arm64: dts: qcom: msm8939-longcheer-l9100: Add initial device tree
This dts adds support for BQ Aquaris M5 (Longcheer L9100) released in 2015. Add a device tree with initial support for: - GPIO keys - Hall sensor - SDHCI - WCNSS (BT/WIFI) - Accelerometer/Magnetometer - Vibrator - Touchscreen - Front flash Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: André Apitzsch <git@apitzsch.eu> Link: https://lore.kernel.org/r/20230827-bq_m5-v4-2-f8435fb8f955@apitzsch.eu Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This commit is contained in:
André Apitzsch
committed by
Bjorn Andersson
Bjorn Andersson
parent
9905205541
commit
27da4fd325
@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8916-yiming-uz801v3.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8939-longcheer-l9100.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8939-samsung-a7.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti-tulip.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
|
||||
|
||||
334
arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts
Normal file
334
arch/arm64/boot/dts/qcom/msm8939-longcheer-l9100.dts
Normal file
@@ -0,0 +1,334 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "msm8939-pm8916.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
|
||||
|
||||
/ {
|
||||
model = "BQ Aquaris M5 (Longcheer L9100)";
|
||||
compatible = "longcheer,l9100", "qcom,msm8939";
|
||||
chassis-type = "handset";
|
||||
|
||||
aliases {
|
||||
mmc0 = &sdhc_1; /* eMMC */
|
||||
mmc1 = &sdhc_2; /* SD card */
|
||||
serial0 = &blsp_uart2;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0";
|
||||
};
|
||||
|
||||
gpio-hall-sensor {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
pinctrl-0 = <&gpio_hall_sensor_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
label = "GPIO Hall Effect Sensor";
|
||||
|
||||
event-hall-sensor {
|
||||
label = "Hall Effect Sensor";
|
||||
gpios = <&tlmm 20 GPIO_ACTIVE_LOW>;
|
||||
linux,input-type = <EV_SW>;
|
||||
linux,code = <SW_LID>;
|
||||
linux,can-disable;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
pinctrl-0 = <&gpio_keys_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
label = "GPIO Buttons";
|
||||
|
||||
button-volume-up {
|
||||
label = "Volume Up";
|
||||
gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
default-state = "off";
|
||||
function = LED_FUNCTION_KBD_BACKLIGHT;
|
||||
|
||||
pinctrl-0 = <&button_backlight_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
};
|
||||
|
||||
reg_ts_vdd: regulator-vdd-ts {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "regulator-vdd-ts";
|
||||
regulator-min-microvolt = <2850000>;
|
||||
regulator-max-microvolt = <2850000>;
|
||||
|
||||
gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
|
||||
pinctrl-0 = <&ts_vdd_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pm8916_pwm 0 100000>;
|
||||
brightness-levels = <0 255>;
|
||||
num-interpolated-steps = <255>;
|
||||
default-brightness-level = <128>;
|
||||
enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
pinctrl-0 = <&lcd_bl_en_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
flash-led-controller {
|
||||
compatible = "ocs,ocp8110";
|
||||
flash-gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
|
||||
enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
pinctrl-0 = <&camera_front_flash_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led {
|
||||
function = LED_FUNCTION_FLASH;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
flash-max-timeout-us = <250000>;
|
||||
};
|
||||
};
|
||||
|
||||
usb_id: usb-id {
|
||||
compatible = "linux,extcon-usb-gpio";
|
||||
id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&usb_id_default &usb_id_switch_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&blsp_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
magnetometer@d {
|
||||
compatible = "asahi-kasei,ak09911";
|
||||
reg = <0x0d>;
|
||||
|
||||
vdd-supply = <&pm8916_l17>;
|
||||
vid-supply = <&pm8916_l6>;
|
||||
|
||||
reset-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
pinctrl-0 = <&mag_reset_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
light-sensor@23 {
|
||||
compatible = "liteon,ltr559";
|
||||
reg = <0x23>;
|
||||
|
||||
vdd-supply = <&pm8916_l17>;
|
||||
vddio-supply = <&pm8916_l5>;
|
||||
|
||||
interrupts-extended = <&tlmm 113 IRQ_TYPE_EDGE_FALLING>;
|
||||
|
||||
pinctrl-0 = <&light_int_default>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
imu@68 {
|
||||
compatible = "bosch,bmi160";
|
||||
reg = <0x68>;
|
||||
|
||||
vdd-supply = <&pm8916_l17>;
|
||||
vddio-supply = <&pm8916_l6>;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_i2c5 {
|
||||
status = "okay";
|
||||
|
||||
touchscreen@4a {
|
||||
compatible = "atmel,maxtouch";
|
||||
reg = <0x4a>;
|
||||
|
||||
interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
vdda-supply = <&pm8916_l6>;
|
||||
vdd-supply = <®_ts_vdd>;
|
||||
|
||||
pinctrl-0 = <&ts_int_reset_default>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
/* Keys listed from right to left */
|
||||
linux,keycodes = <KEY_APPSELECT KEY_HOMEPAGE KEY_BACK>;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_uart2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8916_mpps {
|
||||
pwm_out: mpp4-state {
|
||||
pins = "mpp4";
|
||||
function = "digital";
|
||||
power-source = <PM8916_MPP_VPH>;
|
||||
output-low;
|
||||
qcom,dtest = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&pm8916_pwm {
|
||||
pinctrl-0 = <&pwm_out>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8916_resin {
|
||||
linux,code = <KEY_VOLUMEDOWN>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pm8916_rpm_regulators {
|
||||
pm8916_l17: l17 {
|
||||
regulator-min-microvolt = <2850000>;
|
||||
regulator-max-microvolt = <2850000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pm8916_vib {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdhc_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdhc_2 {
|
||||
pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
|
||||
pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
|
||||
cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb {
|
||||
extcon = <&usb_id>, <&usb_id>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_hs_phy {
|
||||
extcon = <&usb_id>;
|
||||
};
|
||||
|
||||
&wcnss {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wcnss_iris {
|
||||
compatible = "qcom,wcn3620";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
button_backlight_default: button-backlight-default-state {
|
||||
pins = "gpio17";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
camera_front_flash_default: camera-front-flash-default-state {
|
||||
pins = "gpio8", "gpio49";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
gpio_hall_sensor_default: gpio-hall-sensor-default-state {
|
||||
pins = "gpio20";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
gpio_keys_default: gpio-keys-default-state {
|
||||
pins = "gpio107";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
lcd_bl_en_default: lcd-bl-en-default-state {
|
||||
pins = "gpio98";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
light_int_default: light-int-default-state {
|
||||
pins = "gpio113";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
mag_reset_default: mag-reset-default-state {
|
||||
pins = "gpio68";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
sdc2_cd_default: sdc2-cd-default-state {
|
||||
pins = "gpio38";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
ts_int_reset_default: ts-int-reset-default-state {
|
||||
pins = "gpio12", "gpio13";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
ts_vdd_default: ts-vdd-default-state {
|
||||
pins = "gpio78";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
usb_id_default: usb-id-default-state {
|
||||
pins = "gpio110";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
usb_id_switch_default: usb-id-switch-default-state {
|
||||
pins = "gpio121";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
Reference in New Issue
Block a user