To prevent the driver from doing recursive command buffer
resets, just panic when that recursion happens.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
On an ILLEGAL_COMMAND_ERROR the IOMMU stops executing
further commands. This patch changes the code to handle this
case better by resetting the command buffer in the IOMMU.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch factors parts of the command buffer
initialization code into a seperate function which can be
used to reset the command buffer later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This function flushes all DTE entries on one IOMMU for all
devices behind this IOMMU. This is required for command
buffer resetting later.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The amd_iommu_pd_table is indexed by protection domain
number and not by device id. So this check is broken and
must be removed.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch replaces the "AMD IOMMU" printk strings with the
official name for the hardware: "AMD-Vi".
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch removes some left-overs which where put into the code to
simplify merging code which also depends on changes in other trees.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch introduces a function to flush all domain tlbs
for on one given IOMMU. This is required later to reset the
command buffer on one IOMMU.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds code to dump the command which caused an
ILLEGAL_COMMAND_ERROR raised by the IOMMU hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds code to dump the content of the device table
entry which caused an ILLEGAL_DEV_TABLE_ENTRY error from the
IOMMU hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This is a compromise and a temporary workaround for bootup NMI
watchdog triggers some people see with qla2xxx devices present.
This happens when, for example:
CPU 0 is in the driver init and looping submitting mailbox commands to
load the firmware, then waiting for completion.
CPU 1 is receiving the device interrupts. CPU 1 is where the NMI
watchdog triggers.
CPU 0 is submitting mailbox commands fast enough that by the time CPU
1 returns from the device interrupt handler, a new one is pending.
This sequence runs for more than 5 seconds.
The problematic case is CPU 1's timer interrupt running when the
barrage of device interrupts begin. Then we have:
timer interrupt
return for softirq checking
pending, thus enable interrupts
qla2xxx interrupt
return
qla2xxx interrupt
return
... 5+ seconds pass
final qla2xxx interrupt for fw load
return
run timer softirq
return
At some point in the multi-second qla2xxx interrupt storm we trigger
the NMI watchdog on CPU 1 from the NMI interrupt handler.
The timer softirq, once we get back to running it, is smart enough to
run the timer work enough times to make up for the missed timer
interrupts.
However, the NMI watchdogs (both x86 and sparc) use the timer
interrupt count to notice the cpu is wedged. But in the above
scenerio we'll receive only one such timer interrupt even if we last
all the way back to running the timer softirq.
The default watchdog trigger point is only 5 seconds, which is pretty
low (the softwatchdog triggers at 60 seconds). So increase it to 30
seconds for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes up the kmap_coherent/kunmap_coherent() interface for recent
changes both in the page fault path and the shared cache flushers, as
well as adding in some optimizations.
One of the key things to note here is that the TLB flush itself is
deferred until the unmap, and the call in to update_mmu_cache() itself
goes away, relying on the regular page fault path to handle the lazy
dcache writeback if necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Target state can be read / programmed via files under:
[debugfs]/pm_debug/[pwrdm]/suspend
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Allows dumping out current register contents from the debug filesystem, and
also allows user to add arbitrary register save points into code. Current
register contents are available under debugfs at:
[debugfs]/pm_debug/registers/current
To add a save point, do following:
From module init (or somewhere before the save call, called only once):
pm_dbg_init_regset(n); // n=1..4, allocates memory for dump area #n
From arbitrary code location:
pm_dbg_regset_save(n); // n=1..4, saves registers to dump area #n
After this, the register dump can be seen under [debugfs]/pm_debug/registers/n
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make the powerdomain code call the new hook for updating the time.
Also implement the updated pwrdm_for_each.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides the debugfs entries and a function which will be
called by the PM code to register the time spent per domain per
state. Also some new fields are added to the powerdomain struct to
keep the time information.
NOTE: As of v2.6.29, using getnstimeofday() after drivers are
suspended is no longer safe since the timekeeping subsystem is also
suspended as part of the suspend process. Instead use sched_clock()
which on OMAP returns the 32k SYNC timer in nanoseconds.
Also, do not print out status for meta powerdomains (dpll*)
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the clock, clockdomain and OMAP3 specific
powerdomain code to call the PM counter infrastructure whenever one or
more powerdomains might have changed state.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides the infrastructure to count how many times a
powerdomain entered a given power state (on, inactive, retention,
off). A number of functions are provided which will be called by the
chip specific powerdomain and clockdomain code whenever a transition
might have happened.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch uses kmalloc(size,GFP_ATOMIC) instead of kmalloc(size,GFP_KERNEL)
to allocate memory for instance of struct power_state in pwrdms_setup(),
since it may be called by pwrdm_for_each() with irq disabled.
It is a easy fix for the following lockdep warning caused by
kmalloc(size,GFP_KERNEL) in pwrdms_setup():
Power Management for TI OMAP3.
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2282 lockdep_trace_alloc+0xe8/0xfc()
Modules linked in:
[<c0032ccc>] (unwind_backtrace+0x0/0xec) from [<c0056934>] (warn_slowpath_common+0x48/0x60)
[<c0056934>] (warn_slowpath_common+0x48/0x60) from [<c007da10>] (lockdep_trace_alloc+0xe8/0xfc)
[<c007da10>] (lockdep_trace_alloc+0xe8/0xfc) from [<c00cd9bc>] (kmem_cache_alloc+0x28/0x178)
[<c00cd9bc>] (kmem_cache_alloc+0x28/0x178) from [<c000f184>] (pwrdms_setup+0x30/0xf8)
[<c000f184>] (pwrdms_setup+0x30/0xf8) from [<c00381c4>] (pwrdm_for_each+0x64/0x84)
[<c00381c4>] (pwrdm_for_each+0x64/0x84) from [<c000ef60>] (omap3_pm_init+0x3f4/0x5ac)
[<c000ef60>] (omap3_pm_init+0x3f4/0x5ac) from [<c002c2c0>] (do_one_initcall+0x30/0x1d4)
[<c002c2c0>] (do_one_initcall+0x30/0x1d4) from [<c00088d8>] (kernel_init+0xa4/0x118)
[<c00088d8>] (kernel_init+0xa4/0x118) from [<c002ddf8>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1e06f8d97dc5a19b ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch changes for setting the padconf value for sys_nirq line
which is connected to T2 INTR1. This will fix the T2 keypad wakeup
issue on OMAP3 SDP.
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In usb_musb_pm_init, we attempt to access an MUSB register
when the i-clock may not be on, or the module is otherwise
not accessible.
We need to either:
- enable the clock before this access, or
- remove this code and move it to the bootloader, or
- enable the clock in the bootloader
If we enable the clock in the bootloader, we might as well
add the workaround in the bootloader itself. This code will
anyway be changed once hwmod is in place, so remove it for now
This allows us to boot the kernel on certain OMAP3 boards with
a bootloader that doesn't enable this clock. Without this, we
will need to upgrade the bootloaders on these boards.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Now that on-chip UARTs each have separate platform_data, the external
UART needs an non-conflicting ID. Since there are 3 on-chip UARTs,
the Zoom2 external UART will be registered after as the fourth.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Second reason of OMAP4 boot failure on 2.6.31.rc6, the UART
platform data is not getting registered to kernel.
Registration was failing because of clock check failure in
omap_serial_init().
Below patch fix the same.
OMAP4 clock framework patches are still getting discussed on mailing
list so till then we need this.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
After the patch series "[PATCH 00/14] OMAP PM fixes for .31-rc"
merge in 2.6.31-rc5, the kernel crashed during boot on OMAP4430.
This patch fixes it by adding UART4 support and related code.
Without this patch omap_serial_init() would produce " NULL pointer
dereference" and kernel crashes in the bootup on OMAP4430 platform.
Some more info on the merge issue can be found here.
More info- http://lkml.org/lkml/2009/8/20/192
Note: While merging this patch,"IO_ADDRESS" needs to be changed
to "OMAP2_IO_ADDRESS" if the Tony's below series is already merged in.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15072.html
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The 32-bit parameters (len and csum) of csum_ipv6_magic() are passed in 64-bit
registers in2 and in4. The high order 32 bits of the registers were never
cleared, and garbage was sometimes calculated into the checksum.
Fix this by clearing the high order 32 bits of these registers.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/dma-mapping.c:14: warning: control reaches end of non-void function
arch/ia64/kernel/dma-mapping.c:14: warning: no return statement in function returning non-void
This warning was introduced by commit: 390bd132b2
Add dma_debug_init() for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a keyctl to install a process's session keyring onto its parent. This
replaces the parent's session keyring. Because the COW credential code does
not permit one process to change another process's credentials directly, the
change is deferred until userspace next starts executing again. Normally this
will be after a wait*() syscall.
To support this, three new security hooks have been provided:
cred_alloc_blank() to allocate unset security creds, cred_transfer() to fill in
the blank security creds and key_session_to_parent() - which asks the LSM if
the process may replace its parent's session keyring.
The replacement may only happen if the process has the same ownership details
as its parent, and the process has LINK permission on the session keyring, and
the session keyring is owned by the process, and the LSM permits it.
Note that this requires alteration to each architecture's notify_resume path.
This has been done for all arches barring blackfin, m68k* and xtensa, all of
which need assembly alteration to support TIF_NOTIFY_RESUME. This allows the
replacement to be performed at the point the parent process resumes userspace
execution.
This allows the userspace AFS pioctl emulation to fully emulate newpag() and
the VIOCSETTOK and VIOCSETTOK2 pioctls, all of which require the ability to
alter the parent process's PAG membership. However, since kAFS doesn't use
PAGs per se, but rather dumps the keys into the session keyring, the session
keyring of the parent must be replaced if, for example, VIOCSETTOK is passed
the newpag flag.
This can be tested with the following program:
#include <stdio.h>
#include <stdlib.h>
#include <keyutils.h>
#define KEYCTL_SESSION_TO_PARENT 18
#define OSERROR(X, S) do { if ((long)(X) == -1) { perror(S); exit(1); } } while(0)
int main(int argc, char **argv)
{
key_serial_t keyring, key;
long ret;
keyring = keyctl_join_session_keyring(argv[1]);
OSERROR(keyring, "keyctl_join_session_keyring");
key = add_key("user", "a", "b", 1, keyring);
OSERROR(key, "add_key");
ret = keyctl(KEYCTL_SESSION_TO_PARENT);
OSERROR(ret, "KEYCTL_SESSION_TO_PARENT");
return 0;
}
Compiled and linked with -lkeyutils, you should see something like:
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
355907932 --alswrv 4043 -1 \_ keyring: _uid.4043
[dhowells@andromeda ~]$ /tmp/newpag
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
1055658746 --alswrv 4043 4043 \_ user: a
[dhowells@andromeda ~]$ /tmp/newpag hello
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: hello
340417692 --alswrv 4043 4043 \_ user: a
Where the test program creates a new session keyring, sticks a user key named
'a' into it and then installs it on its parent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Implement TIF_NOTIFY_RESUME for most of those architectures in which isn't yet
available, and, whilst we're at it, have it call the appropriate tracehook.
After this patch, blackfin, m68k* and xtensa still lack support and need
alteration of assembly code to make it work.
Resume notification can then be used (by a later patch) to install a new
session keyring on the parent of a process.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
cc: linux-arch@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
In xdr_partial_copy_from_skb() there is that sequence:
kaddr = kmap_atomic(*ppage, KM_SKB_SUNRPC_DATA);
[...]
flush_dcache_page(*ppage);
kunmap_atomic(kaddr, KM_SKB_SUNRPC_DATA);
Mixing flush_dcache_page() and kmap_atomic() is a bit odd,
especially since kunmap_atomic() must deal with cache issues
already. OTOH the non-highmem case must use flush_dcache_page()
as kunmap_atomic() becomes a no op with no cache maintenance.
Problem is that with highmem the implementation of kmap_atomic()
doesn't set page->virtual, and page_address(page) returns 0 in
that case. Here flush_dcache_page() calls __flush_dcache_page()
which calls __cpuc_flush_dcache_page(page_address(page)) resulting
in a kernel oops.
None of the kmap_atomic() implementations uses set_page_address().
Hence we can assume page_address() is always expected to return 0 in
that case. Let's conditionally call __cpuc_flush_dcache_page() only
when the page address is non zero, and perform that test only when
highmem is configured.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the cpu.c and dev.c and modify w90p910 platform
to apply to use the common API(provided by cpu.c and dev.c)
at the same time, I renamed all w90x900 to nuc900 in every
c file of w90x900 platform and touchscreen's driver name.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A misconfiguration by the firmware of the U4 PCIe bridge on PowerMac G5
with the U4 bridge (latest generations, may also affect the iMac G5
"iSight") is causing us to re-assign the PCI BARs of the video card,
which can get it out of sync with the firmware, thus breaking offb.
This works around it by fixing up the bridge configuration properly
at boot time. It also fixes a bug where the firmware provides us with
an incorrect set of accessible regions in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Switch to using the Power ISA defined PTE format when we have a 64-bit
PTE. This makes the code handling between fsl-booke and book3e-64
similiar for TLB faults.
Additionally this lets use take advantage of the page size encodings and
full permissions that the HW PTE defines.
Also defined _PMD_PRESENT, _PMD_PRESENT_MASK, and _PMD_BAD since the
32-bit ppc arch code expects them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add defines for the other page sizes. Even if HW doesn't support them
we made them use them for hugetlbfs support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The SLB can change sizes across a live migration, which was not
being handled, resulting in possible machine crashes during
migration if migrating to a machine which has a smaller max SLB
size than the source machine. Fix this by first reducing the
SLB size to the minimum possible value, which is 32, prior to
migration. Then during the device tree update which occurs after
migration, we make the call to ensure the SLB gets updated. Also
add the slb_size to the lparcfg output so that the migration
tools can check to make sure the kernel has this capability
before allowing migration in scenarios where the SLB size will change.
BenH: Fixed #include <asm/mmu-hash64.h> -> <asm/mmu.h> to avoid
breaking ppc32 build
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
arch/x86/kernel/reboot.c
security/Kconfig
Merge reason: resolve the conflicts, bump up from rc3 to rc8.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The two versions are doing almost exactly the same thing. No need to
maintain them as separate files. This patch also has the side effect
of making the PCI device tree scanning code available to 32 bit powerpc
machines, but no board ports actually make use of this feature at this
point.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This function measures whether the FPU/SSE state can be touched in
interrupt context. If the interrupted code is in user space or has no
valid FPU/SSE context (CR0.TS == 1), FPU/SSE state can be used in IRQ
or soft_irq context too.
This is used by AES-NI accelerated AES implementation and PCLMULQDQ
accelerated GHASH implementation.
v3:
- Renamed to irq_fpu_usable to reflect the purpose of the function.
v2:
- Renamed to irq_is_fpu_using to reflect the real situation.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Move tboot.h from asm to linux to fix the build errors of intel_txt
patch on non-X86 platforms. Remove the tboot code from generic code
init/main.c and kernel/cpu.c.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
msr-reg.S used the :req option on a macro argument, which wasn't
supported by gas 2.16.1 (but apparently by some earlier versions of
gas, just to be confusing.) It isn't necessary, so just remove it.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
