Create a blacklist for processors that should not load the acpi-cpufreq module.
The initial entry in the blacklist function is the Intel 0f68 processor. It's
specification update mentions errata AL30 which implies that cpufreq should not
run on this processor.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove an obsolete check that used to prevent there being more
than 2 low P-states. Now that low-to-low P-states changes are
enabled, it prevents otherwise workable configurations with
multiple low P-states.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Krists Krilovs <pow@pow.za.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Convert CRIS to use asm-generic/hardirq.h
Also remove unneeded (incorrect) prototypes for setup_irq().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
This board doesn't use trapped I/O for anything, so just kill off the
select. This was causing problems in the unhandled page fault die path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This builds on top of the previous reversion and implements a special
on_each_cpu() variant that simple disables preemption across the call
while leaving the interrupt state to the function itself. There were some
unintended consequences with IRQ disabling in some of these paths on UP
that ran in to a deadlock scenario with IRQs being missed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 64a6d72213.
Unfortunately we can't use on_each_cpu() for all of the cache ops, as
some of them only require preempt disabling. This seems to be the same
issue that impacts the mips r4k caches, where this code was based on.
This fixes up a deadlock that showed up in some IRQ context cases.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This block is allocated with alloc_bootmem() and scanned by kmemleak but
the kernel direct mapping may no longer exist. This patch tells kmemleak
to ignore this memory hole. The dma32_bootmem_ptr in
dma32_reserve_bootmem() is also ignored.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
The kgdb stub has traditionally tied in to the NMI slot, and manually
handled debounce. Now that we have a generic way to do this instead, all
of the stub-specific debounce silliness can be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for NMI debugging that was shamelessly copied
from the avr32 port. A bit of special magic is needed in the interrupt
exception path given that the NMI exception handler is stubbed in to the
regular exception handling table despite being reported in INTEVT. So we
mangle the lookup and kick off an EXPEVT-style exception dispatch from
the INTEVT path for exceptions that do_IRQ() has no chance of handling.
As a result, we also drop the evt2irq() conversion from the do_IRQ() path
and just do it in assembly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adopts the special-cased 2-way write-through dcache flusher for
N-ways and moves it in to the generic path. Assignment is done at runtime
via the check for the CCR_CACHE_WT bit in the same path as the per-way
writeback flushers.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make it possible to access the all-register-setting/getting MSR
functions via the MSR driver. This is implemented as an ioctl() on
the standard MSR device node.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <petkovbb@gmail.com>
Create _on_cpu helpers for {rw,wr}msr_safe_regs() analogously with the
other MSR functions. This will be necessary to add support for these
to the MSR driver.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <petkovbb@gmail.com>
For some reason, the _safe MSR functions returned -EFAULT, not -EIO.
However, the only user which cares about the return code as anything
other than a boolean is the MSR driver, which wants -EIO. Change it
to -EIO across the board.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Add CFI annotations for native_{rd,wr}msr_safe_regs().
Simplify the 64-bit implementation: we don't allow the upper half
registers to be set, and so we can use them to carry state across the
operation.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <1251705011-18636-1-git-send-email-petkovbb@gmail.com>
We have had this convenient macro _ASM_EXTABLE() to generate exception
table entry in inline assembly. Make it also usable for pure
assembly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add 32-bit versions of the combined CFI macros, equivalent to the
64-bit ones except, obviously, operating on 32-bit stack words.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
fbd8b1819e turns off the bit for
/proc/cpuinfo. However, a proper/full fix would be to additionally
turn off the bit in the CPUID output so that future callers get
correct CPU features info.
Do that by basically reversing what the BIOS wrongfully does at boot.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1251705011-18636-3-git-send-email-petkovbb@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
native_{rdmsr,wrmsr}_safe_regs are two new interfaces which allow
presetting of a subset of eight x86 GPRs before executing the rd/wrmsr
instructions. This is needed at least on AMD K8 for accessing an erratum
workaround MSR.
Originally based on an idea by H. Peter Anvin.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <1251705011-18636-1-git-send-email-petkovbb@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
boot_cpu_physical_apicid is a global variable and used as function
argument as well. Rename the function arguments to avoid confusion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The proposed Moorestown support patches use an extra feature flag
mechanism to make the ioapic work w/o an i8259. There is a much
simpler solution.
Most i8259 specific functions are already called dependend on the irq
number less than NR_IRQS_LEGACY. Replacing that constant by a
read_mostly variable which can be set to 0 by the platform setup code
allows us to achieve the same without any special feature flags.
That trivial change allows us to proceed with MRST w/o doing a full
blown overhaul of the ioapic code which would delay MRST unduly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On CRIS, the high address bit controls caching, which means that
we can add a pgprot_noncached() macro that sets this bit in the
address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
m68k has the thread_info structure embedded in its task struct.
Therefore its not possible to implement current_thread_info()
by looking at the stack pointer and do some simple calculations
like most other architectures do it.
To return the thread_info pointer for a task two defines are
used. This works until the spinlock function bodies get moved
into an own header file and CONFIG_SPINLOCK_DEBUG is turned on.
That results into this compile error:
In file included from include/linux/spinlock.h:378,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:54,
from arch/m68k/kernel/asm-offsets.c:12:
include/linux/spinlock_api_smp.h: In function '__spin_unlock_irq':
include/linux/spinlock_api_smp.h:371: error: 'current' undeclared (first use in this function)
include/linux/spinlock_api_smp.h:371: error: (Each undeclared identifier is reported only once
include/linux/spinlock_api_smp.h:371: error: for each function it appears in.)
Including asm/current.h to asm-offsets.c wouldn't help since
the definition of struct task is needed. So we end up with ugly
header file include dependencies.
To solve this calculate the offset of the thread_info structure
into the task struct in asm-offsets.h and use the offset in
task_thread_info(). This works just like it does for IA64 as
well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Horst Hartmann <horsth@linux.vnet.ibm.com>
Cc: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <20090831124417.329662275@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For cuImage format it's necessary to provide clock fixups since u-boot will
not pass necessary clock frequency into the dtb included into cuImage so we
implement the clock fixups as defined in the technical documentation for the
board and update header file with the basic register definitions.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the ESTeem 195E Hotfoot SBC.
There are several variants of the SBC deployed, single/dual
ethernet+serial, and also 4MB/8MB flash variations. In the interest of
having a single kernel image boot on all boards, the cuboot shim detects
the differences and mangles the DTS tree appropriately.
With the exception of the CF interface that was never populated on
production boards, this code/DTS supports all boardpop options.
Signed-off-by: Solomon Peachy <solomon@linux-wlan.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds NOR MTD support and I2C HWMON support for the AD7414
to the AMCC Arches defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds some nodes to the AMCC Arches dts:
- L2 cache support
- NOR FLASH mapping with default partitioning
- I2C HWMON device (AD7414)
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Moorestown MID devices need to be detected early in the boot process
to setup and do not call x86_default_early_setup as there is no EBDA
region to reserve.
[ Copied the minimal code from Jacobs latest MRST series ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jacob Pan <jacob.jun.pan@intel.com>
x86 bootprotocol 2.07 has introduced hardware_subarch ID in the boot
parameters provided by FW. We use it to identify Moorestown platforms.
[ tglx: Cleanup and paravirt fix ]
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Platforms like Moorestown require early setup and want to avoid the
call to reserve_ebda_region. The x86_init override is too late when
the MRST detection happens in setup_arch. Move the default i386
x86_init overrides and the call to reserve_ebda_region into a separate
function which is called as the default of a switch case depending on
the hardware_subarch id in boot params. This allows us to add a case
for MRST and let MRST have its own early setup function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We do not need the TSC before late_time_init. Move the tsc_init to the
late time init code so we can also utilize HPET for calibration (which
we claimed to do but never did except in some older kernel
version). This also helps Moorestown to calibrate the TSC with the
AHBT timer which needs to be initialized in late_time_init like HPET.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
TSC calibration is modified by the vmware hypervisor and paravirt by
separate means. Moorestown wants to add its own calibration routine as
well. So make calibrate_tsc a proper x86_init_ops function and
override it by paravirt or by the early setup of the vmware
hypervisor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the code where it's only user is. Also we need to look whether
this hardwired hackery might interfere with perfcounters.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timer and timer irq setup code is identical in 32 and 64 bit. Make
it the same formatting as well. Also add the global variables under
the necessary ifdefs to both files.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MCA_bus is constant 0 when CONFIG_MCA=n. So the compiler removes that
code w/o needing an extra #ifdef
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Let the compiler optimize the timer_ack magic away in the 32bit timer
interrupt and put the same code into time_64.c. It's optimized out for
CONFIG_X86_IO_APIC on 32bit and for 64bit because timer_ack is const 0
in both cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
