2.6.34 introduced 'conntrack zones' to deal with cases where packets
from multiple identical networks are handled by conntrack/NAT. Packets
are looped through veth devices, during which they are NATed to private
addresses, after which they can continue normally through the stack
and possibly have NAT rules applied a second time.
This works well, but is needlessly complicated for cases where only
a single SNAT/DNAT mapping needs to be applied to these packets. In that
case, all that needs to be done is to assign each network to a seperate
zone and perform NAT as usual. However this doesn't work for packets
destined for the machine performing NAT itself since its corrently not
possible to configure SNAT mappings for the LOCAL_IN chain.
This patch adds a new INPUT chain to the NAT table and changes the
targets performing SNAT to be usable in that chain.
Example usage with two identical networks (192.168.0.0/24) on eth0/eth1:
iptables -t raw -A PREROUTING -i eth0 -j CT --zone 1
iptables -t raw -A PREROUTING -i eth0 -j MARK --set-mark 1
iptables -t raw -A PREROUTING -i eth1 -j CT --zone 2
iptabels -t raw -A PREROUTING -i eth1 -j MARK --set-mark 2
iptables -t nat -A INPUT -m mark --mark 1 -j NETMAP --to 10.0.0.0/24
iptables -t nat -A POSTROUTING -m mark --mark 1 -j NETMAP --to 10.0.0.0/24
iptables -t nat -A INPUT -m mark --mark 2 -j NETMAP --to 10.0.1.0/24
iptables -t nat -A POSTROUTING -m mark --mark 2 -j NETMAP --to 10.0.1.0/24
iptables -t raw -A PREROUTING -d 10.0.0.0/24 -j CT --zone 1
iptables -t raw -A OUTPUT -d 10.0.0.0/24 -j CT --zone 1
iptables -t raw -A PREROUTING -d 10.0.1.0/24 -j CT --zone 2
iptables -t raw -A OUTPUT -d 10.0.1.0/24 -j CT --zone 2
iptables -t nat -A PREROUTING -d 10.0.0.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A OUTPUT -d 10.0.0.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A PREROUTING -d 10.0.1.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A OUTPUT -d 10.0.1.0/24 -j NETMAP --to 192.168.0.0/24
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing the following command on host:
$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1
Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:
skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
Oops: Exception in kernel mode, sig: 5 [#1]
MPC831x RDB
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
NIP: c01c1840 LR: c01c1840 CTR: c016d918
[...]
NIP [c01c1840] skb_over_panic+0x48/0x5c
LR [c01c1840] skb_over_panic+0x48/0x5c
Call Trace:
[c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
[c0339d60] [c01c3020] skb_put+0x5c/0x60
[c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
[c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc
Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:
status=1400 length=1536
status=1800 length=1541
So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.
This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).
Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds UFO to the list of GSO features with a software
fallback. This allows UFO to be used even if the hardware does
not support it.
In particular, this allows us to test the UFO fallback, as it
has been reported to not work in some cases.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port reset operations and memory add/remove operations need to
be serialized to avoid a kernel deadlock. The deadlock is caused
by calling the napi_disable() function twice.
Therefore we have to employ the dlpar_mem_lock in the ehea_reset_port
function as well
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the eHEA poll function an rmb() is required. Without that some packets
on the receive queue are not seen and thus delayed until the next interrupt
is handled for the same receive queue.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the restriction that only allows connecting to a unix domain
socket identified by unix path that is in the same network namespace.
Crossing network namespaces is always tricky and we did not support
this at first, because of a strict policy of don't mix the namespaces.
Later after Pavel proposed this we did not support this because no one
had performed the audit to make certain using unix domain sockets
across namespaces is safe.
What fundamentally makes connecting to af_unix sockets in other
namespaces is safe is that you have to have the proper permissions on
the unix domain socket inode that lives in the filesystem. If you
want strict isolation you just don't create inodes where unfriendlys
can get at them, or with permissions that allow unfriendlys to open
them. All nicely handled for us by the mount namespace and other
standard file system facilities.
I looked through unix domain sockets and they are a very controlled
environment so none of the work that goes on in dev_forward_skb to
make crossing namespaces safe appears needed, we are not loosing
controll of the skb and so do not need to set up the skb to look like
it is comming in fresh from the outside world. Further the fields in
struct unix_skb_parms should not have any problems crossing network
namespaces.
Now that we handle SCM_CREDENTIALS in a way that gives useable values
across namespaces. There does not appear to be any operational
problems with encouraging the use of unix domain sockets across
containers either.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In unix_skb_parms store pointers to struct pid and struct cred instead
of raw uid, gid, and pid values, then translate the credentials on
reception into values that are meaningful in the receiving processes
namespaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ep93xx core helper function ep93xx_devcfg_set_clear should mask the
clear_bits before setting the new set_bits in case the clear_bits are a
mask value that also includes the set_bits.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a core.c __init function to handle the physmap flash
registration for all the ep93xx platforms. Also, modify all
the ep93xx platforms to use this new function.
This simplifies all the ep93xx platform init code and reduces
the size of the kernel when including multiple ep93xx boards.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Martin Guy <martinwguy@gmail.com>
Acked-by: Hubert Feurstein <hubert.feurstein@contec.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the platform registration for the ep93xx backlight driver that
is now merged.
Since the pwm BRIGHT signal only functions if the video system is
operating, register the backlight when the framebuffer device is
registered.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Start capturing not only the userspace pid, uid and gid values of the
sending process but also the struct pid and struct cred of the sending
process as well.
This is in preparation for properly supporting SCM_CREDENTIALS for
sockets that have different uid and/or pid namespaces at the different
ends.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
scm_send occasionally allocates state in the scm_cookie, so I have
modified netlink_sendmsg to guarantee that when scm_send succeeds
scm_destory will be called to free that state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct pid and struct cred to store the peer credentials on struct
sock. This gives enough information to convert the peer credential
information to a value relative to whatever namespace the socket is in
at the time.
This removes nasty surprises when using SO_PEERCRED on socket
connetions where the processes on either side are in different pid and
user namespaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep the coming code clear and to allow both the sock
code and the scm code to share the logic introduce a
fuction to translate from struct cred to struct ucred.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define what happens when a we view a uid from one user_namespace
in another user_namepece.
- If the user namespaces are the same no mapping is necessary.
- For most cases of difference use overflowuid and overflowgid,
the uid and gid currently used for 16bit apis when we have a 32bit uid
that does fit in 16bits. Effectively the situation is the same,
we want to return a uid or gid that is not assigned to any user.
- For the case when we happen to be mapping the uid or gid of the
creator of the target user namespace use uid 0 and gid as confusing
that user with root is not a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
https://bugzilla.kernel.org/show_bug.cgi?id=16183
The sch_teql module, which can be used to load balance over a set of
underlying interfaces, stopped working after 2.6.30 and has been
broken in all kernels since then for any underlying interface which
requires the addition of link level headers.
The problem is that the transmit routine relies on being able to
access the destination address in the skb in order to do address
resolution once it has decided which underlying interface it is going
to transmit through.
In 2.6.31 the IFF_XMIT_DST_RELEASE flag was introduced, and set by
default for all interfaces, which causes the destination address to be
released before the transmit routine for the interface is called.
The solution is to clear that flag for teql interfaces.
Signed-off-by: Tom Hughes <tom@compton.nu>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard the ACK if we find options that do not match current sysctl
settings.
Previously it was possible to create a connection with sack, wscale,
etc. enabled even if the feature was disabled via sysctl.
Also remove an unneeded call to tcp_sack_reset() in
cookie_check_timestamp: Both call sites (cookie_v4_check,
cookie_v6_check) zero "struct tcp_options_received", hand it to
tcp_parse_options() (which does not change tcp_opt->num_sacks/dsack)
and then call cookie_check_timestamp().
Even if num_sacks/dsacks were changed, the structure is allocated on
the stack and after cookie_check_timestamp returns only a few selected
members are copied to the inet_request_sock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the RCTRL_TS_ENABLE bit was set unconditionally. However, if
the RCTRL_TS_ENABLE is set without TMR_CTRL[TE], the driver does not work
properly on some boards (Anton had problems with the MPC8313ERDB and
MPC8568EMDS).
With this patch the bit will only be set if requested from user space
with the SIOCSHWTSTAMP ioctl command, meaning that time stamping is
disabled during normal operation. Users who are not interested in time
stamps will not experience problems with buggy CPU revisions or
performance drops any more.
The setting of TMR_CTRL[TE] is still up to the user. This is considered
safe because users wanting HW timestamps must initialize the eTSEC clock
first anyway, e.g. with the recently submitted PTP clock driver.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the hard-coded shift values for the MTU timer, since
the different platforms using this has very different running
frequencies doing this dynamically is a better idea. Also take
this opportunity to make a more through shutdown of the MTU
clockevent when requested.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/plat-nomadik/gpio.c: In function 'nmk_gpio_remove':
arch/arm/plat-nomadik/gpio.c:630: warning: ignoring return value of 'gpiochip_remove', declared with attribute warn_unused_result
Because this function is marked __exit and this code can't be built as a
module, this function is never used. So just remove it, fixing the
warning in the process.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the platform driver registration to a core_initcall, instead of an
arch_initcall. This will allow us to use gpio related calls in
init_machine() (which is an arch_initcall) after adding the gpio
platform devices.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a pin configuration API to all pin-related configuration to be
specified with a single macro and groups of pins to be configured
at one go. Based on the PXA MFP implementation.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ->direction_output() callback needs to set the value it was passed,
in addition to setting the direction as output. On this peripheral, we
can't set the value before setting the direction, so set it after.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new IA32_ENERGY_PERF_BIAS MSR allows system software to give
hardware a hint whether OS policy favors more power saving,
or more performance. This allows the OS to have some influence
on internal hardware power/performance tradeoffs where the OS
has previously had no influence.
The support for this feature is indicated by CPUID.06H.ECX.bit3,
as documented in the Intel Architectures Software Developer's Manual.
This patch discovers support of this feature and displays it
as "epb" in /proc/cpuinfo.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <alpine.LFD.2.00.1006032310160.6669@localhost.localdomain>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
regression introduced by b8d92c9c14
In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function
this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed RX descriptor functions against the HAL sources. Some minor changes:
- check size before making changes to the descriptor
- whitespace
- add comments about 5210 timestamps. this needs to be adressed later!
- FIFO overrun error only available on 5210
- rs_phyerr should not be OR'ed
- clear the whole ath5k_rx_status structure before using, instead of
zeroing specific fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.
Add 5211 specific frame types.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
