The slot_width is a property for the bus while the constraint for
SNDRV_PCM_HW_PARAM_SAMPLE_BITS is for the in memory format.
Applying slot_width constraint to sample_bits works most of the time, but
it will blacklist valid formats in some cases.
With slot_width 24 we can support S24_3LE and S24_LE formats as they both
look the same on the bus, but a a 24 constraint on sample_bits would not
allow S24_LE as it is stored in 32bits in memory.
Implement a simple hw_rule function to allow all formats which require less
or equal number of bits on the bus as slot_width (if configured).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190726064244.3762-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit db51707b9c.
Revert "ASoC: rockchip: i2s: Support mono capture"
Previous discussion in
https://patchwork.kernel.org/patch/10147153/
explains the issue of the patch.
While device is configured as 1-ch, hardware is still
generating a 2-ch stream.
When user space reads the data and assumes it is a 1-ch stream,
the rate will be slower by 2x.
Revert the change so 1-ch is not supported.
User space can selectively take one channel data out of two channel
if 1-ch is preferred.
Currently, both channels record identical data.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20190726044202.26866-1-cychiang@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When running McASP as master capture alone will not record any audio unless
a parallel playback stream is running. As soon as the playback stops the
captured data is going to be silent again.
In McASP master mode we need to set the PDIR for the clock pins and fix
the mcasp_set_axr_pdir() to skip the bits in the PDIR registers above
AMUTE.
This went unnoticed as most of the boards uses McASP as slave and neither
of these issues are visible (audible) in those setups.
Fixes: ca3d943334 ("ASoC: davinci-mcasp: Update PDIR (pin direction) register handling")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190725083423.7321-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
apq8016_sbc_parse_of() sets up multiple DAI links, depending on the
number of nodes in the device tree. However, at the moment
CPU and platform components are only allocated for the first link.
This causes an oops when more than one link is defined:
Internal error: Oops: 96000044 [#1] SMP
CPU: 0 PID: 1015 Comm: kworker/0:2 Not tainted 5.3.0-rc1 #4
Call trace:
apq8016_sbc_platform_probe+0x1a8/0x3f0
platform_drv_probe+0x50/0xa0
...
Move the allocation inside the loop to ensure that each link is
properly initialized.
Fixes: 98b232ca9e ("ASoC: qcom: apq8016_sbc: use modern dai_link style")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20190722130352.95874-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In snd_soc_dapm_new_control_unlocked(), a kernel buffer is allocated in
dapm_cnew_widget() to hold the new dapm widget. Then, different actions are
taken according to the id of the widget, i.e., 'w->id'. If any failure
occurs during this process, snd_soc_dapm_new_control_unlocked() should be
terminated by going to the 'request_failed' label. However, the allocated
kernel buffer is not freed on this code path, leading to a memory leak bug.
To fix the above issue, free the buffer before returning from
snd_soc_dapm_new_control_unlocked() through the 'request_failed' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Link: https://lore.kernel.org/r/1563803864-2809-1-git-send-email-wang6495@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_UAPI_HEADER_TEST=y, exported headers are compile-tested to
make sure they can be included from user-space.
Currently, header.h and fw.h are excluded from the test coverage.
To make them join the compile-test, we need to fix the build errors
attached below.
For a case like this, we decided to use __u{8,16,32,64} variable types
in this discussion:
https://lkml.org/lkml/2019/6/5/18
Build log:
CC usr/include/sound/sof/header.h.s
CC usr/include/sound/sof/fw.h.s
In file included from <command-line>:32:0:
./usr/include/sound/sof/header.h:19:2: error: unknown type name ‘uint32_t’
uint32_t magic; /**< 'S', 'O', 'F', '\0' */
^~~~~~~~
./usr/include/sound/sof/header.h:20:2: error: unknown type name ‘uint32_t’
uint32_t type; /**< component specific type */
^~~~~~~~
./usr/include/sound/sof/header.h:21:2: error: unknown type name ‘uint32_t’
uint32_t size; /**< size in bytes of data excl. this struct */
^~~~~~~~
./usr/include/sound/sof/header.h:22:2: error: unknown type name ‘uint32_t’
uint32_t abi; /**< SOF ABI version */
^~~~~~~~
./usr/include/sound/sof/header.h:23:2: error: unknown type name ‘uint32_t’
uint32_t reserved[4]; /**< reserved for future use */
^~~~~~~~
./usr/include/sound/sof/header.h:24:2: error: unknown type name ‘uint32_t’
uint32_t data[0]; /**< Component data - opaque to core */
^~~~~~~~
In file included from <command-line>:32:0:
./usr/include/sound/sof/fw.h:49:2: error: unknown type name ‘uint32_t’
uint32_t size; /* bytes minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:50:2: error: unknown type name ‘uint32_t’
uint32_t offset; /* offset from base */
^~~~~~~~
./usr/include/sound/sof/fw.h:64:2: error: unknown type name ‘uint32_t’
uint32_t size; /* bytes minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:65:2: error: unknown type name ‘uint32_t’
uint32_t num_blocks; /* number of blocks */
^~~~~~~~
./usr/include/sound/sof/fw.h:73:2: error: unknown type name ‘uint32_t’
uint32_t file_size; /* size of file minus this header */
^~~~~~~~
./usr/include/sound/sof/fw.h:74:2: error: unknown type name ‘uint32_t’
uint32_t num_modules; /* number of modules */
^~~~~~~~
./usr/include/sound/sof/fw.h:75:2: error: unknown type name ‘uint32_t’
uint32_t abi; /* version of header format */
^~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190721142308.30306-1-yamada.masahiro@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E says that the headset keypress detection needs the MICBIAS
power in order to report the key events to ensure proper operation
The headset keypress detection needs the MICBIAS power in order to report
the key events all the time as long as MIC is present. So MICBIAS pin
is forced on when a MICROPHONE is detected.
On Veyron Minnie I observed that if the MICBIAS power is not present and
the key press detection is activated (just because it is enabled when you
insert a headset), it randomly reports a keypress on insert.
E.g. (KEY_PLAYPAUSE)
Event: (SW_HEADPHONE_INSERT), value 1
Event: (SW_MICROPHONE_INSERT), value 1
Event: -------------- SYN_REPORT ------------
Event: (KEY_PLAYPAUSE), value 1
Userspace thinks that KEY_PLAYPAUSE is pressed and produces the annoying
effect that the media player starts a play/pause loop.
Note that, although most of the time the key reported is the one
associated with BTN_0, not always this is true. On my tests I also saw
different keys reported
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20190719173929.24065-1-enric.balletbo@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When sample rate of TX is different with sample rate of RX in
async mode, the MFreq selection will be wrong.
For example, sysclk = 24.576MHz, TX rate = 96000Hz, RX rate = 48000Hz.
Then ratio of TX = 256, ratio of RX = 512, For MFreq is shared by TX
and RX instance, the correct value of MFreq is 2 for both TX and RX.
But original method will cause MFreq = 0 for TX, MFreq = 2 for RX.
If TX is started after RX, RX will be impacted, RX work abnormal with
MFreq = 0.
This patch is to select proper MFreq value according to TX rate and
RX rate.
Fixes: 0c516b4ff8 ("ASoC: cs42xx8: Add codec driver support for CS42448/CS42888")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/20190716094547.46787-1-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM uses snd_soc_dapm_dai_get_connected_widgets to build a
list of the widgets connected to a specific front end DAI so it
can search through this list for available back end DAIs. The
custom_stop_condition was added to is_connected_ep to facilitate this
list not containing more widgets than is necessary. Doing so both
speeds up the DPCM handling as less widgets need to be searched and
avoids issues with CODEC to CODEC links as these would be confused
with back end DAIs if they appeared in the list of available widgets.
custom_stop_condition was implemented by aborting the graph walk
when the condition is triggered, however there is an issue with this
approach. Whilst walking the graph is_connected_ep should update the
endpoints cache on each widget, if the walk is aborted the number
of attached end points is unknown for that sub-graph. When the stop
condition triggered, the original patch ignored the triggering widget
and returned zero connected end points; a later patch updated this
to set the triggering widget's cache to 1 and return that. Both of
these approaches result in inaccurate values being stored in various
end point caches as the values propagate back through the graph,
which can result in later issues with widgets powering/not powering
unexpectedly.
As the original goal was to reduce the size of the widget list passed
to the DPCM code, the simplest solution is to limit the functionality
of the custom_stop_condition to the widget list. This means the rest
of the graph will still be processed resulting in correct end point
caches, but only widgets up to the stop condition will be added to the
returned widget list.
Fixes: 6742064aef ("ASoC: dapm: support user-defined stop condition in dai_get_connected_widgets")
Fixes: 5fdd022c20 ("ASoC: dpcm: play nice with CODEC<->CODEC links")
Fixes: 09464974ea ("ASoC: dapm: Fix to return correct path list in is_connected_ep.")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20190718084333.15598-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c152f8491a ("ASoC: audio-graph-card: fix an use-after-free in
graph_get_dai_id()") fixups use-after-free issue,
but, it need to use "const" for reg. This patch adds it.
We will have below without this patch
LINUX/sound/soc/generic/audio-graph-card.c: In function 'graph_get_dai_id':
LINUX/sound/soc/generic/audio-graph-card.c:87:7: warning: assignment discards\
'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
reg = of_get_property(node, "reg", NULL);
Fixes: c152f8491a ("ASoC: audio-graph-card: fix an use-after-free in graph_get_dai_id()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Wen Yang <wen.yang99@zte.com.cn>
Link: https://lore.kernel.org/r/87sgrd43ja.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 3461473998 ("ASoC: soc-core: support dai_link with
platforms_num != 1") supports multi Platform, and
commit 9f3eb91753 ("ASoC: simple-card-utils: consider CPU-Platform
possibility") removed no Platform from simple-card.
Multi Platform is now checking both Platform name/of_node are NULL case.
But in normal case, DPCM be doesn't have Platform.
asoc_simple_canonicalize_platform() try to use CPU of_node
to Platform (This is needed for DMAEngine platform case),
but it still might be NULL at DPCM be.
This patch try to use no Platform after that if Platform of_node
is still NULL. It can't probe without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87muhmgw2o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
max98357a_daiops_trigger() is possible to be called in atomic context if
the .nonatomic flag is equal to 0 in the DAI links.
When cancel_delayed_work_sync() in max98357a_daiops_trigger() is called
in atomic context, kernel emits the following message: "BUG: sleeping
function called from invalid context".
According to the DT binding document, value less than or equal to 5ms of
sdmod-delay should be sufficient to avoid the pop noise. Use mdelay
(i.e. busy loop) for such low delay should be acceptable.
Fixes: cec5b01f8f ("ASoC: max98357a: avoid speaker pop when playback
startup")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190708141901.68797-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Loud speaker pop happens during playback even when in slience
playback. Specify Max98357a amp delay times to make sure
clocks are always earlier than sdmode on.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have devm_xxx version of snd_soc_register_component,
let's use it.
This patch also removes related empty functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 64ee5067cf ("ASoC: soc-utils: remove dummy Platform") removed
dummy Platform from ALSA SoC, but it is over-kill.
This patch respawn it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 961fb3c206 ("ASoC: rockchip: rk3399_gru_sound: don't select
unnecessary Platform")
Current ALSA SoC avoid to add duplicate component to rtd,
and this driver was selecting CPU component as Platform component.
Thus, above patch removed Platform settings from this driver,
because it assumed these are same component.
But, some CPU driver is using generic DMAEngine, in such case, both
CPU component and Platform component will have same of_node/name.
In other words, there are some components which are different but
have same of_node/name.
In such case, Card driver definitely need to select Platform even
though it is same as CPU.
It is depends on CPU driver, but is difficult to know it from Card driver.
This patch reverts above patch.
Fixes: commit 961fb3c206 ("ASoC: rockchip: rk3399_gru_sound: don't select unnecessary Platform")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
