mtd: spi-nor: spansion: Add a new ->ready() hook for multi-chip device
mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support
mtd: spi-nor: spansion: Rework cypress_nor_get_page_size() for multi-chip device support
mtd: spi-nor: sfdp: Add support for SCCR map for multi-chip device
mtd: spi-nor: Extract volatile register offset from SCCR map
mtd: spi-nor: Allow post_sfdp hook to return errors
mtd: spi-nor: spansion: Rename method to cypress_nor_get_page_size
mtd: spi-nor: spansion: Enable JFFS2 write buffer for S25FS256T
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s25hx SEMPER flash
mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash
mtd: spi-nor: spansion: Determine current address mode
mtd: spi-nor: core: Introduce spi_nor_set_4byte_addr_mode()
mtd: spi-nor: core: Update flash's current address mode when changing address mode
mtd: spi-nor: Stop exporting spi_nor_restore()
mtd: spi-nor: Set the 4-Byte Address Mode method based on SFDP data
mtd: spi-nor: core: Make spi_nor_set_4byte_addr_mode_brwr public
mtd: spi-nor: core: Update name and description of spi_nor_set_4byte_addr_mode
...
Raw NAND core changes:
* Convert to platform remove callback returning void
* Fix spelling mistake waifunc() -> waitfunc()
Raw NAND controller driver changes:
* imx: Remove unused is_imx51_nfc and imx53_nfc functions
* omap2: Drop obsolete dependency on COMPILE_TEST
* orion: Use devm_platform_ioremap_resource()
* qcom:
- Use of_property_present() for testing DT property presence
- Use devm_platform_get_and_ioremap_resource()
* stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
* tmio: Remove reference to config MTD_NAND_TMIO in the parsers
Raw NAND manufacturer driver changes:
* hynix: Fix up bit 0 of sdr_timing_mode
SPI-NAND changes:
* Add support for ESMT F50x1G41LB
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230407190453.66efdf9d@endymion.delvare
clang with W=1 reports
drivers/mtd/nand/raw/mxc_nand.c:1602:19: error: unused function
'is_imx51_nfc' [-Werror,-Wunused-function]
static inline int is_imx51_nfc(struct mxc_nand_host *host)
^
drivers/mtd/nand/raw/mxc_nand.c:1607:19: error: unused function
'is_imx53_nfc' [-Werror,-Wunused-function]
static inline int is_imx53_nfc(struct mxc_nand_host *host)
^
These functions are not used, so remove them.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230321114638.1782086-1-trix@redhat.com
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144715.1543926-1-robh@kernel.org
The continuous read support added recently makes nandsim
unhappy. Indeed, all the supported commands should be re-encoded into
internal commands, so of course there is currently no support for the
commands and patterns needed for continuous reads to work.
I tried to add support for them but nandsim (which is more a tool to
develop/debug upper layers rather than the raw NAND core) suffers from a
big limitation: it's internal parser needs to know what exact operation
is happening when the address cycles are performed. The research is then
sequential from the start up to the address cycles, but does not check
what's coming next even though the information is available. This is a
limitation which is related to the old API used by the core which kind
of forced the controllers to guess what operation was being performed
rather early. Today the core uses a more transparent API called
->exec_op() which no longer requires controller drivers to do any more
guessing, but despite being updated to ->exec_op(), nandsim is still a
bit constrained on this regard and thus cannot handle sequential page
reads because the start sequence beginning is identical to a regular
page read.
If the internal algorithm is updated some day, it should be possible to
make it support sequential page reads by adding something like:
/* Large page devices continuous read page start */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART,
STATE_CMD_READCACHESEQ | ACTION_CPY, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page continue */
{OPT_LARGEPAGE, {STATE_CMD_READCACHESEQ | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page end */
{OPT_LARGEPAGE, {STATE_CMD_READCACHEEND | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
For now, we just return -EOPNOTSUPP when the core asks controller
drivers if they support the feature in order to prevent any further use
of these opcodes.
Note: This is a hack, ->exec_op() is not supposed to check against the
COMMAND opcodes unless _really_ needed.
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Reported-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/linux-mtd/fd34fe55-7f4a-030d-8653-9bb9cf08410d@huawei.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20230310085452.1368716-1-miquel.raynal@bootlin.com
This structure must be zeroed, because it's field 'hw->core' is used as
'parent' in 'clk_core_fill_parent_index()', but it will be uninitialized.
This happens, because when this struct is not zeroed, pointer 'hw' is
"initialized" by garbage, which is valid pointer, but points to some
garbage. So 'hw' will be dereferenced, but 'core' contains some random
data which will be interpreted as a pointer. The following backtrace is
result of dereference of such pointer:
[ 1.081319] __clk_register+0x414/0x820
[ 1.085113] devm_clk_register+0x64/0xd0
[ 1.088995] meson_nfc_probe+0x258/0x6ec
[ 1.092875] platform_probe+0x70/0xf0
[ 1.096498] really_probe+0xc8/0x3e0
[ 1.100034] __driver_probe_device+0x84/0x190
[ 1.104346] driver_probe_device+0x44/0x120
[ 1.108487] __driver_attach+0xb4/0x220
[ 1.112282] bus_for_each_dev+0x78/0xd0
[ 1.116077] driver_attach+0x2c/0x40
[ 1.119613] bus_add_driver+0x184/0x240
[ 1.123408] driver_register+0x80/0x140
[ 1.127203] __platform_driver_register+0x30/0x40
[ 1.131860] meson_nfc_driver_init+0x24/0x30
Fixes: 1e4d3ba668 ("mtd: rawnand: meson: fix the clock")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230227102425.793841-1-AVKrasnov@sberdevices.ru
Pull MTD updates from Miquel Raynal:
"MTD changes:
- parsers: ofpart: add workaround for #size-cells 0
- dt-bindings: partitions: Fix partition node name pattern
- dataflash: remove duplicate SPI ID table
Raw NAND core changes:
- Check the data only read pattern only once
- Prepare the late addition of supported operation checks
- Support for sequential cache reads
- Fix nand_chip kdoc
Raw NAND driver changes:
- Fsl_elbc: Propagate HW ECC settings to HW
- Marvell: Add missing layouts
- Pasemi: Don't use static data to track per-device state
- Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
- tmio_nand: Remove driver
- vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
- Add support for AllianceMemory AS5F34G04SND
- Macronix: use scratch buffer for DMA operation
NAND ECC changes:
- Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
- Misc core fixes
SPI NOR driver changes:
- Spansion: Minor fixes"
* tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (33 commits)
mtd: parsers: ofpart: add workaround for #size-cells 0
mtd: rawnand: sunxi: Precompute the ECC_CTL register value
mtd: rawnand: sunxi: Embed sunxi_nand_hw_ecc by value
mtd: rawnand: sunxi: Update OOB layout to match hardware
mtd: spi-nor: Sort headers alphabetically
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986
dt-bindings: mtd: Split ECC engine with rawnand controller
mtd: rawnand: fsl_elbc: Propagate HW ECC settings to HW
mtd: spinand: Add support for AllianceMemory AS5F34G04SND
dt-bindings: mtd: partitions: Fix partition node name pattern
mtd: spi-nor: Create macros to define chip IDs and geometries
mtd: spi-nor: spansion: Make CFRx reg fields generic
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: core: fix implicit declaration warning
mtd: spinand: macronix: use scratch buffer for DMA operation
mtd: rawnand: Fix nand_chip kdoc
mtd: rawnand: vf610_nfc: use regular comments for functions
mtd: rawnand: Support for sequential cache reads
...
When using the hardware ECC engine, the OOB data is made available in
the NFC_REG_USER_DATA registers, as one 32-bit word per ECC step. Any
additional bytes are only accessible through raw reads and software
descrambling. For efficiency, and to match the vendor driver, ignore
these extra bytes when using hardware ECC.
Note that until commit 34569d8695 ("mtd: rawnand: sunxi: Fix the size
of the last OOB region"), this extra free area was reported with length
zero, so this is not a functional change for any stable kernel user.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-2-samuel@sholland.org
It is possible that current chip->ecc.engine_type value does not match to
configured HW value (if HW ECC checking and generating is enabled or not).
This can happen with old U-Boot bootloader version which either does not
initialize NAND (and let it in some default unusable state) or initialize
NAND with different parameters than what is specified in kernel DTS file.
So if kernel chose to use some chip->ecc.engine_type settings (e.g. from
DTS file) then do not depend on bootloader HW configuration and configures
HW ECC settings according to chip->ecc.engine_type value.
BR_DECC must be set to BR_DECC_CHK_GEN when HW is doing ECC (both
generating and checking), or to BR_DECC_OFF when HW is not doing ECC.
This change fixes usage of SW ECC support in case bootloader explicitly
enabled HW ECC support and kernel DTS file has specified to use SW ECC.
(Of course this works only in case when NAND is not a boot device and both
bootloader and kernel are loaded from different location, e.g. FLASH NOR.)
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230128134111.32559-1-pali@kernel.org
The mx35lf1ge4ab_get_eccsr() function uses an SPI DMA operation to
read the eccsr, hence the buffer should not be on stack. Since commit
380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
the kernel emmits a warning and blocks such operations.
Use the scratch buffer to get eccsr instead of trying to directly read
into a stack-allocated variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y8i85zM0u4XdM46z@makrotopia.org
These comments are not quite in kernel-doc format and they don't need
to be, so just use "/*" comment markers for them. This prevents these
kernel-doc warnings:
drivers/mtd/nand/raw/vf610_nfc.c:210: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Read accessor for internal SRAM buffer
drivers/mtd/nand/raw/vf610_nfc.c:245: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Write accessor for internal SRAM buffer
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230113064004.24391-1-rdunlap@infradead.org
Add support for sequential cache reads for controllers using the generic
core helpers for their fast read/write helpers.
Sequential reads may reduce the overhead when accessing physically
continuous data by loading in cache the next page while the previous
page gets sent out on the NAND bus.
The ONFI specification provides the following additional commands to
handle sequential cached reads:
* 0x31 - READ CACHE SEQUENTIAL:
Requires the NAND chip to load the next page into cache while keeping
the current cache available for host reads.
* 0x3F - READ CACHE END:
Tells the NAND chip this is the end of the sequential cache read, the
current cache shall remain accessible for the host but no more
internal cache loading operation is required.
On the bus, a multi page read operation is currently handled like this:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR+tRR) -- DATA1_IN
00 -- ADDR2 -- 30 -- WAIT_RDY (tR+tRR) -- DATA2_IN
00 -- ADDR3 -- 30 -- WAIT_RDY (tR+tRR) -- DATA3_IN
Sequential cached reads may instead be achieved with:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR) -- \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA1_IN \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA2_IN \
3F -- WAIT_RDY (tRCBSY+tRR) -- DATA3_IN
Below are the read speed test results with regular reads and
sequential cached reads, on NXP i.MX6 VAR-SOM-SOLO in mapping mode with
a NAND chip characterized with the following timings:
* tR: 20 µs
* tRCBSY: 5 µs
* tRR: 20 ns
and the following geometry:
* device size: 2 MiB
* eraseblock size: 128 kiB
* page size: 2 kiB
============= Normal read @ 33MHz =================
mtd_speedtest: eraseblock read speed is 15633 KiB/s
mtd_speedtest: page read speed is 15515 KiB/s
mtd_speedtest: 2 page read speed is 15398 KiB/s
===================================================
========= Sequential cache read @ 33MHz ===========
mtd_speedtest: eraseblock read speed is 18285 KiB/s
mtd_speedtest: page read speed is 15875 KiB/s
mtd_speedtest: 2 page read speed is 16253 KiB/s
===================================================
We observe an overall speed improvement of about 5% when reading
2 pages, up to 15% when reading an entire block. This is due to the
~14us gain on each additional page read (tR - (tRCBSY + tRR)).
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-4-miquel.raynal@bootlin.com
Up to now the pasemi nand driver only supported a single device
instance. However the check for that was racy because two parallel calls
of pasemi_nand_probe() could pass the check
if (pasemi_nand_mtd)
return -ENODEV;
before any of them assigns a non-NULL value to it.
So rework the driver to make use of per-device driver data.
As an intended side effect the driver can bind more than one device and
also gets rid of the check
if (!pasemi_nand_mtd)
return 0;
in the remove callback that could only ever trigger after the above race
happened.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230102124051.1508424-1-u.kleine-koenig@pengutronix.de
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Fix refcount error in del_mtd_device()
- Fix possible resource leak in init_mtd()
- Set ROOT_DEV for partitions marked as rootfs in DT
- Describe marking rootfs partitions in the bindings
- Fix device name leak when register device fails in add_mtd_device()
- Try to find OF node for every MTD partition
- simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
- pxa2xx-flash maps: fix memory leak in probe
- BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
- lpddr2_nvm: Fix possible null-ptr-deref
- inftlcore: fix repeated words in comments
- lart: remove driver
- tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
- mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
- Fixed-partitions: Fix 'sercomm,scpart-id' schema
- Standardize the style in the examples
- Drop object types when referencing other files
- Argue in favor of keeping additionalProperties set to true
- NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
- Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
- Physmap: Reuse the generic definitions
- SPI-NOR: Drop common properties
- Sunxi-nand: Add an example to validate the bindings
- Onenand: Mention the expected node name
- Ingenic: Mark partitions in the controller node as deprecated
- NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
- Remove useless file about partitions
- Clarify all partition subnodes
SPI NOR core changes:
- Add support for flash reset using the dt reset-gpios property.
- Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
- Bypass zero erase size in spi_nor_find_best_erase_type().
- Fix select_uniform_erase to skip 0 erase size
- Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described
solely by the flash's SFDP tables.
- Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
- Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP
discoverable.
SPI NOR manufacturer drivers changes:
- Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
- Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
- Micron - ST: Enable locking for mt25qu256a.
- Winbond: Add support for W25Q512NW-IQ.
- ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
- Drop obsolete dependencies on COMPILE_TEST
- MAINTAINERS: rectify entry for MESON NAND controller bindings
- Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
- marvell: Enable NFC/DEVBUS arbiter
- gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
- mpc5121: Replace NO_IRQ by 0
- lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
- lpc32xx_mlc: Switch to using pm_ptr()
- cadence: Support 64-bit slave dma interface
- rockchip: Describe rk3128-nfc in the bindings
- brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
- winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification"
* tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: rawnand: Drop obsolete dependencies on COMPILE_TEST
mtd: maps: pxa2xx-flash: fix memory leak in probe
mtd: core: Fix refcount error in del_mtd_device()
mtd: spi-nor: add SFDP fixups for Quad Page Program
mtd: spi-nor: issi: is25wp256: Init flash based on SFDP
mtd: spi-nor: winbond: add support for W25Q512NW-IQ
mtd: spi-nor: micron-st: Enable locking for mt25qu256a
mtd: spi-nor: Fix the number of bytes for the dummy cycles
mtd: spi-nor: gigadevice: gd25q256: replace gd25q256_default_init with gd25q256_post_bfpt
mtd: spi-nor: Fix formatting in spi_nor_read_raw() kerneldoc comment
mtd: spi-nor: sysfs: print JEDEC ID for generic flash driver
mtd: spi-nor: add generic flash driver
mtd: spi-nor: fix select_uniform_erase to skip 0 erase size
mtd: spi-nor: move function declaration out of sfdp.h
mtd: spi-nor: remember full JEDEC flash ID
mtd: spi-nor: sysfs: hide manufacturer if it is not set
mtd: spi-nor: hide jedec_id sysfs attribute if not present
mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
mtd: rawnand: marvell: Enable NFC/DEVBUS arbiter
mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
...
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221124115946.5edb771c@endymion.delvare
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_slc.c:318:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
318 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 6b923db286 ("mtd: rawnand: lpc32xx_slc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-2-geert@linux-m68k.org
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_mlc.c:380:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
380 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 782e32a990 ("mtd: rawnand: lpc32xx_mlc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-1-geert@linux-m68k.org
OMAP2 OneNAND driver uses gpmc_omap_onenand_set_timings() provided by
OMAP_GPMC driver, so the latter cannot be module if OneNAND driver is
built-in:
/usr/bin/arm-linux-gnueabi-ld: drivers/mtd/nand/onenand/onenand_omap2.o: in function `omap2_onenand_probe':
onenand_omap2.c:(.text+0x520): undefined reference to `gpmc_omap_onenand_set_timings'
The OMAP_GPMC is also a runtime dependency.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 854fd9209b ("memory: omap-gpmc: Allow building as a module")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221107091520.127053-1-krzysztof.kozlowski@linaro.org
