Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Pull printk fixes from Petr Mladek:
- Prevent a potential deadlock when configuring kgdb console
- Fix a kernel doc warning
* tag 'printk-for-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
kernel/printk/printk.c: Fix W=1 kernel-doc warning
tty: serial: kgdboc: fix mutex locking order for configure_kgdboc()
This moves 32x32 font size limitation checking down to drivers, so that
fbcon can allow large fonts.
We still keep a limitation to 64x128 pixels so as to have a simple bounded
allocation for con_font_get and in the userland kbd tool. That glyph size
will however be enough to have 128x36 characters on a "16/9 8K display".
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151935.112415738@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KD_FONT_OP_SET/GET operations hardcode vpitch to be 32 pixels,
which only dates from the old VGA hardware which as asserting this.
Drivers such as fbcon however do not have such limitation, so this
introduces KD_FONT_OP_SET/GET_TALL operations, which userland can try
to use to avoid this limitation, thus opening the patch to >32 pixels
font height.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151935.013597162@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current con_font_get/set API currently hardcodes a 32-pixel-tall
limitation, which only dates from the old VGA hardware which could not
handle taller fonts than that.
This change just adds a vpitch parameter to release this
constraint. Drivers which do not support vpitch != 32 can just return
EINVAL when it is not 32, font loading tools will revert to trying 32
and succeed.
This change makes the fbcon driver consider vpitch appropriately, thus
making it able to load large fonts.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151934.932642243@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When -Woverride-init is enabled in a build, gcc points out that
qcom_geni_serial_pm_ops contains conflicting initializers:
drivers/tty/serial/qcom_geni_serial.c:1586:20: error: initialized field overwritten [-Werror=override-init]
1586 | .restore = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/qcom_geni_serial.c:1586:20: note: (near initialization for 'qcom_geni_serial_pm_ops.restore')
drivers/tty/serial/qcom_geni_serial.c:1587:17: error: initialized field overwritten [-Werror=override-init]
1587 | .thaw = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Open-code the initializers with the version that was already used,
and use the pm_sleep_ptr() method to deal with unused ones,
in place of the __maybe_unused annotation.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221215165453.1864836-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ba47f97a18 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. In addition, the i.MX UART receiver is no longer turned on and off during
sending, because now the hardware is responsible for connecting or disconnecting
RX during TX controlled by this GPIO.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-3-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing clk_disable_unprepare() before return from
tegra_uart_hw_init() in the error handling path.
When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk'
has been enabled, fix it by adding clk_disable_unprepare().
Fixes: cc9ca4d958 ("serial: tegra: Only print FIFO error message when an error occurs")
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.
Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
