We always allocate two DPLLs (TC and TBT) for TC ports. This
is because we can't know ahead of time wherher we need to put
the PHY into DP-Alt or TBT mode.
However during readout we can obviously only read out the state
of the DPLL that the port is actually using. Thus the state after
readout will not have both DPLLs populated.
We run into problems if during readout the TC port is in DP-Alt
mode, but we then perform a modeset on the port without going
through the full .compute_config() machinery, and during said
modeset the port cannot be switched back into DP-Alt mode and
we need to take the TBT fallback path. Such a modeset can
happen eg. due to cdclk reprogramming.
This wasn't a problem earlier because we did all the DPLL
calculations much later in the modeset. So even if flagged
a modeset very late we'd still have gone through the DPLL
calculations. But now all the DPLL calculations happen much
earlier and so we need to deal with it, or else we'll attempt
a modeset without a DPLL.
To guarantee that we always have both DPLLs fully cal/ulated
for TC ports force a full modeset computation during the
initial commit.
v2: Avoid bitwise operation on bool (Jani)
Call the return variable 'fastset' to convey its meaning
Reported-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: b000abd3b3 ("drm/i915: Do .crtc_compute_clock() earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191236.4194-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit eddb4afcb6)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Commit 00c6cbfd4e ("drm/i915: move pipe_mask and cpu_transcoder_mask
to runtime info") moved the pipe_mask member from struct
intel_device_info to intel_runtime_info, but overlooked some of our
platforms initializing device info .display = {}. This is significant,
as pipe_mask is the single point of truth for a device having a display
or not; the platforms in question left pipe_mask to whatever was set for
the platforms they "inherit" from in the complex macro scheme we have.
Add new NO_DISPLAY macro initializing .__runtime.pipe_mask = 0, which
will cause the device info .display sub-struct to be zeroed in
intel_device_info_runtime_init(). A better solution (or simply audit of
proper use of HAS_DISPLAY() checks) is required before moving forward
with [1].
Also clear all the display related members in runtime info if there's no
display. The latter is a bit tedious, but it's for completeness at this
time, to ensure similar functionality as before.
[1] https://lore.kernel.org/r/dfda1bf67f02ceb07c280b7a13216405fd1f7a34.1660137416.git.jani.nikula@intel.com
Fixes: 00c6cbfd4e ("drm/i915: move pipe_mask and cpu_transcoder_mask to runtime info")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Maarten Lankhort <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916082642.3451961-1-jani.nikula@intel.com
(cherry picked from commit 86570b7b12)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
For delayed BO release i915_ttm_delete_mem_notify()
gets called twice, once with proper bo->resource and
another time with NULL. We shouldn't do anything for
the 2nd time as we already cleaned up the obj once.
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6850
Fixes: ad74457a6b ("drm/i915/dgfx: Release mmap on rpm suspend")
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220920170628.3391-1-nirmoy.das@intel.com
(cherry picked from commit fb78189899)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The ipc_enabled member was supposed to be moved under the display wm
sub-struct, but due to a rebase fail only the new one was added and the
old one was left behind. Finish the job.
Fixes: 70296670f6 ("drm/i915/display: move IPC under display wm sub-struct")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916113850.3712354-1-jani.nikula@intel.com
(cherry picked from commit 4817610400)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
A patch was merged to remove the GuC log size override module
parameters. That patch was broken and caused kernel error messages on
boot in non CONFIG_DEBUG_GUC|GEM builds:
[ 12.085121] i915 0000:00:02.0: [drm] *ERROR* Zero GuC log crash dump size!
[ 12.092035] i915 0000:00:02.0: [drm] *ERROR* Zero GuC log debug size!
So fit it.
Fixes: f54e515c91 ("drm/i915/guc: Remove log size module parameters")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913010929.2734885-2-John.C.Harrison@Intel.com
(cherry picked from commit 01f0ce3e85)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Michael Weiß says:
====================
net: openvswitch: metering and conntrack in userns
Currently using openvswitch in a non-initial user namespace, e.g., an
unprivileged container, is possible but without metering and conntrack
support. This is due to the restriction of the corresponding Netlink
interfaces to the global CAP_NET_ADMIN.
This simple patches switch from GENL_ADMIN_PERM to GENL_UNS_ADMIN_PERM
in several cases to allow this also for the unprivileged container
use case.
We tested this for unprivileged containers created by the container
manager of GyroidOS (gyroidos.github.io). However, for other container
managers such as LXC or systemd which provide unprivileged containers
this should be apply equally.
====================
Link: https://lore.kernel.org/r/20220923133820.993725-1-michael.weiss@aisec.fraunhofer.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to the previous commit, the Netlink interface of the OVS
conntrack module was restricted to global CAP_NET_ADMIN by using
GENL_ADMIN_PERM. This is changed to GENL_UNS_ADMIN_PERM to support
unprivileged containers in non-initial user namespace.
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Netlink interface for metering was restricted to global CAP_NET_ADMIN
by using GENL_ADMIN_PERM. To allow metring in a non-inital user namespace,
e.g., a container, this is changed to GENL_UNS_ADMIN_PERM.
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
CNTPCT_LO and CNTVCT_LO are defined by mistake in commit '8b82c4f883a7',
so fix them according to the Arm ARM DDI 0487I.a, Table I2-4
"CNTBaseN memory map" as follows:
Offset Register Type Description
0x000 CNTPCT[31:0] RO Physical Count register.
0x004 CNTPCT[63:32] RO
0x008 CNTVCT[31:0] RO Virtual Count register.
0x00C CNTVCT[63:32] RO
Fixes: 8b82c4f883 ("clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL")
Cc: stable@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Yang Guo <guoyang2@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20220927033221.49589-1-zhangshaokun@hisilicon.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Simplify pci-ftpci100.c driver code and use new PCI_CONF1_ADDRESS() macro
for accessing PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Lot of PCI and PCIe controllers are using standard Config Address for PCI
Configuration Mechanism #1 (as defined in PCI Local Bus Specification) or
its extended version.
So introduce new macros PCI_CONF1_ADDRESS() and PCI_CONF1_EXT_ADDRESS() in
include file drivers/pci/pci.h which can be suitable for PCI and PCIe
controllers which uses this type of access to PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The socket 2 bind the addr in use, bind should fail with EADDRINUSE. So
if bind success or errno != EADDRINUSE, testcase should be failed.
Fixes: 3ca8e40299 ("soreuseport: BPF selection functional test")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Link: https://lore.kernel.org/r/1663916557-10730-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The UAS mode of Hiksemi USB_HDD is reported to fail to work on several
platforms with the following error message, then after re-connecting the
device will be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901185-21067-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UAS mode of Hiksemi is reported to fail to work on several platforms
with the following error message, then after re-connecting the device will
be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901173-21020-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sink only devices do not have any source capabilities, so
the driver should not warn about that. Also DRP (Dual Role
Power) capable devices, such as USB Type-C docking stations,
do not return any source capabilities unless they are
plugged to a power supply themselves.
Fixes: 1f4642b72b ("usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922145924.80667-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume()
state") introduced a WARN() on resume from system sleep if a PHY is not
in PHY_HALTED state.
Commit 6dbe852c37 ("net: phy: Don't WARN for PHY_READY state in
mdio_bus_phy_resume()") added an exemption for PHY_READY state from
the WARN().
It turns out PHY_UP state needs to be exempted as well because the
following may happen on suspend:
mdio_bus_phy_suspend()
phy_stop_machine()
phydev->state = PHY_UP # if (phydev->state >= PHY_UP)
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/netdev/2b1a1588-505e-dff3-301d-bfc1fb14d685@samsung.com/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/8128fdb51eeebc9efbf3776a4097363a1317aaf1.1663905575.git.lukas@wunner.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This includes a single fix from Mario that resets the plug event delay
back to the USB4 spec value.
This has been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=m6dT
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
"thunderbolt: Fix for v6.0 final
This includes a single fix from Mario that resets the plug event delay
back to the USB4 spec value.
This has been in linux-next with no reported issues."
* tag 'thunderbolt-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Explicitly reset plug events delay back to USB4 spec value
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested.
Reported-by: syzbot+79832d33eb89fb3cd092@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220922134847.1101921-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922133323.2135494-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922133323.2135494-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE helper macro to simplify the code.
No functional change.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922142505.3248167-1-liushixin2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports the following error:
drivers/usb/cdns3/cdns3-plat.c:113 cdns3_plat_probe() warn:
platform_get_irq() does not return zero
From the document, platform_get_irq_byname_optional only returns
non-zero value, and negative value on failure.
Fix this by removing the zero value checking.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220926135922.24541-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use skb_put_data() instead of skb_put() and memcpy(), which is clear.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220927024344.14352-1-shangxiaojing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-6-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-5-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-4-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-3-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-2-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220922134806.2204579-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135708.2212249-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135228.2206755-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922123951.2004328-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success
handling") moved the per-link setup out of ieee80211_assoc_success() into a
new function ieee80211_assoc_config_link() but missed to remove the unlock
of 'sta_mtx' in case of HE capability/operation missing on HE AP, which
leads to a double unlock:
ieee80211_assoc_success() {
...
ieee80211_assoc_config_link() {
...
if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
(!elems->he_cap || !elems->he_operation)) {
mutex_unlock(&sdata->local->sta_mtx);
...
}
...
}
...
mutex_unlock(&sdata->local->sta_mtx);
...
}
Fixes: 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success handling")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Link: https://lore.kernel.org/r/20220925143420.784975-1-rafaelmendsr@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 98b0b46746 ("wifi: mac80211: mlme: use correct link_sta")
switched to link station instead of deflink and added some checks to do
that, which are done with the 'sta_mtx' mutex held. However, the error
path of these checks does not unlock 'sta_mtx' before returning.
Fixes: 98b0b46746 ("wifi: mac80211: mlme: use correct link_sta")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Link: https://lore.kernel.org/r/20220924184042.778676-1-rafaelmendsr@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During our testing of WFM200 module over SDIO on i.MX6Q-based platform,
we discovered a memory corruption on the system, tracing back to the wfx
driver. Using kfence, it was possible to trace it back to the root
cause, which is hw->max_rates set to 8 in wfx_init_common,
while the maximum defined by IEEE80211_TX_TABLE_SIZE is 4.
This causes array out-of-bounds writes during updates of the rate table,
as seen below:
BUG: KFENCE: memory corruption in kfree_rcu_work+0x320/0x36c
Corrupted memory at 0xe0a4ffe0 [ 0x03 0x03 0x03 0x03 0x01 0x00 0x00
0x02 0x02 0x02 0x09 0x00 0x21 0xbb 0xbb 0xbb ] (in kfence-#81):
kfree_rcu_work+0x320/0x36c
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c
0x0
kfence-#81: 0xe0a4ffc0-0xe0a4ffdf, size=32, cache=kmalloc-64
allocated by task 297 on cpu 0 at 631.039555s:
minstrel_ht_update_rates+0x38/0x2b0 [mac80211]
rate_control_tx_status+0xb4/0x148 [mac80211]
ieee80211_tx_status_ext+0x364/0x1030 [mac80211]
ieee80211_tx_status+0xe0/0x118 [mac80211]
ieee80211_tasklet_handler+0xb0/0xe0 [mac80211]
tasklet_action_common.constprop.0+0x11c/0x148
__do_softirq+0x1a4/0x61c
irq_exit+0xcc/0x104
call_with_stack+0x18/0x20
__irq_svc+0x80/0xb0
wq_worker_sleeping+0x10/0x100
wq_worker_sleeping+0x10/0x100
schedule+0x50/0xe0
schedule_timeout+0x2e0/0x474
wait_for_completion+0xdc/0x1ec
mmc_wait_for_req_done+0xc4/0xf8
mmc_io_rw_extended+0x3b4/0x4ec
sdio_io_rw_ext_helper+0x290/0x384
sdio_memcpy_toio+0x30/0x38
wfx_sdio_copy_to_io+0x88/0x108 [wfx]
wfx_data_write+0x88/0x1f0 [wfx]
bh_work+0x1c8/0xcc0 [wfx]
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c 0x0
After discussion on the wireless mailing list it was clarified
that the issue has been introduced by:
commit ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
and fix shall be in minstrel_ht_update_rates in rc80211_minstrel_ht.c.
Fixes: ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
Link: https://lore.kernel.org/all/12e5adcd-8aed-f0f7-70cc-4fb7b656b829@camlingroup.com/
Link: https://lore.kernel.org/linux-wireless/20220915131445.30600-1-lech.perczak@camlingroup.com/
Cc: Jérôme Pouiller <jerome.pouiller@silabs.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Seiderer <ps.report@gmx.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Krzysztof Drobiński <krzysztof.drobinski@camlingroup.com>,
Signed-off-by: Paweł Lenkow <pawel.lenkow@camlingroup.com>
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Peter Seiderer <ps.report@gmx.net>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
changed ieee80211_tx_control_port() to aways call
__ieee80211_select_queue() without checking local->hw.queues.
__ieee80211_select_queue() returns a queue-id between 0 and 3, which means
that now ieee80211_tx_control_port() may end up setting the queue-mapping
for a skb to a value higher then local->hw.queues if local->hw.queues
is less then 4.
Specifically this is a problem for ralink rt2500-pci cards where
local->hw.queues is 2. There this causes rt2x00queue_get_tx_queue() to
return NULL and the following error to be logged: "ieee80211 phy0:
rt2x00mac_tx: Error - Attempt to send packet over invalid queue 2",
after which association with the AP fails.
Other callers of __ieee80211_select_queue() skip calling it when
local->hw.queues < IEEE80211_NUM_ACS, add the same check to
ieee80211_tx_control_port(). This fixes ralink rt2500-pci and
similar cards when less then 4 tx-queues no longer working.
Fixes: 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
Cc: Markus Theil <markus.theil@tu-ilmenau.de>
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220918192052.443529-1-hdegoede@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure local->queue_stop_reasons and vif.txqs_stopped stay in sync.
When a new vif is created the queues may end up in an inconsistent state
and be inoperable:
Communication not using iTXQ will work, allowing to e.g. complete the
association. But the 4-way handshake will time out. The sta will not
send out any skbs queued in iTXQs.
All normal attempts to start the queues will fail when reaching this
state.
local->queue_stop_reasons will have marked all queues as operational but
vif.txqs_stopped will still be set, creating an inconsistent internal
state.
In reality this seems to be race between the mac80211 function
ieee80211_do_open() setting SDATA_STATE_RUNNING and the wake_txqs_tasklet:
Depending on the driver and the timing the queues may end up to be
operational or not.
Cc: stable@vger.kernel.org
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220915130946.302803-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_txq_purge() calls fq_tin_reset() and
ieee80211_purge_tx_queue(); Both are then calling
ieee80211_free_txskb(). Which can decide to TX the skb again.
There are at least two ways to get a deadlock:
1) When we have a TDLS teardown packet queued in either tin or frags
ieee80211_tdls_td_tx_handle() will call ieee80211_subif_start_xmit()
while we still hold fq->lock. ieee80211_txq_enqueue() will thus
deadlock.
2) A variant of the above happens if aggregation is up and running:
In that case ieee80211_iface_work() will deadlock with the original
task: The original tasks already holds fq->lock and tries to get
sta->lock after kicking off ieee80211_iface_work(). But the worker
can get sta->lock prior to the original task and will then spin for
fq->lock.
Avoid these deadlocks by not sending out any skbs when called via
ieee80211_free_txskb().
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20220915124120.301918-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use skb_put_data() instead of skb_put() and memcpy(), which is shorter
and clear. Drop the tmp variable that is not needed any more.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20220927024050.13556-1-shangxiaojing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All remaining functions in hal/odm_RegConfig8188E.c are only used
in hal/HalHWImg8188E_BB.c. Make them static and remove the now empty
file hal/odm_RegConfig8188E.c and the header odm_RegConfig8188E.h.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Link: https://lore.kernel.org/r/20220926173243.8767-4-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function odm_ConfigRF_RadioA_8188E() is only used in
HalHWImg8188E_RF.c. Make it static.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Link: https://lore.kernel.org/r/20220926173243.8767-3-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä
Jani Nikula
Nirmoy Das
John Harrison
Leon Romanovsky
Paolo Abeni
Michael Weiß
Yang Guo
Gao Xiang
Krishna chaitanya chundru
Pali Rohár
Wang Yufen
Hongling Zeng
Patrice Chotard
Heikki Krogerus
Lukas Wunner
Greg Kroah-Hartman
Junxiao Chang
Dongliang Mu
Yang Yingliang
Liu Shixin
Shang XiaoJing
Rafael Mendonca
Paweł Lenkow
Hans de Goede
Alexander Wetzel
Michael Straube