Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add battery internal resistance temperature table support
Drivers:
- sc27xx: Optimize the battery resistance with measuring temperature
- max17042-battery: Add MAX17055 support
- bq25890-charger: Add support of BQ25892 and BQ25896 chips
- misc fixes"
* tag 'for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (44 commits)
power: supply: ipaq_micro_battery: remove unneeded semicolon
power: supply: bq25890_charger: fix incorrect error return when bq25890_field_read fails
power: supply: axp20x_usb_power: Only poll while offline
power: supply: axp20x_usb_power: Add wakeup control
power: supply: axp20x_usb_power: Allow offlining
power: supply: axp20x_usb_power: Use a match structure
power: suppy: ucs1002: Make the symbol 'ucs1002_regulator_enable' static
power: reset: at91-poweroff: use proper master clock register offset
power: reset: at91-poweroff: introduce struct shdwc_reg_config
power: supply: bq25890_charger: Add DT and I2C ids for all supported chips
dt-bindings: Add new chips to bq25890 binding documentation
power: supply: bq25890_charger: Add support of BQ25892 and BQ25896 chips
power: supply: core: Update sysfs-class-power ABI document
power: supply: sbs-battery: Fix a signedness bug in sbs_get_battery_capacity()
power: supply: ltc2941-battery-gauge: fix use-after-free
power: supply: max17040: Correct IRQ wake handling
power: supply: axp20x_usb_power: Remove unused device_node
power: supply: axp20x_ac_power: Add wakeup control
power: supply: axp20x_ac_power: Allow offlining
power: supply: axp20x_ac_power: Fix reporting online status
...
arm64: soc: ZynqMP SoC changes for v5.6
- Extend firmware interface for feature checking
- Use mailbox for communication with firmware for power management
* tag 'zynqmp-soc-for-v5.6' of https://github.com/Xilinx/linux-xlnx:
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: firmware: xilinx: Add support for feature check
Link: https://lore.kernel.org/r/f6fb26f8-b00d-a3e8-bf7d-c7ff2a8483b1@monstr.eu
Signed-off-by: Olof Johansson <olof@lixom.net>
Add bq25892, bq25895 and bq25896 to list of supported device IDs in the
bq25890 DT binding document.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Documentation of max17040 based fuel gauge characteristics.
For configure low level state of charge threshold alert signaled from
max17043/max17044 we add "maxim,alert-low-soc-level" property.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the battery internal resistance can be changed as the temperature
changes, thus add one table to describe the battery resistance percent
in different temperatures to get a accurate battery internal resistance.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Pull Devicetree updates from Rob Herring:
- DT schemas for PWM, syscon, power domains, SRAM, syscon-reboot,
syscon-poweroff, renesas-irqc, simple-pm-bus, renesas-bsc, pwm-rcar,
Renesas tpu, at24 eeprom, rtc-sh, Allwinner PS/2, sharp,ld-d5116z01b
panel, Arm SMMU, max77650, Meson CEC, Amlogic canvas and DWC3 glue,
Allwinner A10 mUSB and CAN, TI Davinci MDIO, QCom QCS404
interconnect, Unisoc/Spreadtrum SoCs and UART
- Convert a bunch of Samsung bindings to DT schema
- Convert a bunch of ST stm32 bindings to DT schema
- Realtek and Exynos additions to Arm Mali bindings
- Fix schema errors in RiscV CPU schema
- Various schema fixes from improved meta-schema checks
- Improve the handling of 'dma-ranges' and in particular fix DMA mask
setup on PCI bridges
- Fix a memory leak in add_changeset_property() and DT unit tests.
- Several documentation improvements for schema validation
- Rework build rules to improve schema validation errors
- Color output for dtx_diff
* tag 'devicetree-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (138 commits)
libfdt: define INT32_MAX and UINT32_MAX in libfdt_env.h
dt-bindings: arm: Remove leftover axentia.txt
of: unittest: fix memory leak in attach_node_and_children
of: overlay: add_changeset_property() memory leak
dt-bindings: interrupt-controller: arm,gic-v3: Add missing type to interrupt-partition-* nodes
dt-bindings: firmware: ixp4xx: Drop redundant minItems/maxItems
dt-bindings: power: Rename back power_domain.txt bindings to fix references
dt-bindings: i2c: stm32: Migrate i2c-stm32 documentation to yaml
dt-bindings: mtd: Convert stm32 fmc2-nand bindings to json-schema
dt-bindings: remoteproc: convert stm32-rproc to json-schema
dt-bindings: mailbox: convert stm32-ipcc to json-schema
dt-bindings: mfd: Convert stm32 low power timers bindings to json-schema
dt-bindings: interrupt-controller: Convert stm32-exti to json-schema
dt-bindings: crypto: Convert stm32 HASH bindings to json-schema
dt-bindings: rng: Convert stm32 RNG bindings to json-schema
dt-bindings: pwm: Convert Samsung PWM bindings to json-schema
dt-bindings: pwm: Convert PWM bindings to json-schema
dt-bindings: serial: Add a new compatible string for SC9863A
dt-bindings: serial: Convert sprd-uart to json-schema
dt-bindings: arm: Add bindings for Unisoc SC9863A
...
With split of power domain controller bindings to power-domain.yaml,
the consumer part was renamed to power-domain.txt breaking the
references. Undo the renaming.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 5279a3d8be ("dt-bindings: power: Convert Generic Power Domain bindings to json-schema")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Samsung Exynos Soc Power Domain bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the binding document for MAX77650 charger module to YAML.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Change the indentation of examples used in json-schema bindings from two
to four spaces as this makes the code easier to read and seems to be
preferred in other files.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Sebastian Reichel <sre@kernel.org> # for power/reset
Signed-off-by: Rob Herring <robh@kernel.org>
The MSM8956/76 SoCs have two main voltage-level power domains, VDD_CX
and VDD_MX, which also have their own voltage-floor-level (VFL)
corner.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Convert the Syscon poweroff bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the Syscon reboot bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add the bindings for the Amlogic Everything-Else power domains,
controlling the Everything-Else peripherals power domains.
The bindings targets the Amlogic G12A and SM1 compatible SoCs,
support for earlier SoCs will be added later.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
This immutable branch contains the changes required for OLPC
1.75 battery, which touches x86 and power-supply and is based
on v5.1-rc1.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds the "x-powers,axp813-usb-power-supply" to the list of
compatibles for AXP20X VBUS power supply driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Amlogic G12A has a slighly different Power Control, but uses the
same address space and sysctrl registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There never was a device called LTC3651, it always was just LT3651.
This circumstance makes it pretty difficult to identify what this
driver is meant to control.channges since
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make the syscon-reboot driver accept value and mask instead of
just value.
Prior to this patch, the property name for the value was 'mask'. If
only the mask property is defined on a node, maintain compatibility
by using it as the value.
This patch is based on commit
f2c199db47 ("power: reset: syscon-poweroff: add a mask property")
and does the same change for the syscon-reboot driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull power supply and reset updates from Sebastian Reichel:
"Nothing too fancy in the power-supply subsystem this time. There are
less patches than usual, since I did not have enough time to review
them in time. The good news is, that all patches have been in
linux-next for more than two weeks and there are no complicated
cross-subsystem patchsets this time!
Summary:
- at91-reset: add sam9x60 support
- sc27xx: improve capacity logic
- goldfish_battery: enhance driver by adding many new properties
- isp1704: drop platform data and migrate to gpiod
- misc small fixes and improvements"
* tag 'for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (25 commits)
power: reset: at91-reset: add support for sam9x60 SoC
dt-bindings: arm: atmel: add new sam9x60 reset controller binding
dt-bindings: arm: atmel: add missing samx7 to reset controller
max17042_battery: fix potential use-after-free on device remove
power: supply: core: Add a field to support battery max voltage
dt-bindings: power: supply: Add voltage-max-design-microvolt property
bq27x00: use cached flags
power: supply: ds2782: fix possible use-after-free on remove
power: supply: bq25890: show max charge current/voltage as configured
power: supply: sc27xx: Fix capacity saving function
power: supply: sc27xx: Fix the incorrect formula when converting capacity to coulomb counter
power: supply: sc27xx: Add one property to read charge voltage
dt-bindings: power: sc27xx: Add one IIO channel to read charge voltage
drivers: power: supply: goldfish_battery: Add support for reading more properties
power: supply: charger-manager: Fix trivial language typos
cpcap-charger: generate events for userspace
power: supply: remove some duplicated includes
power: twl4030: fix a missing check of return value
drivers: power: supply: goldfish_battery: Use tabs for alignment
drivers: power: supply: goldfish_battery: Fix alignment
...
