In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same for this selftest.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks various aspects of VXLAN offloading and
the bridges do not need to participate in routing traffic. The IP addresses
or the RIFs are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks vetoing of a different aspect of the
configuration and the bridge does not need to participate in routing
traffic. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks DCB DSCP-based prioritization, and the
bridge serves for its L2 forwarding capabilities, and does not need to
participate in routing traffic. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks how many mirroring sessions a machine is
capable of offloading. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.
The selftest itself however checks whether a different vetoed aspect of the
configuration provides an extack. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are
not allowed to be created for 802.1ad bridges, but the address indicates
one needs to be created. Thus the veto selftests fail already during the
port enslavement. Then the attempt to create a VLAN on top of the same
bridge is not vetoed, because the bridge is not related to mlxsw, and the
selftest fails.
Fix by disabling automatic IPv6 address generation for the bridges in this
selftest, thus exempting them from the mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip link set dev "$devbond1" nomaster"
This line code in bond-eth-type-change.sh is unnecessary.
Because $devbond1 was not added to any master device.
Signed-off-by: Liang Li <liali@redhat.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to better polish building with BPF skels, so revert back to
making it an experimental feature that has to be explicitely enabled
using BUILD_BPF_SKEL=1.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCZFbCXwAKCRCyPKLppCJ+
J7cHAP97erKY4hBXArjpfzcvpFmboh/oqhbTLntyIpS6TEnOyQEAyervAPGIjQYC
DCo4foyXmOWn3dhNtK9M+YiRl3o2SgQ=
=7G78
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.
Build:
- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.
It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.
libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.
Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.
- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.
- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:
$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)
- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.
- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.
- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.
- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:
Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev
- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.
perf BPF filters:
- New feature where BPF can be used to filter samples, for instance:
$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)
- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:
Essentially the BPF filter expression is:
<term> <operator> <value> (("," | "||") <term> <operator> <value>)*
The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops
The <operator> can be one of:
==, !=, >, >=, <, <=, &
The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)
perf lock contention:
- Show lock type with address.
- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:
$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80
- Update default map size to 16384.
- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.
- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).
- Fix problems found with MSAn.
perf report/top:
- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.
- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.
perf sched:
- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d4 ("perf sched: Prefer sched_waking event when it
exists").
perf ftrace:
- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:
# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#
perf top:
- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.
- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.
perf annotate:
- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.
perf kvm:
- Add TUI mode for 'perf kvm stat report'.
Reference counting:
- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.
To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:
https://perf.wiki.kernel.org/index.php/Reference_Count_Checking
- The above caught, for instance, fix, present in this series:
- Fix maps use after put in 'perf test "Share thread maps"':
'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.
Fixed by reversing the order of puts so that the leader is put
last.
- Also several fixes were made to places where reference counts were
not being held.
- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.
ARM64:
- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.
- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".
arm64 vendor events:
- Add N1 metrics.
Intel vendor events:
- Add graniterapids, grandridge and sierraforrest events.
- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp
- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.
perf stat:
- Implement --topdown using JSON metrics.
- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.
- Use metrics for --smi-cost.
- Update topdown documentation.
Vendor events (JSON) infrastructure:
- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:
{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},
- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.
- Support for printing metric thresholds in 'perf list'.
- Add --metric-no-threshold option to 'perf stat'.
- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.
- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.
S/390:
- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).
- Add cache metrics for z13, z14, z15 and z16.
- Add metric for TLB and cache.
ARM:
- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.
Intel PT hardware tracing:
- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.
- Add support for new branch instructions ERETS and ERETU.
- Fix CYC timestamps after standalone CBR
ARM CoreSight hardware tracing:
- Allow user to override timestamp and contextid settings.
- Fix segfault in dso lookup.
- Fix timeless decode mode detection.
- Add separate decode paths for timeless and per-thread modes.
auxtrace:
- Fix address filter entire kernel size.
Miscellaneous:
- Fix use-after-free and unaligned bugs in the PLT handling routines.
- Use zfree() to reduce chances of use after free.
- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.
- Suppress massive unsupported target platform errors in the unwind
code.
- Fix return incorrect build_id size in elf_read_build_id().
- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .
- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.
- Add 'perf bench syscall fork' benchmark.
- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.
- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.
- Fix some spelling mistakes"
* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...
mlxsw selftests often invoke a bail_on_lldpad() helper to make sure LLDPAD
is not running, to prevent conflicts between the QoS configuration applied
through TC or DCB command line tool, and the DCB configuration that LLDPAD
might apply. This helper might be useful to others. Move the function to
lib.sh, and parameterize to make reusable in other contexts.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver-specific wrappers of these selftests invoke bail_on_lldpad to
make sure that LLDPAD doesn't trample the configuration. The function
bail_on_lldpad is going to move to lib.sh in the next patch. With that, it
won't be visible for the wrappers before sourcing the framework script. And
after sourcing it, it is too late: the selftest will have run by then.
One option might be to source NUM_NETIFS=0 lib.sh from the wrapper, but
even if that worked (it might, it might not), that seems cumbersome. lib.sh
is doing fair amount of stuff, and even if it works today, it does not look
particularly solid as a solution.
Instead, introduce a hook, sch_tbf_pre_hook(), that when available, gets
invoked. Move the bail to the hook.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add bonding arp validate tests with mode active backup,
monitor arp_ip_target and ns_ip6_target. It also checks mii_status
to make sure all slaves are UP.
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve the testing process for bond options, A new bond topology lib
is added to our testing setup. The current option_prio.sh file will be
renamed to bond_options.sh so that all bonding options can be tested here.
Specifically, for priority testing, we will run all tests using modes
1, 5, and 6. These changes will help us streamline the testing process
and ensure that our bond options are rigorously evaluated.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new network selftests for the bonding device which exercise the ether
type changing call paths. They also test for the recent syzbot bug[1] which
causes a warning and results in wrong device flags (IFF_SLAVE missing).
The test adds three bond devices and a nlmon device, enslaves one of the
bond devices to the other and then uses the nlmon device for successful
and unsuccesful enslaves both of which change the bond ether type. Thus
we can test for both MASTER and SLAVE flags at the same time.
If the flags are properly restored we get:
TEST: Change ether type of an enslaved bond device with unsuccessful enslave [ OK ]
TEST: Change ether type of an enslaved bond device with successful enslave [ OK ]
[1] https://syzkaller.appspot.com/bug?id=391c7b1f6522182899efba27d891f1743e8eb3ef
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com>
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use $(KHDR_INCLUDES) as lookup path for kernel headers. This prevents
building against kernel headers from the build environment in scenarios
where kernel headers are installed into a specific output directory
(O=...).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-kselftest@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org> # 5.18+
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
We have two IS1 filters of the OCELOT_VCAP_KEY_ANY key type (the one with
"action vlan pop" and the one with "action vlan modify") and one of the
OCELOT_VCAP_KEY_IPV4 key type (the one with "action skbedit priority").
But we have no IS1 filter with the OCELOT_VCAP_KEY_ETYPE key type, and
there was an uncaught breakage there.
To increase test coverage, convert one of the OCELOT_VCAP_KEY_ANY
filters to OCELOT_VCAP_KEY_ETYPE, by making the filter also match on the
MAC SA of the traffic sent by mausezahn, $h1_mac.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-2-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Set up default port priority through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set up DSCP prioritization through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set up DSCP prioritization through the iproute2 dcb tool, which is easier
to understand and manage.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NetworkManager (and other daemons) may bring the interface up
and cause failures in quiescence checks. Print a helpful warning,
and take the interface down again.
I seem to forget about this every time I run these tests on a new VM.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
$number + > bash means redirect FD $number, e.g. commonly
used 2> redirects stderr (fd 2). The test uses 8192> to
write the number 8192 to a file, this results in:
./devlink.sh: line 499: 8192: Bad file descriptor
Oddly the test also papers over this issue by checking
for failure (expecting an error rather than success)
so it passes, anyway.
Fixes: ff18176ad8 ("selftests: Add a test of large binary to devlink health test")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test for bonding prio option. Here is the test result:
]# ./option_prio.sh
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=0) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=1) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=arp_ip_target and primary_reselect=2) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=0) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=1) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=1 monitor=miimon and primary_reselect=2) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=0) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=1) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=5 monitor=miimon and primary_reselect=2) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=0) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=1) [ OK ]
TEST: prio_test (Test bonding option 'prio' with mode=6 monitor=miimon and primary_reselect=2) [ OK ]
Signed-off-by: Liang Li <liali@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that Spectrum-1 gained ip6gre support we can move the test out of
the Spectrum-2 directory.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Verify when a bond is configured with {up,down}delay and the link state
of slave members flaps if there are no remaining members up the bond
should immediately select a member to bring up. (from bonding.txt
section 13.1 paragraph 4)
Suggested-by: Liang Li <liali@redhat.com>
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that locked bridge port configurations that are not supported by
mlxsw are rejected.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that packets received via a locked bridge port whose {SMAC, VID}
does not appear in the bridge's FDB or appears with a different port,
trigger the "locked_port" packet trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that packets with a destination MAC of 01:80:C2:00:00:03 trigger
the "eapol" packet trap.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
lag_lib.sh creates the interfaces dummy1 and dummy2 whereas
dev_addr_lists.sh:destroy() deletes the interfaces dummy0 and dummy1. Fix
the mismatch in names.
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When exporting and running a subset of selftests via kselftest, files from
parts of the source tree which were not exported are not available. A few
tests are trying to source such files. Address the problem by using
symlinks.
The problem can be reproduced by running:
make -C tools/testing/selftests gen_tar TARGETS="drivers/net/bonding"
[... extract archive ...]
./run_kselftest.sh
or:
make kselftest KBUILD_OUTPUT=/tmp/kselftests TARGETS="drivers/net/bonding"
Fixes: bbb774d921 ("net: Add tests for bonding and team address list management")
Fixes: eccd0a80dc ("selftests: net: dsa: add a stress test for unlocked FDB operations")
Link: https://lore.kernel.org/netdev/40f04ded-0c86-8669-24b1-9a313ca21076@redhat.com/
Reported-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can make the phc2sys helper not only synchronize a PHC to
CLOCK_REALTIME, which is what it currently does, but also CLOCK_REALTIME
to a PHC, which is going to be needed in distributed TSN tests.
Instead of making the complexity of the arguments passed to
phc2sys_start() explode, we can let it figure out the sync direction
automatically, based on ptp4l's port states.
Towards that goal, pass just the path to the desired ptp4l instance's
UNIX domain socket, and remove the $if_name argument (from which it
derives the PHC). Also adapt the one caller from the ocelot psfp.sh
test. In the case of psfp.sh, phc2sys_start is able to properly figure
out that CLOCK_REALTIME is the source clock and swp1's PHC is the
destination, because of the way in which ptp4l_start for the
UDS_ADDRESS_SWP1 was called: with slave_only=false, so it will always
win the BMCA and always become the sync master between itself and $h1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It looks like this test has been accidentally dropped when resolving
conflicts in this Makefile.
Most probably because there were 3 different patches modifying this file
in parallel:
commit 152e8ec776 ("selftests/bonding: add a test for bonding lladdr target")
commit bbb774d921 ("net: Add tests for bonding and team address list management")
commit 2ffd57327f ("selftests: bonding: cause oops in bond_rr_gen_slave_id")
The first one was applied in 'net-next' while the two other ones were
recently applied in the 'net' tree.
But that's alright, easy to fix by re-adding the missing one!
Fixes: 0140a7168f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/20220923082306.2468081-1-matthieu.baerts@tessares.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bonding selftest used to cause a kernel oops on aarch64
and should be architectures agnostic.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a regression test for commit 592335a416 ("bonding: accept
unsolicited NA message") and commit b7f14132bf ("bonding: use unspecified
address if no available link local address"). When the bond interface
up and no available link local address, unspecified address(::) is used to
send the NS message. The unsolicited NA message should also be accepted
for validation.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220920033047.173244-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch added a test which can be used instead of qos_burst.sh.
Remove this test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an equivalent test to qos_burst, the test's purpose is same, but the
new test uses simpler topology and does not require forcing low speed.
In addition, it can be run Spectrum-2 and not only Spectrum-3+. The idea
is to use a shaper in order to limit the traffic and create congestion.
qos_burst test uses small pool, sends many small packets, and verify that
packets are not dropped, which means that many descriptors can be handled.
This test should check the change that commit c864769add
("mlxsw: Configure descriptor buffers") pushed.
Instead, the new test tries to use more than 85% of maximum supported
descriptors. The idea is to use big pool (as much as the ASIC supports),
such that the pool size does not limit the traffic, then send many small
packets, which means that many descriptors are used, and check how many
packets the switch can handle.
The usage of shaper allows to run the test in all ASICs, regardless of
the CPU abilities, as it is able to create the congestion with low rate
of packets.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run the tests there, some adjustments are required. Use shapers to limit
the traffic instead of forcing speed. Note that for several ports, the
speed configuration is just for autoneg issues, so shaper is not needed
instead.
The tests already use ETS qdisc as a root and RED qdiscs as children. Add
a new TBF shaper to limit the rate of traffic, and use it as a root qdisc,
then save the previous hierarchy of qdiscs under the new TBF root.
In some ASICs, the shapers do not limit the traffic as accurately as
forcing speed. To make the tests stable, allow the backlog size to be up to
+-10% of the threshold. The aim of the tests is to make sure that with
backlog << threshold, there are no drops, and that packets are dropped
somewhere in vicinity of the configured threshold.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
QOS tests create congestion and verify the switch behavior. To create
congestion, they need to have more traffic than the port can handle, so
some of them force 1Gbps speed.
The tests assume that 1Gbps speed is supported, otherwise, they will fail.
Spectrum-4 ASIC will not support this speed in all ports, so to be able
to run QOS tests there, some adjustments are required. Use shapers to
limit the traffic instead of forcing speed. Note that for several ports,
the speed configuration is just for autoneg issues, so shaper is not needed
instead.
In tests that already use shapers, set the existing shaper to be a child of
a new TBF shaper which is added as a root qdisc and acts as a port shaper.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata
Jakub Kicinski
Linus Torvalds
Liang Li
Hangbin Liu
Patrice Duroux
Nikolay Aleksandrov
Jiri Pirko
Mathieu Desnoyers
Vladimir Oltean
Ido Schimmel
Jonathan Toppins
Benjamin Poirier
Matthieu Baerts
Amit Cohen