In order to support authentication of equals peers,
need to save RX Broadcast key per peer (on top of 1 TX broadcast key
and unicast key per peer).
Signed-off-by: Maital Hahn <maitalm@ti.com>
Acked-by: Guy Mishol <guym@ti.com>
Signed-off-by: Hari Nagalla <hnagalla@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We set WL1271_FLAG_IRQ_RUNNING in the beginning of wlcore_irq(), but clear
it before interrupt handling is done in wlcore_irq_locked().
Let's move the clearing to the end of wlcore_irq() where it gets set,
and remove the old comments about hardirq. That's no longer the case as
we're using request_threaded_irq().
Note that the WL1271_FLAG_IRQ_RUNNING should never race between the
interrupt handler and wlcore_runtime_resume() as because of autosuspend
timeout we cannot enter idle between wlcore_irq_locked() and the end of
wlcore_irq().
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Guy Mishol <guym@ti.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 246 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.674189849@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bitmaps are defined on unsigned longs, so the usage of u32[2] in the
wlcore driver is incorrect. As noted by Peter Zijlstra, casting arrays
to a bitmap is incorrect for big-endian architectures.
When looking at it I observed that:
- operations on reg_ch_conf_pending is always under the wl_lock mutex,
so set_bit is overkill
- the only case where reg_ch_conf_pending is accessed a u32 at a time is
unnecessary too.
This patch cleans up everything in this area, and changes tmp_ch_bitmap
to have the proper alignment.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a goto statement that is missing a tab for indentation. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During "wlan-up", we are programming the FW into the WiFi-chip. However,
re-programming the FW doesn't work, unless a power cycle of the WiFi-chip
is made in-between the programmings.
To conform to this requirement and to fix the regression in a simple way,
let's start by allowing that the SDIO card (WiFi-chip) may stay powered on
(runtime resumed) when wl12xx_sdio_power_off() returns. The intent with the
current code is to treat this scenario as an error, but unfortunate this
doesn't work as expected, so let's fix this.
The other part is to guarantee that a power cycle of the SDIO card has been
completed when wl12xx_sdio_power_on() returns, as to allow the FW
programming to succeed. However, relying solely on runtime PM to deal with
this isn't sufficient. For example, userspace may prevent runtime suspend
via sysfs for the device that represents the SDIO card, leading to that the
mmc core also keeps it powered on. For this reason, let's instead do a
brute force power cycle in wl12xx_sdio_power_on().
Fixes: 728a9dc61f ("wlcore: sdio: Fix flakey SDIO runtime PM handling")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We return 0 unconditionally at the end of
'wlcore_vendor_cmd_smart_config_start()'.
However, 'ret' is set to some error codes in several error handling paths
and we already return some error codes at the beginning of the function.
Return 'ret' instead to propagate the error code.
Fixes: 80ff8063e8 ("wlcore: handle smart config vendor commands")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When receiving a beacon or probe response, we should update the
boottime_ns field which is the timestamp the frame was received at.
(cf mac80211.h)
This fixes a scanning issue with Android since it relies on this
timestamp to determine when the AP has been seen for the last time
(via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wl1271_warning() already appends a \n to the format,
so adding one to the warning string gives empty lines in the log.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case memory resources for *events_vector* were allocated, release
them before return.
Addresses-Coverity-ID: 1470194 ("Resource leak")
Fixes: 4ec7cece87 ("wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM tested working for wlcore with no autosuspend, we can
now enable autosuspend to cut down on enable/disable for interrupts.
Basically we just replace pm_runtime_put() with the autosuspend variants.
Let's use autosuspend delay of 50ms that MMC drivers typically use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have wl12xx_boot() call wl12xx_enable_interrupts() and if we have
wl1271_op_add_interface() call pm_runtime_get_sync() before the interrupts
are enabled. And then we get the following error during boot:
wlcore: ERROR ELP wakeup timeout!
Let's fix this by first checking if we need to boot the firmware. And
only after that call pm_runtime_get_sync() when interrupts are enabled.
And only after that do the check for wl12xx_need_fw_change().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we can now use calls to pm_runtime_force_suspend
and pm_runtime_force_resume for enabling elp during suspend when wowlan
is enabled and waking the chip from elp on resume.
Remove the custom API that was used to ensure that the command
that is used to allow ELP during suspend is completed before the system
suspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After enabling runtime PM, if we force hardware reset multiple times with:
# echo 1 > /sys/kernel/debug/ieee80211/phy0/wlcore/start_recovery
We will after few tries get the following error:
wlcore: ERROR timeout waiting for the hardware to complete initialization
And then wlcore is unable to reconnect until after the wlcore related modules
are reloaded.
Let's fix this by moving pm_runtime_put() earlier before we restart the hardware.
And let's use the sync version to make sure we're done before we restart.
Note that we still will get -EBUSY warning from wl12xx_sdio_set_power() but let's
fix that separately once we know exactly why we get the warning.
Reported-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we now need to have wlcore enabled longer
until after we're done calling wlcore_cmd_regdomain_config_locked():
scan_complete_work()
wlcore_cmd_regdomain_config_locked()
wlcore_cmd_send_failsafe()
wl12xx_sdio_raw_read()
Note that this is not needed before runtime PM support as the
custom PM code had it's own timer. We have not yet enabled runtime
PM autosuspend for wlcore and this is why this issue now shows up.
Let's fix the issues first before we enable runtime PM autosuspend.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can update wlcore to use PM runtime by adding functions for
wlcore_runtime_suspend() and wlcore_runtime_resume() and replacing
calls to wl1271_ps_elp_wakeup() and wl1271_ps_elp_sleep() with calls
to pm_runtime_get_sync() and pm_runtime_put().
Note that the new wlcore_runtime_suspend() and wlcore_runtime_resume()
functions are based on simplified versions of wl1271_ps_elp_sleep() and
wl1271_ps_elp_wakeup().
We don't want to use the old functions as we can now take advantage of
the runtime PM usage count. And we don't need the old elp_work at all.
And we can also remove WL1271_FLAG_ELP_REQUESTED that is no longer needed.
Pretty much the only place where we are not just converting the existing
functions is wl1271_op_suspend() where we add pm_runtime_put_noidle()
to keep the calls paired.
As the next step is to implement runtime PM autosuspend, let's not add
wrapper functions for the generic runtime PM calls. We would be getting
rid of any wrapper functions anyways.
After autoidle we should be able to start using Linux generic wakeirqs
for the padconf interrupt.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to wl1271_ps_elp_wakeup() in wl12xx_queue_recovery_work() is
unpaired. Let's remove it and add paired calls to wl1271_recovery_work()
instead in preparation for changing things to use runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Otherwise we can get:
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can have pm_runtime_get_sync() return 1, and we can have
pm_runtime_put_sync() return -EBUSY. See rpm_suspend() and
rpm_resume() for more information.
Fix the issue by returning 0 from wl12xx_sdio_power_on() on success.
And use pm_runtime_put() instead of pm_runtime_put_sync() for
wl12xx_sdio_power_off(), then the MMC subsystem will idle the bus
when suitable.
Otherwise wlcore can sometimes get confused and may report bogus
errors and WLAN connection can fail.
Note that while wlcore checks the return value for wl1271_power_on(),
the return value is ignored for wl1271_power_off(). Let's fix them
both though to avoid further confusion in the future.
Fixes: 60f36637bb ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.
In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.
Remove this manual power on/off sequence as it is in-fact not needed.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newly added wlcore_fw_sleep function is called conditionally,
which causes a warning without CONFIG_PM:
drivers/net/wireless/ti/wlcore/main.c:981:12: error: 'wlcore_fw_sleep' defined but not used [-Werror=unused-function]
Instead of trying to keep track of what should be in the #ifdef and what
should not, it's easier to mark the top-level suspend/resume functions
as __maybe_unused so the compiler can silently drop all the unused code.
Fixes: 37bf241b8e ("wlcore: allow elp during wowlan suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in error message text. Also remove the
error message on an kzalloc failure as this is redundant.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
when enabling wowlan and entering suspend the last write to the firmware
allowing it to go into elp mode was not completing before suspend, leaving
the firmware running in full active mode consuming high power.
Use an immediate call instead of a work queue for this last access
allowing the firmware to go into power save during wowlan uspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using getnstimeofday()/timespec_to_ns() causes an overflow on 32-bit
architectures in 2038, and may suffer from time jumps due to
settimeofday() or leap seconds.
I don't see a reason why this needs to be UTC, so either monotonic
or boot time would be better here. Assuming that the fw time keeps
running during suspend, boottime is better than monotonic, and
ktime_get_boot_ns() will also save the additional conversion to
nanoseconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
