The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.
sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.
sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change mach-jive to use gpiolib for the GPIO lines that are directly
manipulated by it.
Note, we ignore any errors from gpio_request(), unlikely to see any.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the GPIO banks that are used on the S3C2443 and above to the
list of available GPIOS.
Currently we do not have any limit on the SoC GPIO, so these are
being registered whether the SoC has them or not. It is currently
up to the user not to try and use them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary gpio configuration helper for the devices which
have a single-bit pull-up resistor disabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations
to get ready for removal of the specific code being used by s3c24xx.
Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a
as seen in the header file to correct a build warning.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
...rather than the secType. This allows us to get rid of the MSKerberos
securityEnum. The client just makes a decision at upcall time.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
So that we can reasonably set up the secType based on both the
NegotiateProtocol response and the parsed mount options.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
When CONFIG_BLOCK is not enabled:
fs/logfs/super.c:142: error: implicit declaration of function 'bdev_get_queue'
fs/logfs/super.c:142: error: invalid type argument of '->' (have 'int')
Found by Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joern Engel <joern@logfs.org>
"mac80211: improve IBSS scanning" was missing a hunk.
This adds that hunk as originally intended.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the bad hashes for one Kingston and one Transcend card.
Thanks to komuro for pointing this out.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 6bfff31e77 (libata: kill probe_ent
and related helpers) killed ata_device_add() but didn't remove references
to it from the libata developer's guide.
Commits 9363c3825e (libata: rename SFF
functions) and 5682ed33aa (libata: rename
SFF port ops) renamed the taskfile access methods but didn't update the
developer's guide. Commit c9f75b04ed
(libata: kill ata_noop_dev_select()) didn't update the developer's
guide as well.
The guide also refers to the long gone ata_pio_data_xfer_noirq(),
ata_pio_data_xfer(), and ata_mmio_data_xfer() -- replace those by
the modern ata_sff_data_xfer_noirq(), ata_sff_data_xfer(), and
ata_sff_data_xfer32().
Also, remove the reference to non-existant ata_port_stop()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Function init_kmem_cache_nodes is incorrect when checking upper limitation of
kmalloc_caches. The breakage was introduced by commit
91efd773c7 ("dma kmalloc handling fixes").
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
The patch introduces a serio driver that supports a keyboard serial port found
on the Amstrad Delta videophone board.
After initializing the hardware, the driver reads its input data from a buffer
filled in by the board FIQ (Fast Interrupt Request) handler.
Standard AT keyboard driver (atkbd) will be used on top of the serio layer for
handling the E3 keyboard (called mailboard) connected to the port. Since the
device generated scancodes differ from what the atkbd expects, a custom key
code to scan code table must be loaded from userspace for the keyboard to be
useable.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch adds initialization of FIQ related handlers to the Amstrad Delta
videophone board code. FIQ will be used instead of a traditional IRQ for
processing all GPIO generated interrupts, including a keyboard serial clock
line.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of Amstrad Delta modem utilized GPIO line, interrupt is requested from
standard serial8250 driver code without first requesting the GPIO pin itself.
Even if it works with default OMAP GPIO interrupt handler, it appeared not
compatible with recent, optimized version of the board GPIO FIQ handler,
required for fast processing of interrupts generated by other GPIO pin that a
serial keyboard clock hangs off.
This patch fills the board specific modem initialization routine with common
GPIO line reservation and direction setup.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces an IRQ handler used for processing interrupts generated
by the FIQ handler when it decides there are data ready for processing.
The handler further invokes device specific interrupt routines based on
interrupt source counters passed from the FIQ handler.
The handler setup function is intended to be called from the board
provided init_machine() callback.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: Updated to include linux/io.h instead of plat/io.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces a Fast Interrupt Request (FIQ) handler for Amstrad Delta
(E3) videophone. The handler's purpose is to process interrupts generated by a
GPIO line that a serial keyboard clock hangs off. It collects consecutive bits
into words, pushing them into a buffer, then requests a higher level interrupt
after one or more words are ready for further processing by a keyboard port
driver.
The handler also processes interrupts generated by two other GPIO lines, used
by other on-board supported devices, by simply requesting a higher level
interrupt, that in turn should invoke those device's specific irq handlers.
IRQ12 line, not used by OMAP1510 hardware (described as reserved), has been
choosen as a higher level interrupt source.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Several ARM platforms/machines that use FIQ define their value of FIQ_START.
Since FIQ is not implemented for OMAP yet, this definition is missing from
OMAP header files.
Put an arbitrary value for FIQ_START into plat/irqs.h for OMAP. Even if not
used by the FIQ handler for Amstrad Delta, this is required for successfull
compilation of arch/arm/plat-omap/fiq.c that provides several
usefull functions.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like CONFIG_FB_OMAP prevents somehow mounting root on MMC
at least on zoom3 for multi-omap. Disable CONFIG_FB until the
omap FB code is fixed.
This allows booting omap3_defconfig on various omaps. Tested on
2420-n8x0, 3430-n900, 3630-zoom3 and 4430-blaze. Note that n8x0
still has issues with starting user space because of TLS and
VFP.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multiple Lenovo ThinkPad models with Intel Core i5/i7 CPUs can
successfully suspend/resume once, and then hang on the second s/r
cycle.
We got confirmation that this was due to a BIOS defect. The BIOS
did not properly set SCI_EN coming out of S3. The BIOS guys
hinted that The Other Leading OS ignores the fact that hardware
owns the bit and sets it manually.
In any case, an existing DMI table exists for machines where this
defect is a known problem. Lenovo promise to fix their BIOS, but
for folks who either won't or can't upgrade their BIOS, allow
Linux to workaround the issue.
https://bugzilla.kernel.org/show_bug.cgi?id=15407https://bugs.launchpad.net/ubuntu/+source/linux/+bug/532374
Confirmed by numerous testers in the launchpad bug that using
acpi_sleep=sci_force_enable fixes the issue. We add the machines
to acpisleep_dmi_table[] to automatically enable this workaround.
Cc: stable@kernel.org
Cc: Colin King <colin.king@canonical.com>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":
1 - PPC4xx core reset
2 - PPC4xx chip reset
3 - PPC4xx system reset (default)
This will be used by a new PPC440SPe board port, which needs a "chip
reset" instead of the default "system reset" to be asserted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
There's nastyness in the way we currently handle barriers (and
discards): They're effectively filesystem commands, but they get
processed as BLOCK_PC commands. Unfortunately BLOCK_PC commands are
taken by SCSI to be SG_IO commands and the issuer expects to see and
handle any returned errors, however trivial. This leads to a huge
problem, because the block layer doesn't expect this to happen and any
trivially retryable error on a barrier causes an immediate I/O error
to the filesystem.
The only real way to hack around this is to take the usual class of
offending errors (unit attentions) and make them all retryable in the
case of a REQ_HARDBARRIER. A correct fix would involve a rework of
the entire block and SCSI submit system, and so is out of scope for a
quick fix.
Cc: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some arrays are giving I/O errors with ext3 filesystems when
SYNCHRONIZE_CACHE gets a UNIT_ATTENTION. What is happening is that
these commands have no retries, so the UNIT_ATTENTION causes the
barrier to fail. We should be enable retries here to clear any
transient error and allow the barrier to succeed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
When more than one header is included under CREATE_TRACE_POINTS
the DECLARE_TRACE() macro is not defined back to its original meaning
and the second include will fail to initialize the TRACE_EVENT()
and DECLARE_TRACE() correctly.
To fix this the tracepoint.h file moves the define of DECLARE_TRACE()
out of the #ifdef _LINUX_TRACEPOINT_H protection (just like the
define of the TRACE_EVENT()). This way the define_trace.h will undef
the DECLARE_TRACE() at the end and allow new headers to start
from scratch.
This patch also requires fixing the include/events/napi.h
It currently uses DECLARE_TRACE() and should be converted to a TRACE_EVENT()
format. But I'll leave that change to the authors of that file.
But since the napi.h file depends on using the CREATE_TRACE_POINTS
and does not define its own DEFINE_TRACE() it must use the define_trace.h
method instead.
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The s3c24xx_mci_set_platdata() is init time only, so should
be marked as __init
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Setting s3c2410fb_mach_info displays field with a struct marked as __initdata
means it won't be available later for ioctls like FBIOPUT_VSCREENINFO and they
will fail. Copying in s3c24xx_fb_set_platdata() is fixing this issue.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The touchscreen is using the adc device so it needs to be in the device
list
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
