Need to bring commit d8bb92e70a ("drm/dp: Factor out a function to
probe a DPCD address") back as a dependency to further work in
drm-intel-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Sync up with v5.18-rc1, in particular to get 5e3094cfd9
("drm/i915/xehpsdv: Add has_flat_ccs to device info").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
At least some DELL monitors (P2715Q) with DPCD_REV 1.2 return corrupted
DPCD register values when reading from the 0xF0000- LTTPR range with an
AUX transaction block size bigger than 1. The DP standard requires 0 to
be returned - as for any other reserved/invalid addresses - but these
monitors return the DPCD_REV register value repeated in each byte of the
read buffer. This will in turn corrupt the values returned by the LTTPRs
between the source and the monitor: LTTPRs must adjust the values they
read from the downstream DPRX, for instance right-shift/init the
downstream DP_PHY_REPEATER_CNT value. Since the value returned by the
monitor's DPRX is non-zero the adjusted values will be corrupt.
Reading the LTTPR registers one-by-one instead of reading all of them
with a single AUX transfer works around the issue.
According to the DP standard's 0xF0000 register description:
"LTTPR-related registers at DPCD Addresses F0000h through F02FFh are
valid only for DPCD r1.4 (or higher)." While it's unclear if DPCD r1.4
refers to the DPCD_REV or to the
LT_TUNABLE_PHY_REPEATER_FIELD_DATA_STRUCTURE_REV register (tickets filed
at the VESA site to clarify this haven't been addressed), one
possibility is that it's a restriction due to non-compliant monitors
described above. Disabling the non-transparent LTTPR mode for all such
monitors is not a viable solution: the transparent LTTPR mode has its
own issue causing link training failures and this would affect a lot of
monitors in use with DPCD_REV < 1.4. Instead this patch works around
the problem by reading the LTTPR common and PHY cap registers one-by-one
for any monitor with a DPCD_REV < 1.4.
The standard requires the DPCD capabilities to be read after the LTTPR
common capabilities are read, so re-read the DPCD capabilities after
the LTTPR common and PHY caps were read out.
v2:
- Use for instead of a while loop. (Ville)
- Add to code comment the monitor model with the problem.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4531
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220322143844.42616-1-imre.deak@intel.com
This way we finally fix the problem that new resource are
not immediately evict-able after allocation.
That has caused numerous problems including OOM on GDS handling
and not being able to use TTM as general resource manager.
v2: stop assuming in ttm_resource_fini that res->bo is still valid.
v3: cleanup kerneldoc, add more lockdep annotation
v4: consistently use res->num_pages
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321132601.2161-1-christian.koenig@amd.com
There is no "reversed" handling in drm_fb_xrgb8888_to_mono_reversed():
the function just converts from color to grayscale, and reduces the
number of grayscale levels from 256 to 2 (i.e. brightness 0-127 is
mapped to 0, 128-255 to 1). All "reversed" handling is done in the
repaper driver, where this function originated.
Hence make this clear by renaming drm_fb_xrgb8888_to_mono_reversed() to
drm_fb_xrgb8888_to_mono(), and documenting the black/white pixel
mapping.
Fixes: bcf8b616de ("drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-2-geert@linux-m68k.org
Since a HS transmission is composed of an arbitrary number
of bytes that may not be an integer multiple of lanes, some
lanes may run out of data before others.
(Defined in 6.1.3 of mipi_DSI_specification_v.01-02-00)
However, for some DSI RX devices (for example, anx7625),
there is a limitation that packet number should be the same
on all DSI lanes. In other words, they need to end a HS at
the same time.
Because this limitation is for some specific DSI RX devices,
it is more reasonable to put the enable control in these
DSI RX drivers. If DSI TX driver knows the information,
they can adjust the setting for this situation.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-2-rex-bc.chen@mediatek.com
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Improve performance of some fbdev ops, in some cases up to 6x faster.
Core Changes:
- Some small DP fixes.
- Find panels in subnodes of OF devices, and add of_get_drm_panel_display_mode
to retrieve mode.
- Add drm_object_property_get_default_value and use it for resetting
zpos in plane state reset, removing the need for individual drivers
to do it.
- Same for color encoding and color range props.
- Update panic handling todo doc.
- Add todo that format conversion helpers should be sped up similarly to fbdev ops.
Driver Changes:
- Add panel orientation property to simpledrm for quirked panels.
- Assorted small fixes to tiny/repaper, nouveau, stm, omap, ssd130x.
- Add crc support to stm/ltdc.
- Add MIPI DBI compatible SPI driver
- Assorted small fixes to tiny panels and bridge drivers.
- Add AST2600 support to aspeed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/48fabd78-ade9-f80b-c724-13726c7be69e@linux.intel.com
The link_status array was not large enough to read the Adjust Request
Post Cursor2 register, so remove the common helper function to avoid
an OOB read, found with a -Warray-bounds build:
drivers/gpu/drm/drm_dp_helper.c: In function 'drm_dp_get_adjust_request_post_cursor':
drivers/gpu/drm/drm_dp_helper.c:59:27: error: array subscript 10 is outside array bounds of 'const u8[6]' {aka 'const unsigned char[6]'} [-Werror=array-bounds]
59 | return link_status[r - DP_LANE0_1_STATUS];
| ~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/drm_dp_helper.c:147:51: note: while referencing 'link_status'
147 | u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
| ~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Replace the only user of the helper with an open-coded fetch and decode,
similar to drivers/gpu/drm/amd/display/dc/core/dc_link_dp.c.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Fixes: 79465e0ffe ("drm/dp: Add helper to get post-cursor adjustments")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20220105173507.2420910-1-keescook@chromium.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
UAPI Changes:
- Weak parallel submission support for execlists
Minimal implementation of the parallel submission support for
execlists backend that was previously only implemented for GuC.
Support one sibling non-virtual engine.
Core Changes:
- Two backmerges of drm/drm-next for header file renames/changes and
i915_regs reorganization
Driver Changes:
- Add new DG2 subplatform: DG2-G12 (Matt R)
- Add new DG2 workarounds (Matt R, Ram, Bruce)
- Handle pre-programmed WOPCM registers for DG2+ (Daniele)
- Update guc shim control programming on XeHP SDV+ (Daniele)
- Add RPL-S C0/D0 stepping information (Anusha)
- Improve GuC ADS initialization to work on ARM64 on dGFX (Lucas)
- Fix KMD and GuC race on accessing PMU busyness (Umesh)
- Use PM timestamp instead of RING TIMESTAMP for reference in PMU with GuC (Umesh)
- Report error on invalid reset notification from GuC (John)
- Avoid WARN splat by holding RPM wakelock during PXP unbind (Juston)
- Fixes to parallel submission implementation (Matt B.)
- Improve GuC loading status check/error reports (John)
- Tweak TTM LRU priority hint selection (Matt A.)
- Align the plane_vma to min_page_size of stolen mem (Ram)
- Introduce vma resources and implement async unbinding (Thomas)
- Use struct vma_resource instead of struct vma_snapshot (Thomas)
- Return some TTM accel move errors instead of trying memcpy move (Thomas)
- Fix a race between vma / object destruction and unbinding (Thomas)
- Remove short-term pins from execbuf (Maarten)
- Update to GuC version 69.0.3 (John, Michal Wa.)
- Improvements to GT reset paths in GuC backend (Matt B.)
- Use shrinker_release_pages instead of writeback in shmem object hooks (Matt A., Tvrtko)
- Use trylock instead of blocking lock when freeing GEM objects (Maarten)
- Allocate intel_engine_coredump_alloc with ALLOW_FAIL (Matt B.)
- Fixes to object unmapping and purging (Matt A)
- Check for wedged device in GuC backend (John)
- Avoid lockdep splat by locking dpt_obj around set_cache_level (Maarten)
- Allow dead vm to unbind vma's without lock (Maarten)
- s/engine->i915/i915/ for DG2 engine workarounds (Matt R)
- Use to_gt() helper for GGTT accesses (Michal Wi.)
- Selftest improvements (Matt B., Thomas, Ram)
- Coding style and compiler warning fixes (Matt B., Jasmine, Andi, Colin, Gustavo, Dan)
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yg4i2aCZvvee5Eai@jlahtine-mobl.ger.corp.intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Fixed conflicts while applying, using the fixups/drm-intel-gt-next.patch
from drm-rerere's 1f2b1742abdd ("2022y-02m-23d-16h-07m-57s UTC: drm-tip
rerere cache update")]
On contiguous allocation, we round up the size
to the *next* power of 2, implement a function
to free the unused pages after the newly allocate block.
v2(Matthew Auld):
- replace function name 'drm_buddy_free_unused_pages' with
drm_buddy_block_trim
- replace input argument name 'actual_size' with 'new_size'
- add more validation checks for input arguments
- add overlaps check to avoid needless searching and splitting
- merged the below patch to see the feature in action
- add free unused pages support to i915 driver
- lock drm_buddy_block_trim() function as it calls mark_free/mark_split
are all globally visible
v3(Matthew Auld):
- remove trim method error handling as we address the failure case
at drm_buddy_block_trim() function
v4:
- in case of trim, at __alloc_range() split_block failure path
marks the block as free and removes it from the original list,
potentially also freeing it, to overcome this problem, we turn
the drm_buddy_block_trim() input node into a temporary node to
prevent recursively freeing itself, but still retain the
un-splitting/freeing of the other nodes(Matthew Auld)
- modify the drm_buddy_block_trim() function return type
v5(Matthew Auld):
- revert drm_buddy_block_trim() function return type changes in v4
- modify drm_buddy_block_trim() passing argument n_pages to original_size
as n_pages has already been rounded up to the next power-of-two and
passing n_pages results noop
v6:
- fix warnings reported by kernel test robot <lkp@intel.com>
v7:
- modify drm_buddy_block_trim() function doc description
- at drm_buddy_block_trim() handle non-allocated block as
a serious programmer error
- fix a typo
Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-3-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Implemented a function which walk through the order list,
compares the offset and returns the maximum offset block,
this method is unpredictable in obtaining the high range
address blocks which depends on allocation and deallocation.
for instance, if driver requests address at a low specific
range, allocator traverses from the root block and splits
the larger blocks until it reaches the specific block and
in the process of splitting, lower orders in the freelist
are occupied with low range address blocks and for the
subsequent TOPDOWN memory request we may return the low
range blocks.To overcome this issue, we may go with the
below approach.
The other approach, sorting each order list entries in
ascending order and compares the last entry of each
order list in the freelist and return the max block.
This creates sorting overhead on every drm_buddy_free()
request and split up of larger blocks for a single page
request.
v2:
- Fix alignment issues(Matthew Auld)
- Remove unnecessary list_empty check(Matthew Auld)
- merged the below patch to see the feature in action
- add top-down alloc support to i915 driver
Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-2-Arunpravin.PaneerSelvam@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
- Make drm_buddy_alloc a single function to handle
range allocation and non-range allocation demands
- Implemented a new function alloc_range() which allocates
the requested power-of-two block comply with range limitations
- Moved order computation and memory alignment logic from
i915 driver to drm buddy
v2:
merged below changes to keep the build unbroken
- drm_buddy_alloc_range() becomes obsolete and may be removed
- enable ttm range allocation (fpfn / lpfn) support in i915 driver
- apply enhanced drm_buddy_alloc() function to i915 driver
v3(Matthew Auld):
- Fix alignment issues and remove unnecessary list_empty check
- add more validation checks for input arguments
- make alloc_range() block allocations as bottom-up
- optimize order computation logic
- replace uint64_t with u64, which is preferred in the kernel
v4(Matthew Auld):
- keep drm_buddy_alloc_range() function implementation for generic
actual range allocations
- keep alloc_range() implementation for end bias allocations
v5(Matthew Auld):
- modify drm_buddy_alloc() passing argument place->lpfn to lpfn
as place->lpfn will currently always be zero for i915
v6(Matthew Auld):
- fixup potential uaf - If we are unlucky and can't allocate
enough memory when splitting blocks, where we temporarily
end up with the given block and its buddy on the respective
free list, then we need to ensure we delete both blocks,
and no just the buddy, before potentially freeing them
- fix warnings reported by kernel test robot <lkp@intel.com>
v7(Matthew Auld):
- revert fixup potential uaf
- keep __alloc_range() add node to the list logic same as
drm_buddy_alloc_blocks() by having a temporary list variable
- at drm_buddy_alloc_blocks() keep i915 range_overflows macro
and add a new check for end variable
v8:
- fix warnings reported by kernel test robot <lkp@intel.com>
v9(Matthew Auld):
- remove DRM_BUDDY_RANGE_ALLOCATION flag
- remove unnecessary function description
v10:
- keep DRM_BUDDY_RANGE_ALLOCATION flag as removing the flag
and replacing with (end < size) logic fails amdgpu driver load
Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221164552.2434-1-Arunpravin.PaneerSelvam@amd.com
Add support to convert from XR24 to reversed monochrome for drivers that
control monochromatic display panels, that only have 1 bit per pixel.
The function does a line-by-line conversion doing an intermediate step
first from XR24 to 8-bit grayscale and then to reversed monochrome.
The drm_fb_gray8_to_mono_reversed_line() helper was based on code from
drivers/gpu/drm/tiny/repaper.c driver.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214133710.3278506-3-javierm@redhat.com
We'd like panels to be able to add things to debugfs underneath the
connector's directory. Let's plumb it through. A panel will be able to
put things in a "panel" directory under the connector's
directory. Note that debugfs is not ABI and so it's always possible
that the location that the panel gets for its debugfs could change in
the future.
NOTE: this currently only works if you're using a modern
architecture. Specifically the plumbing relies on _both_
drm_bridge_connector and drm_panel_bridge. If you're not using one or
both of these things then things won't be plumbed through.
As a side effect of this change, drm_bridges can also get callbacks to
put stuff underneath the connector's debugfs directory. At the moment
all bridges in the chain have their debugfs_init() called with the
connector's root directory.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.2.Ib0bd5346135cbb0b63006b69b61d4c8af6484740@changeid
