Just like regular TLMM pin controllers in Qualcomm SoCs, the Low Power
Audio SubSystem (LPASS) Low Power Island (LPI) TLMM blocks share a lot
of properties, so common part can be moved to separate schema to reduce
code duplication and make reviewing easier.
Except the move of common part, this introduces effective changes:
1. To all LPASS LPI bindings: Reference pinmux-node.yaml in each pin
muxing and configuration node, to bring definition of "function" and
"pins" properties.
2. qcom,sc7280-lpass-lpi-pinctrl: Reference pinctrl.yaml in top leve.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231208215534.195854-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Multi-Purpose Pin controller block is part of an SPMI PMIC (which in
turns sits on an SPMI bus) and uses a single value for the register
property that corresponds to its base address.
Clean up the example by adding a parent PMIC node with proper
'#address-cells' and '#size-cells' properties, dropping the incorrect
second register value, adding some newline separators and increasing the
indentation to four spaces.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231130172834.12653-1-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.8-1
* New agnostic driver to support Lunar Lake and newer platforms
* New driver for Intel Meteor Point-S (PCH for Meteor Lake-S)
* Update drivers to use new PM helpers
* Use RAII for locking in a few drivers (Raag, Andy)
* Reduce locking scope in some functions (Raag)
* Miscellaneous cleanups (Raag)
The following is an automated git shortlog grouped by driver:
alderlake:
- Switch to use Intel pin control PM ops
baytrail:
- Simplify code with cleanup helpers
- Move default strength assignment to a switch-case
- Factor out byt_gpio_force_input_mode()
- Fix types of config value in byt_pin_config_set()
broxton:
- Switch to use Intel pin control PM ops
cannonlake:
- Switch to use Intel pin control PM ops
cedarfork:
- Switch to use Intel pin control PM ops
denverton:
- Switch to use Intel pin control PM ops
elkhartlake:
- Switch to use Intel pin control PM ops
emmitsburg:
- Switch to use Intel pin control PM ops
geminilake:
- Switch to use Intel pin control PM ops
icelake:
- Switch to use Intel pin control PM ops
intel:
- Add Intel Meteor Point pin controller and GPIO support
- use the correct _PM_OPS() export macro
- Add a generic Intel pin control platform driver
- Revert "Unexport intel_pinctrl_probe()"
- allow independent COMPILE_TEST
- Refactor intel_pinctrl_get_soc_data()
- Move default strength assignment to a switch-case
- Make PM ops functions static
- Provide Intel pin control wide PM ops structure
jasperlake:
- Switch to use Intel pin control PM ops
lakefield:
- Switch to use Intel pin control PM ops
lewisburg:
- Switch to use Intel pin control PM ops
lynxpoint:
- Simplify code with cleanup helpers
meteorlake:
- Switch to use Intel pin control PM ops
sunrisepoint:
- Switch to use Intel pin control PM ops
tangier:
- simplify locking using cleanup helpers
- Move default strength assignment to a switch-case
- Enable 910 Ohm bias
tigerlake:
- Switch to use Intel pin control PM ops
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung pinctrl drivers changes for v6.8
1. New hardware: Add pin controllers for Samsung ExynosAutov920 and
Google Tensor GS101.
2. Few DT bindings cleanups: add specific compatibles for each device
using generic compatible as fallback. This affects only DTS, no
driver changes are needed.
3. Allow setting affinity on non wake-up external GPIO interrupts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: renesas: Updates for v6.8 (take two)
- Add pinmux groups, power source, and input/output enable support for
Ethernet pins on RZ/G2L SoCs,
- Miscellaneous fixes and improvements.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver supports pinctrl/GPIO hardware found on Intel Meteor Point
(a Meteor Lake PCH) providing users a pinctrl and GPIO interfaces
including GPIO interrupts.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some of the Ethernet pins on RZ/G3S (but also valid for RZ/G2L) need to
have the direction of the IO buffer set as output for Ethernet to work
properly. On RZ/G3S, these pins are P1_0/P7_0, P1_1/P7_1, and can have
the following Ethernet functions: TXC/TX_CLK or TX_CTL/TX_EN.
As the pins supporting output enable are SoC specific, and there is a
limited number of these pins (TXC/TX_CLK and/or TX_CTL/TX_EN), specify
output enable capable port limits in the platform-based configuration
data structure, to ensure proper validation.
The OEN support has been intantiated for RZ/G3S at the moment.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GPIO controller available on RZ/G3S (but also on RZ/G2L) supports
setting the power source for Ethernet pins. Based on the interface b/w
the Ethernet controller and the Ethernet PHY, and on board design, a
specific power source needs to be selected. The GPIO controller
supports 1.8V, 2.5V, and 3.3V power source selection for the Ethernet
pins. This can be selected though the ETHx_POC registers (x={0, 1}).
Adjust the driver to support this, and to do proper instantiation for
the RZ/G3S and RZ/G2L SoCs. On RZ/G2L only the get operation has been
tested at the moment.
While at it, as the power registers on RZ/G2L support access sizes of 8
bits, and these registers on RZ/G3S support access sizes of 8/16/32
bits, replace writel()/readl() on these registers with writeb()/readb().
This should allow us to use the same code on both SoCs w/o any issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On RZ/G3S different Ethernet pins need to be configured with different
settings (e.g. power-source needs to be set, RGMII TXC and TX_CTL pins
need output-enable). Adjust the driver to allow specifying pin
configuration for pinmux groups. With this, DT settings like the
following are taken into account by the driver:
eth0_pins: eth0 {
tx_ctl {
pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>; /* ET0_TX_CTL */
power-source = <1800>;
output-enable;
drive-strength-microamp = <5200>;
};
};
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pinctrl data for ExynosAutov920 SoC.
It has a newly applied pinctrl register layer for ExynosAuto series.
Pinctrl data for ExynosAutoV920 SoC.
- GPA0,GPA1 (10): External wake up interrupt
- GPQ0 (2): SPMI (PMIC I/F)
- GPB0,GPB1,GPB2,GPB3,GPB4,GPB5,GPB6 (47): I2S Audio
- GPH0,GPH1,GPH2,GPH3,GPH4,GPH5,GPH6,GPH8 (49): PCIE, UFS, Ethernet
- GPG0,GPG1,GPG2,GPG3,GPG4,GPG5 (29): General purpose
- GPP0,GPP1,GPP2,GPP3,GPP4,GPP5,GPP6,GPP7,GPP8,GPP9,GPP10 (77): USI
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-3-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
New ExynosAuto series GPIO have a different register structure.
In the existing Exynos series, EINT control register is enumerated after
a specific offset (e.g EXYNOS_GPIO_ECON_OFFSET, EXYNOS_GPIO_EMASK_OFFSET).
However, from ExynosAutov920 SoC, the register that controls EINT belongs
to each GPIO bank, and each GPIO bank has 0x1000 align.
This is a structure to protect the GPIO bank using S2MPU in VM environment,
and will only be applied in ExynosAuto series SoCs.
--------------------------------------------------------------
| Original Exynos | ExynosAuto |
|------------------------------------------------------------|
| 0x0 GPIO_CON | 0x0 GPIO_CON |
| 0x4 GPIO_DAT | 0x4 GPIO_DAT |
| 0x8 GPIO_PUD | 0x8 GPIO_PUD |
| 0xc GPIO_DRV | 0xc GPIO_DRV |
| 0x10 GPIO_CONPDN | 0x10 GPIO_CONPDN |
| 0x14 GPIO_PUDPDN | 0x14 GPIO_PUDPDN |
|----------------------------| 0x18 EINT_CON (per_bank) |
| ... | 0x1c EINT_FLTCON0 (per_bank) |
| ... | 0x20 EINT_FLTCON1 (per_bank) |
| ... | 0x24 EINT_MASK (per_bank) |
| ... | 0x28 EINT_PEND (per_bank) |
|----------------------------|-------------------------------|
| 0x700 EINT_CON (global) | ... |
| 0x800 EINT_FLTCON (global) | ... |
| 0x900 EINT_MASK (global) | ... |
| 0xa00 EINT_FEND (global) | ... |
--------------------------------------------------------------
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-2-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The Lantiq PEF2256 is a framer and line interface component designed to
fulfill all required interfacing between an analog E1/T1/J1 line and the
digital PCM system highway/H.100 bus.
This kind of component can be found in old telecommunication system.
It was used to digital transmission of many simultaneous telephone calls
by time-division multiplexing. Also using HDLC protocol, WAN networks
can be reached through the framer.
This pinmux support handles the pin muxing part (pins RP(A..D) and pins
XP(A..D)) of the PEF2256.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231128132534.258459-5-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A framer is a component in charge of an E1/T1 line interface.
Connected usually to a TDM bus, it converts TDM frames to/from E1/T1
frames. It also provides information related to the E1/T1 line.
The framer framework provides a set of APIs for the framer drivers
(framer provider) to create/destroy a framer and APIs for the framer
users (framer consumer) to obtain a reference to the framer, and
use the framer.
This basic implementation provides a framer abstraction for:
- power on/off the framer
- get the framer status (line state)
- be notified on framer status changes
- get/set the framer configuration
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20231128132534.258459-2-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: remove gpiochip_is_requested()
- provide a safer alternative to gpiochip_is_requested()
- convert all existing users
- remove gpiochip_is_requested()
We have no external users of gpiochip_is_requested(). Let's remove it
and replace its internal calls with direct testing of the REQUESTED flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Rework for_each_requested_gpio_in_range() to use the new helper to
retrieve a dynamically allocated copy of the descriptor label and free
it at the end of each iteration. We need to leverage the CLASS()'
destructor to make sure that the label is freed even when breaking out
of the loop.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
