Changing pixel clock source without having this clock source enabled
will block the timing engine and the next operations after (in this case
setting ATMEL_HLCDC_CFG(5) settings in atmel_hlcdc_crtc_mode_set_nofb()
will fail). It is recomended (although in datasheet this is not present)
to actually enabled pixel clock source before doing any changes on timing
enginge (only SAM9X60 datasheet specifies that the peripheral clock and
pixel clock must be enabled before using LCD controller).
Fixes: 1a396789f6 ("drm: add Atmel HLCDC Display Controller support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Link: https://patchwork.freedesktop.org/patch/msgid/1576672109-22707-3-git-send-email-claudiu.beznea@microchip.com
Revert changes done in commit f6ec948309 ("drm/i915: extend audio
CDCLK>=2*BCLK constraint to more platforms"). Audio drivers
communicate with i915 over HDA bus multiple times during system
boot-up and each of these transactions result in matching
get_power/put_power calls to i915, and depending on the platform,
a modeset change causing visible flicker.
GLK is the only platform with minimum CDCLK significantly lower
than BCLK, and thus for GLK setting a higher CDCLK is mandatory.
For other platforms, minimum CDCLK is close but below 2*BCLK
(e.g. on ICL, CDCLK=176.4kHz with BCLK=96kHz). Spec-wise the constraint
should be set, but in practise no communication errors have been
reported and the downside if set is the flicker observed at boot-time.
Revert to old behaviour until better mechanism to manage
probe-time clocks is available.
The full CDCLK>=2*BCLK constraint is still enforced at pipe
enable time in intel_crtc_compute_min_cdclk().
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/913
Fixes: f6ec948309 ("drm/i915: extend audio CDCLK>=2*BCLK constraint to more platforms")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231140007.31728-1-kai.vehmanen@linux.intel.com
Adding the pitch alignment as an argument to
drm_gem_vram_fill_create_dumb() allows to align scanlines to certain
offsets. A value of 0 disables scanline pitches.
v3:
* only do power-of-2 test if pitch_align given; fails otherwise
* mgag200: call drm_gem_vram_fill_create_dumb() with pitch_align
v2:
* split of patch from related hibmc changes
* test if scanline pitch is power of 2
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203083819.6643-4-tzimmermann@suse.de
Requested, and we need v5.5-rc1 backported as our current branch is still based on v5.4.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Base on the somewhat similar Rocktech driver but adapted for
panel-specific init of the XPP055C272.
changes in v5:
- drop error message when backlight not found, no other panel
does that and if needed it should live in drm_panel_of_backlight
changes in v4:
none
changes in v3:
- remove wrong negative sync flags from display-mode to fix a display
artifact of the output getting move a tiny bit to the right
changes in v2:
- move to drm-panel-internal backlight handling (Sam)
- adapt to changes that happened to drm_panel structs+functions (Sam)
- sort includes (Sam)
- drop unnecessary DRV_NAME constant (Sam)
- do mipi_dsi_dcs_exit_sleep_mode and mipi_dsi_dcs_set_display_on
in panel prepare (not init_sequence) to keep symmetric (Sam)
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224112907.30758-3-heiko@sntech.de
[Why]
According to DP spec, it should shift left 4 digits for NO_STOP_BIT
in REMOTE_I2C_READ message. Not 5 digits.
In current code, NO_STOP_BIT is always set to zero which means I2C
master is always generating a I2C stop at the end of each I2C write
transaction while handling REMOTE_I2C_READ sideband message. This issue
might have the generated I2C signal not meeting the requirement. Take
random read in I2C for instance, I2C master should generate a repeat
start to start to read data after writing the read address. This issue
will cause the I2C master to generate a stop-start rather than a
re-start which is not expected in I2C random read.
[How]
Correct the shifting value of NO_STOP_BIT for DP_REMOTE_I2C_READ case in
drm_dp_encode_sideband_req().
Changes since v1:(https://patchwork.kernel.org/patch/11312667/)
* Add more descriptions in commit and cc to stable
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200103055001.10287-1-Wayne.Lin@amd.com
On Bay Trail devices the MIPI power on/off sequences for DSI LCD panels
do not control the LCD panel- and backlight-enable GPIOs. So far, when
the VBT indicates we should use the SoC for backlight control, we have
been relying on these GPIOs being configured as output and driven high by
the Video BIOS (GOP) when it initializes the panel.
This does not work when the device is booted with a HDMI monitor connected
as then the GOP will initialize the HDMI instead of the panel, leaving the
panel black, even though the i915 driver tries to output an image to it.
Likewise on some device-models when the GOP does not initialize the DSI
panel it also leaves the mux of the PWM0 pin in generic GPIO mode instead
of muxing it to the PWM controller.
This commit makes the DSI code control the SoC GPIOs for panel- and
backlight-enable on BYT, when the VBT indicates the SoC should be used
for backlight control. It also ensures that the PWM0 pin is muxed to the
PWM controller in this case.
This fixes the LCD panel not lighting up on various devices when booted
with a HDMI monitor connected. This has been tested to fix this on the
following devices:
Peaq C1010
Point of View MOBII TAB-P800W
Point of View MOBII TAB-P1005W
Terra Pad 1061
Yours Y8W81
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-6-hdegoede@redhat.com
Move the Crystal Cove PMIC panel GPIO lookup-table from
drivers/mfd/intel_soc_pmic_core.c to the i915 driver.
The moved looked-up table is adding a GPIO lookup to the i915 PCI
device and the GPIO subsys allows only one lookup table per device,
The intel_soc_pmic_core.c code only adds lookup-table entries for the
PMIC panel GPIO (as it deals only with the PMIC), but we also need to be
able to access some GPIOs on the SoC itself, which requires entries for
these GPIOs in the lookup-table.
Since the lookup-table is attached to the i915 PCI device it really
should be part of the i915 driver, this will also allow us to extend
it with GPIOs from other sources when necessary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-5-hdegoede@redhat.com
When the LCD has not been turned on by the firmware/GOP, because e.g. the
device was booted with an external monitor connected over HDMI, we should
not turn on the panel-enable GPIO when we request it.
Turning on the panel-enable GPIO when we request it, means we turn it on
too early in the init-sequence, which causes some panels to not correctly
light up.
This commits adds a panel_is_on parameter to intel_dsi_vbt_gpio_init()
and makes intel_dsi_vbt_gpio_init() set the initial GPIO value accordingly.
This fixes the panel not lighting up on a Thundersoft TST168 tablet when
booted with an external monitor connected over HDMI.
Changes in v2:
- Call intel_dsi_get_hw_state() to check if the panel is on instead of
relying on the current_mode pointer
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216205122.1850923-4-hdegoede@redhat.com
