Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Qualcomm driver updates for v5.6
* SCM major refactoring and cleanup
* Properly flag active only power domains as active only
* Add SC7180 and SM8150 RPMH power domains
* Return EPROBE_DEFER from QMI if packet family is not yet available
* tag 'qcom-drivers-for-5.6' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (27 commits)
firmware: qcom_scm: Dynamically support SMCCC and legacy conventions
firmware: qcom_scm: Remove thin wrappers
firmware: qcom_scm: Order functions, definitions by service/command
firmware: qcom_scm-32: Add device argument to atomic calls
firmware: qcom_scm-32: Create common legacy atomic call
firmware: qcom_scm-32: Move SMCCC register filling to qcom_scm_call
firmware: qcom_scm-32: Use qcom_scm_desc in non-atomic calls
firmware: qcom_scm-32: Add funcnum IDs
firmware: qcom_scm-32: Use SMC arch wrappers
firmware: qcom_scm-64: Improve SMC convention detection
firmware: qcom_scm-64: Move SMC register filling to qcom_scm_call_smccc
firmware: qcom_scm-64: Add SCM results struct
firmware: qcom_scm-64: Move svc/cmd/owner into qcom_scm_desc
firmware: qcom_scm-64: Make SMC macros less magical
firmware: qcom_scm: Remove unused qcom_scm_get_version
firmware: qcom_scm: Apply consistent naming scheme to command IDs
firmware: qcom_scm: Rename macros and structures
soc: qcom: rpmhpd: Set 'active_only' for active only power domains
firmware: scm: Add stubs for OCMEM and restore_sec_cfg_available
dt-bindings: power: rpmpd: Convert rpmpd bindings to yaml
...
Link: https://lore.kernel.org/r/20200113204405.GD3325@yoga
Signed-off-by: Olof Johansson <olof@lixom.net>
This is our usual set of DT patches for the Allwinner SoCs.
It's fairly big this time, but the highlights are:
- Enable cpufreq and CPU thermal throttling on the A64
- CLK_CPUX macro usage removed (changed from first pull request)
- CSI0 support on the R40
- CSI1 support on the A10 and A20
- SPI support on the R40
- PMU support on the H3, H5, H6 and R40
- MIPI-DSI support on the A64
- PWM support on the H6
- Thermal sensor on the A64, A83t, H3, H5, H6 and R40
- More DT schemas fixes and conversions
- New boards: LibreComputer ALL-H5-CC H5, LibreComputer ALL-H3-IT H5,
Pine64 H64 Model B, Neutis N5H3
* tag 'sunxi-dt-for-5.6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (52 commits)
arm64: dts: allwinner: a64: enable DVFS
arm64: dts: allwinner: a64: add dtsi with CPU operating points
arm64: dts: allwinner: a64: add cooling maps and thermal tripping points
arm64: dts: allwinner: a64: add CPU clock to CPU0-3 nodes
arm64: dts: allwinner: sun50i-a64: Use macros for newly exported clocks
ARM: dts: sunxi: Use macros for references to CCU clocks
arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board
ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes
arm64: dts: allwinner: a64: pinebook: Fix lid wakeup
ARM: dts: sun8i: r40: Add device node for CSI0
ARM: dts: sun7i: Add CSI1 controller and pinmux options
ARM: dts: sun4i: Add CSI1 controller and pinmux options
ARM: dts: sunxi: Add missing LVDS resets and clocks
ARM: dts: sun8i: r40: Use tcon top clock index macros
ARM: dts: sun8i: R40: Add PMU node
ARM: dts: sun8i: R40: Upgrade GICC reg size to 8K
arm64: dts: allwinner: h6: Add thermal sensor and thermal zones
ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board
arm64: dts: allwinner: a64: Add MIPI DSI pipeline
arm64: dts: allwinner: a64: Add thermal sensors and thermal zones
...
Link: https://lore.kernel.org/r/20200113095555.GA29848@wens.csie.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Add driver for Microchip PIT64B timer. Timer could be used in continuous
mode or oneshot mode. The hardware has 2x32 bit registers for period
emulating a 64 bit timer. The LSB_PR and MSB_PR registers are used to
set the period value (compare value). TLSB and TMSB keeps the current
value of the counter. After a compare the TLSB and TMSB register resets.
The driver uses PIT64B timer for clocksource or clockevent. First
requested timer would be registered as clockevent, second one would be
registered as clocksource. Individual PIT64B hardware resources were
used for clocksource and clockevent to be able to support high resolution
timers with this hardware implementation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1576235962-30123-3-git-send-email-claudiu.beznea@microchip.com
Add the compatible enum entries for Gateworks Ventana boards.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
New boards are the Radxa Rock Pi N10 using the VMARC SOM and Dalang
carrier board, separate versions for the two rockpro64 hardware revisions
which switched a pin between revisions. The rockpro64 also got
bluetooth support now.
The px30 got a lot of attention with dsi, gpu and thermal support.
Similarly the rk3399-roc-pc board also got attention with mtd flash,
sdr104 mode, hdmi sound, gpu and a lot of other smaller improvements.
Other than that there is a new gpu-cooling device for rk3399 a cpu
idle-state for rk3328 and more small improvements across a number
of boards.
* tag 'v5.6-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (37 commits)
arm64: dts: rockchip: Enable mp8859 regulator on rk3399-roc-pc
arm64: dts: rockchip: rk3399-hugsun-x99: remove supports-sd and supports-emmc options
arm64: dts: rockchip: rk3399-firefly: remove num-slots from &sdio0 node
arm64: dts: rockchip: Add PX30 LVDS
arm64: dts: rockchip: add dsi controller for px30
arm64: dts: rockchip: Add PX30 DSI DPHY
arm64: dts: rockchip: Add RK3328 idle state
arm64: dts: rockchip: remove identical &uart0 node from rk3368-lion-haikou
arm64: dts: rockchip: Add Radxa Rock Pi N10 initial support
ARM: dts: rockchip: Add Radxa Dalang Carrier board
arm64: dts: rockchip: Add VMARC RK3399Pro SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N10 binding
arm64: dts: rockchip: hook up bluetooth at uart0 on rockpro64
arm64: dts: rockchip: enable wifi module at sdio0 on rockpro64
arm64: dts: rockchip: split rk3399-rockpro64 for v2 and v2.1 boards
arm64: dts: rockchip: enable the gpu on px30-evb
arm64: dts: rockchip: add the gpu for px30
dt-bindings: gpu: mali-bifrost: Add Rockchip PX30
arm64: dts: rockchip: Add GPU cooling device for RK3399
arm64: dts: rockchip: Add regulators for PCIe for Radxa Rock Pi 4 board
...
Link: https://lore.kernel.org/r/5115625.yBEeHQkg2z@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:
- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed
Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Update PSCI DT bindings to allow to represent idle states for CPUs and the
CPU topology, by using a hierarchical layout. Primarily this is done by
re-using the existing DT bindings for PM domains [1] and for PM domain idle
states [2].
Let's also add an example into the document for the PSCI DT bindings, to
clearly show the new hierarchical based layout. The currently supported
flattened layout, is already described in the ARM idle states bindings [3],
so let's leave that as is.
[1] Documentation/devicetree/bindings/power/power_domain.txt
[2] Documentation/devicetree/bindings/power/domain-idle-state.txt
[3] Documentation/devicetree/bindings/arm/idle-states.txt
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.
The board features:
- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver
Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The lx2160a board compatibles "fsl,lx2160a-qds" and "fsl,lx2160a-rdb"
have been in use. Let's document them.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The older Allwinner SoCs have an MBUS controller that is used by Linux,
with a matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the ML-AHB bus bindings to DT schema format using json-schema
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 syscon binding to DT schema format using json-schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
While my email address has changed for a while, all the schemas I
contributed still have the old one unfortunately. Update it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
Add an entry for the Embedded Artists i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.
The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The current sun50i-h6-pine-h64 DT does not specify which model (A or B)
it supports.
When this file was created, only modelA was existing, but now both model
exists and with the time, this DT drifted to support the model B since it is
the most common one.
Furtheremore, some part of the model A does not work with it like ethernet and
HDMI connector (as confirmed by Jernej on IRC).
So it is time to settle the issue, and the easiest way was to state that
this DT is for model B.
Easiest since only a small name changes is required.
Doing the opposite (stating this file is for model A) will add changes (for
ethernet and HDMI) and so, will break too many setup.
But as asked by the maintainer this patch state this file is for model A.
In the process this patch adds the missing compoments to made it work on
model A.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
