The Sony drive status bits use active-low logic. The swim_readbit()
function converts that to 'C' logic for readability. Hence, the
sense of the names of the status bit macros should not be inverted.
Mostly they are correct. However, the TWOMEG_DRIVE, MFM_MODE and
TWOMEG_MEDIA macros have inverted sense (like MkLinux). Fix this
inconsistency and make the following patches less confusing.
The same problem affects swim3.c so fix that too.
No functional change.
The FDHD drive status bits are documented in sonydriv.cpp from MAME
and in swimiii.h from MkLinux.
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'eject' shell command may send various different ioctl commands.
This leads to error messages on the console even though the FDEJECT
ioctl succeeds.
~# eject floppy
SWIM floppy_ioctl: unknown cmd 21257
SWIM floppy_ioctl: unknown cmd 1
Don't log an error message for an invalid ioctl, just do as the
swim3 driver does and return -ENOTTY.
Cc: Laurent Vivier <lvivier@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: stable@vger.kernel.org # v4.14+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We ran into an issue with loop and btrfs, where btrfs would complain about
checksum errors. It turns out that is because we don't handle short reads
at all, we just zero fill the remainder. Worse than that, we don't handle
the filling properly, which results in loop trying to advance a single
bio by much more than its size, since it doesn't take chaining into
account.
Handle short reads appropriately, by simply retrying at the new correct
offset. End the remainder of the request with EIO, if we get a 0 read.
Fixes: bc07c10a36 ("block: loop: support DIO & AIO")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can always get at the request from the payload, no need to store
a pointer to it.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When blk_queue_enter() waits for a queue to unfreeze, or unset the
PREEMPT_ONLY flag, do not allow it to be interrupted by a signal.
The PREEMPT_ONLY flag was introduced later in commit 3a0a529971
("block, scsi: Make SCSI quiesce and resume work reliably"). Note the SCSI
device is resumed asynchronously, i.e. after un-freezing userspace tasks.
So that commit exposed the bug as a regression in v4.15. A mysterious
SIGBUS (or -EIO) sometimes happened during the time the device was being
resumed. Most frequently, there was no kernel log message, and we saw Xorg
or Xwayland killed by SIGBUS.[1]
[1] E.g. https://bugzilla.redhat.com/show_bug.cgi?id=1553979
Without this fix, I get an IO error in this test:
# dd if=/dev/sda of=/dev/null iflag=direct & \
while killall -SIGUSR1 dd; do sleep 0.1; done & \
echo mem > /sys/power/state ; \
sleep 5; killall dd # stop after 5 seconds
The interruptible wait was added to blk_queue_enter in
commit 3ef28e83ab ("block: generic request_queue reference counting").
Before then, the interruptible wait was only in blk-mq, but I don't think
it could ever have been correct.
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alan Jenkins <alan.christopher.jenkins@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull overlayfs updates from Miklos Szeredi:
"In addition to bug fixes and cleanups there are two new features from
Amir:
- Consistent inode number support for the case when layers are not
all on the same filesystem (feature is dubbed "xino").
- Optimize overlayfs file handle decoding. This one touches the
exportfs interface to allow detecting the disconnected directory
case"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: update documentation w.r.t "xino" feature
ovl: add support for "xino" mount and config options
ovl: consistent d_ino for non-samefs with xino
ovl: consistent i_ino for non-samefs with xino
ovl: constant st_ino for non-samefs with xino
ovl: allocate anon bdev per unique lower fs
ovl: factor out ovl_map_dev_ino() helper
ovl: cleanup ovl_update_time()
ovl: add WARN_ON() for non-dir redirect cases
ovl: cleanup setting OVL_INDEX
ovl: set d->is_dir and d->opaque for last path element
ovl: Do not check for redirect if this is last layer
ovl: lookup in inode cache first when decoding lower file handle
ovl: do not try to reconnect a disconnected origin dentry
ovl: disambiguate ovl_encode_fh()
ovl: set lower layer st_dev only if setting lower st_ino
ovl: fix lookup with middle layer opaque dir and absolute path redirects
ovl: Set d->last properly during lookup
ovl: set i_ino to the value of st_ino for NFS export
Pull dmi updates from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi_scan: Use lowercase letters for UUID
firmware: dmi_scan: Add DMI_OEM_STRING support to dmi_matches
firmware: dmi_scan: Fix UUID length safety check
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
Pull pwm updates from Thierry Reding:
"This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups all
across the board"
* tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (29 commits)
pwm: rcar: Add suspend/resume support
pwm: rcar: Use PM Runtime to control module clock
dt-bindings: pwm: rcar: Add bindings for R-Car M3N support
pwm: rcar: Fix a condition to prevent mismatch value setting to duty
pwm: sysfs: Use put_device() instead of kfree()
dt-bindings: pwm: sunxi: Add new compatible strings
pwm: sun4i: Simplify controller mapping
pwm: sun4i: Drop unused .has_rdy member
pwm: sun4i: Properly check current state
pwm: Remove depends on AVR32
pwm: stm32: LPTimer: Use 3 cells ->of_xlate()
dt-bindings: pwm-stm32-lp: Add #pwm-cells
pwm: stm32: Protect common prescaler for all channels
pwm: stm32: Remove unused struct device
pwm: mediatek: Improve precision in rate calculation
pwm: mediatek: Remove redundant MODULE_ALIAS entries
pwm: mediatek: Fix up PWM4 and PWM5 malfunction on MT7623
pwm: jz4740: Enable for all Ingenic SoCs
pwm: jz4740: Add support for devicetree
pwm: jz4740: Implement ->set_polarity()
...
Pull apparmor updates from John Johansen:
"Features:
- add base infrastructure for socket mediation. ABI bump and
additional checks to ensure only v8 compliant policy uses socket af
mediation.
- improve and cleanup dfa verification
- improve profile attachment logic
- improve overlapping expression handling
- add the xattr matching to the attachment logic
- improve signal mediation handling with stacked labels
- improve handling of no_new_privs in a label stack
Cleanups and changes:
- use dfa to parse string split
- bounded version of label_parse
- proper line wrap nulldfa.in
- split context out into task and cred naming to better match usage
- simplify code in aafs
Bug fixes:
- fix display of .ns_name for containers
- fix resource audit messages when auditing peer
- fix logging of the existence test for signals
- fix resource audit messages when auditing peer
- fix display of .ns_name for containers
- fix an error code in verify_table_headers()
- fix memory leak on buffer on error exit path
- fix error returns checks by making size a ssize_t"
* tag 'apparmor-pr-2018-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor: (36 commits)
apparmor: fix memory leak on buffer on error exit path
apparmor: fix dangling symlinks to policy rawdata after replacement
apparmor: Fix an error code in verify_table_headers()
apparmor: fix error returns checks by making size a ssize_t
apparmor: update MAINTAINERS file git and wiki locations
apparmor: remove POLICY_MEDIATES_SAFE
apparmor: add base infastructure for socket mediation
apparmor: improve overlapping domain attachment resolution
apparmor: convert attaching profiles via xattrs to use dfa matching
apparmor: Add support for attaching profiles via xattr, presence and value
apparmor: cleanup: simplify code to get ns symlink name
apparmor: cleanup create_aafs() error path
apparmor: dfa split verification of table headers
apparmor: dfa add support for state differential encoding
apparmor: dfa move character match into a macro
apparmor: update domain transitions that are subsets of confinement at nnp
apparmor: move context.h to cred.h
apparmor: move task related defines and fns to task.X files
apparmor: cleanup, drop unused fn __aa_task_is_confined()
apparmor: cleanup fixup description of aa_replace_profiles
...
Pull block fixes from Jens Axboe:
"Followup fixes for this merge window. This contains:
- Series from Ming, fixing corner cases in our CPU <-> queue mapping.
This triggered repeated warnings on especially s390, but I also hit
it in cpu hot plug/unplug testing while doing IO on NVMe on x86-64.
- Another fix from Ming, ensuring that we always order budget and
driver tag identically, avoiding a deadlock on QD=1 devices.
- Loop locking regression fix from this merge window, from Omar.
- Another loop locking fix, this time missing an unlock, from Tetsuo
Handa.
- Fix for racing IO submission with device removal from Bart.
- sr reference fix from me, fixing a case where disk change or
getevents can race with device removal.
- Set of nvme fixes by way of Keith, from various contributors"
* tag 'for-linus-20180413' of git://git.kernel.dk/linux-block: (28 commits)
nvme: expand nvmf_check_if_ready checks
nvme: Use admin command effects for admin commands
nvmet: fix space padding in serial number
nvme: check return value of init_srcu_struct function
nvmet: Fix nvmet_execute_write_zeroes sector count
nvme-pci: Separate IO and admin queue IRQ vectors
nvme-pci: Remove unused queue parameter
nvme-pci: Skip queue deletion if there are no queues
nvme: target: fix buffer overflow
nvme: don't send keep-alives to the discovery controller
nvme: unexport nvme_start_keep_alive
nvme-loop: fix kernel oops in case of unhandled command
nvme: enforce 64bit offset for nvme_get_log_ext fn
sr: get/drop reference to device in revalidate and check_events
blk-mq: Revert "blk-mq: reimplement blk_mq_hw_queue_mapped"
blk-mq: Avoid that submitting a bio concurrently with device removal triggers a crash
backing: silence compiler warning using __printf
blk-mq: remove code for dealing with remapping queue
blk-mq: reimplement blk_mq_hw_queue_mapped
blk-mq: don't check queue mapped in __blk_mq_delay_run_hw_queue()
...
Pull more i2c updates from Wolfram Sang:
- hot bugfix for i801 to make laptops with strange BIOS reboot again
when using SMBUS Host notify
- change to MAINTAINERS creating a specific fallback entry for I2C host
drivers and settings its status to "Odd fixes"
- a long overdue param checking for the I2C core
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: add param sanity check to i2c_transfer()
MAINTAINERS: add maintainer for Renesas I2C related drivers
MAINTAINERS: remove me as maintainer for I2C host drivers
i2c: i801: Restore configuration at shutdown
i2c: i801: Save register SMBSLVCMD value only once
Pull arch/sh updates from Rich Felker:
"Fixes for bugs in futex, device tree, and userspace breakpoint traps,
and for PCI issues on SH7786"
* tag 'sh-for-4.17' of git://git.libc.org/linux-sh:
arch/sh: pcie-sh7786: handle non-zero DMA offset
arch/sh: pcie-sh7786: adjust the memory mapping
arch/sh: pcie-sh7786: adjust PCI MEM and IO regions
arch/sh: pcie-sh7786: exclude unusable PCI MEM areas
arch/sh: pcie-sh7786: mark unavailable PCI resource as disabled
arch/sh: pci: don't use disabled resources
arch/sh: make the DMA mapping operations observe dev->dma_pfn_offset
arch/sh: add sh7786_mm_sel() function
sh: fix debug trap failure to process signals before return to user
sh: fix memory corruption of unflattened device tree
sh: fix futex FUTEX_OP_SET op on userspace addresses
Pull more arm64 updates from Will Deacon:
"A few late updates to address some issues arising from conflicts with
other trees:
- Removal of Qualcomm-specific Spectre-v2 mitigation in favour of the
generic SMCCC-based firmware call
- Fix EL2 hardening capability checking, which was bodged to reduce
conflicts with the KVM tree
- Add some currently unused assembler macros for managing SIMD
registers which will be used by some crypto code in the next merge
window"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: assembler: add macros to conditionally yield the NEON under PREEMPT
arm64: assembler: add utility macros to push/pop stack frames
arm64: Move the content of bpi.S to hyp-entry.S
arm64: Get rid of __smccc_workaround_1_hvc_*
arm64: capabilities: Rework EL2 vector hardening entry
arm64: KVM: Use SMCCC_ARCH_WORKAROUND_1 for Falkor BP hardening
Pull more s390 updates from Martin Schwidefsky:
"Three notable larger changes next to the usual bug fixing:
- update the email addresses in MAINTAINERS for the s390 folks to use
the simpler linux.ibm.com domain instead of the old
linux.vnet.ibm.com
- an update for the zcrypt device driver that removes some old and
obsolete interfaces and add support for up to 256 crypto adapters
- a rework of the IPL aka boot code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
s390: correct nospec auto detection init order
s390/zcrypt: Support up to 256 crypto adapters.
s390/zcrypt: Remove deprecated zcrypt proc interface.
s390/zcrypt: Remove deprecated ioctls.
s390/zcrypt: Make ap init functions static.
MAINTAINERS: update s390 maintainers email addresses
s390/ipl: remove reipl_method and dump_method
s390/ipl: correct kdump reipl block checksum calculation
s390/ipl: remove non-existing functions declaration
s390: assume diag308 set always works
s390/ipl: avoid adding scpdata to cmdline during ftp/dvd boot
s390/ipl: correct ipl parmblock valid checks
s390/ipl: rely on diag308 store to get ipl info
s390/ipl: move ipl_flags to ipl.c
s390/ipl: get rid of ipl_ssid and ipl_devno
s390/ipl: unite diag308 and scsi boot ipl blocks
s390/ipl: ensure loadparm valid flag is set
s390/qdio: lock device while installing IRQ handler
s390/qdio: clear intparm during shutdown
s390/ccwgroup: require at least one ccw device
...
OEM strings are defined by each OEM and they contain customized and
useful OEM information. Supporting it provides more flexible uses of
the dmi_matches function.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The test which ensures that the DMI type 1 structure is long enough
to hold the UUID is off by one. It would fail if the structure is
exactly 24 bytes long, while that's sufficient to hold the UUID.
I don't expect this bug to cause problem in practice because all
implementations I have seen had length 8, 25 or 27 bytes, in line
with the SMBIOS specifications. But let's fix it still.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a814c3597a ("firmware: dmi_scan: Check DMI structure length")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull drm fixes from Dave Airlie:
"One omap, and one alsa pm fix (we merged the breaking patch via drm
tree).
Otherwise it's two bunches of amdgpu fixes, removing an unneeded file,
some DC fixes, HDMI audio regression fix, and some vega12 fixes"
* tag 'drm-fixes-for-v4.17-rc1' of git://people.freedesktop.org/~airlied/linux: (27 commits)
Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
drm/amd/display: Fix regamma not affecting full-intensity color values
drm/amd/display: Fix FBC text console corruption
drm/amd/display: Only register backlight device if embedded panel connected
drm/amd/display: fix brightness level after resume from suspend
drm/amd/display: HDMI has no sound after Panel power off/on
drm/amdgpu: add MP1 and THM hw ip base reg offset
drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
drm/radeon: add PX quirk for Asus K73TK
drm/omap: fix crash if there's no video PLL
drm/amdgpu: Fix memory leaks at amdgpu_init() error path
drm/amdgpu: Fix PCIe lane width calculation
drm/radeon: Fix PCIe lane width calculation
drm/amdgpu/si: implement get/set pcie_lanes asic callback
drm/amdgpu: Add support for SRBM selection v3
Revert "drm/amdgpu: Don't change preferred domian when fallback GTT v5"
drm/amd/powerply: fix power reading on Fiji
drm/amd/powerplay: Enable ACG SS feature
drm/amdgpu/sdma: fix mask in emit_pipeline_sync
...
Pull tracing fixes from Steven Rostedt:
"A few clean ups and bug fixes:
- replace open coded "ARRAY_SIZE()" with macro
- updates to uprobes
- bug fix for perf event filter on error path"
* tag 'trace-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Enforce passing in filter=NULL to create_filter()
trace_uprobe: Simplify probes_seq_show()
trace_uprobe: Use %lx to display offset
tracing/uprobe: Add support for overlayfs
tracing: Use ARRAY_SIZE() macro instead of open coding it
Pull PCI fixes from Bjorn Helgaas:
- mark Extended Tags as broken on Broadcom HT1100 and HT2000 Root Ports
to fix drm/Xorg hangs and unresponsive keyboards (Sinan Kaya)
- remove useless messages during resource reassignment (Desnes A. Nunes
do Rosario)
* tag 'pci-v4.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove messages about reassigning resources
PCI: Mark Broadcom HT1100 and HT2000 Root Port Extended Tags as broken
Pull parisc updates from Helge Deller:
- fix panic when halting system via "shutdown -h now"
- drop own coding in favour of generic CONFIG_COMPAT_BINFMT_ELF
implementation
- add FPE_CONDTRAP constant: last outstanding parisc-specific cleanup
for Eric Biedermans siginfo patches
- move some functions to .init and some to .text.hot linker sections
* 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent panic at system halt
parisc: Switch to generic COMPAT_BINFMT_ELF
parisc: Move cache flush functions into .text.hot section
parisc/signal: Add FPE_CONDTRAP for conditional trap handling
On SuperH, the base of the physical memory might be different from
zero. In this case, PCI address zero will map to a non-zero physical
address. In order to make sure that the DMA mapping API takes care of
this DMA offset, we must fill in the dev->dma_pfn_offset field for PCI
devices. This gets done in the pcibios_bus_add_device() hook, called
for each new PCI device detected.
The dma_pfn_offset global variable is re-calculated for every PCI
controller available on the platform, but that's not an issue because
its value will each time be exactly the same, as it only depends on
the memory start address and memory size.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The code setting up the PCI -> SuperHighway mapping doesn't take into
account the fact that the address stored in PCIELARx must be aligned
with the size stored in PCIELAMRx.
For example, when your physical memory starts at 0x0800_0000 (128 MB),
a size of 64 MB or 128 MB is fine. However, if you have 256 MB of
memory, it doesn't work because the base address is not aligned on the
size.
In such situation, we have to round down the base address to make sure
it is aligned on the size of the area. For for a 0x0800_0000 base
address with 256 MB of memory, we will round down to 0x0, and extend
the size of the mapping to 512 MB.
This allows the mapping to work on platforms that have 256 MB of
RAM. The current setup would only work with 128 MB of RAM or less.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.
The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.
It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.
This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).
Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.
The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.
In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.
Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".
Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.
However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.
In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.
This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
The SH7786 has different physical memory layout configurations,
configurable through the MMSELR register. The configuration is
typically defined by the bootloader, so Linux generally doesn't care.
Except that depending on the configuration, some PCI MEM areas may or
may not be available. This commit adds a helper function that allows
to retrieve the current physical memory layout configuration. It will
be used in a following patch to exclude unusable PCI MEM areas during
the PCI initialization.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Rich Felker <dalias@libc.org>
When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.
Signed-off-by: Rich Felker <dalias@libc.org>
unflatten_device_tree() makes use of memblock allocation, and
therefore must be called before paging_init() migrates the memblock
allocation data to the bootmem framework. Otherwise the record of the
allocation for the expanded device tree will be lost, and will
eventually be clobbered when allocated for another use.
Signed-off-by: Rich Felker <dalias@libc.org>
Commit 00b73d8d1b ("sh: add working futex atomic ops on userspace
addresses for smp") changed the futex_atomic_op_inuser function to
use a loop. In case of the FUTEX_OP_SET op with a userspace address
containing a value different of 0, this loop is an endless loop.
Fix that by loading the value of oldval from the userspace before doing
the cmpxchg op, also for the FUTEX_OP_SET case.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Rich Felker <dalias@libc.org>
- Add a PX quirk for radeon
- Fix flickering and stability issues with DC on some platforms
- Fix HDMI audio regression
- Few other misc DC and base driver fixes
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
drm/amd/display: Fix regamma not affecting full-intensity color values
drm/amd/display: Fix FBC text console corruption
drm/amd/display: Only register backlight device if embedded panel connected
drm/amd/display: fix brightness level after resume from suspend
drm/amd/display: HDMI has no sound after Panel power off/on
drm/amdgpu: add MP1 and THM hw ip base reg offset
drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
drm/radeon: add PX quirk for Asus K73TK
omap: Fix crash on AM4 EVM, and all OMAP2/3 boards (Tomi)
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
* tag 'drm-misc-next-fixes-2018-04-11' of git://anongit.freedesktop.org/drm/drm-misc:
drm/omap: fix crash if there's no video PLL
Pull more xfs updates from Darrick Wong:
"Most of these are code cleanups, but there are a couple of notable
use-after-free bug fixes.
This series has been run through a full xfstests run over the week and
through a quick xfstests run against this morning's master, with no
major failures reported.
- clean up unnecessary function call parameters
- fix a use-after-free bug when aborting logging intents
- refactor filestreams state data to avoid use-after-free bug
- fix incorrect removal of cow extents when truncating extended
attributes.
- refactor open-coded __set_page_dirty in favor of using vfs
function.
- fix a deadlock when fstrim and fs shutdown race"
* tag 'xfs-4.17-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
Force log to disk before reading the AGF during a fstrim
Export __set_page_dirty
xfs: only cancel cow blocks when truncating the data fork
xfs: non-scrub - remove unused function parameters
xfs: remove filestream item xfs_inode reference
xfs: fix intent use-after-free on abort
xfs: Remove "committed" argument of xfs_dir_ialloc
Pull more gfs2 updates from Bob Peterson:
"We decided to request the latest three patches to be merged into this
merge window while it's still open.
- The first patch adds a new function to lockref:
lockref_put_not_zero
- The second patch fixes GFS2's glock dump code so it uses the new
lockref function. This fixes a problem whereby lock dumps could
miss glocks.
- I made a minor patch to update some comments and fix the lock
ordering text in our gfs2-glocks.txt Documentation file"
* tag 'gfs2-4.17.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
GFS2: Minor improvements to comments and documentation
gfs2: Stop using rhashtable_walk_peek
lockref: Add lockref_put_not_zero
Pull NFS client updates from Anna Schumaker:
"Stable bugfixes:
- xprtrdma: Fix corner cases when handling device removal # v4.12+
- xprtrdma: Fix latency regression on NUMA NFS/RDMA clients # v4.15+
Features:
- New sunrpc tracepoint for RPC pings
- Finer grained NFSv4 attribute checking
- Don't unnecessarily return NFS v4 delegations
Other bugfixes and cleanups:
- Several other small NFSoRDMA cleanups
- Improvements to the sunrpc RTT measurements
- A few sunrpc tracepoint cleanups
- Various fixes for NFS v4 lock notifications
- Various sunrpc and NFS v4 XDR encoding cleanups
- Switch to the ida_simple API
- Fix NFSv4.1 exclusive create
- Forget acl cache after setattr operation
- Don't advance the nfs_entry readdir cookie if xdr decoding fails"
* tag 'nfs-for-4.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (47 commits)
NFS: advance nfs_entry cookie only after decoding completes successfully
NFSv3/acl: forget acl cache after setattr
NFSv4.1: Fix exclusive create
NFSv4: Declare the size up to date after it was set.
nfs: Use ida_simple API
NFSv4: Fix the nfs_inode_set_delegation() arguments
NFSv4: Clean up CB_GETATTR encoding
NFSv4: Don't ask for attributes when ACCESS is protected by a delegation
NFSv4: Add a helper to encode/decode struct timespec
NFSv4: Clean up encode_attrs
NFSv4; Clean up XDR encoding of type bitmap4
NFSv4: Allow GFP_NOIO sleeps in decode_attr_owner/decode_attr_group
SUNRPC: Add a helper for encoding opaque data inline
SUNRPC: Add helpers for decoding opaque and string types
NFSv4: Ignore change attribute invalidations if we hold a delegation
NFS: More fine grained attribute tracking
NFS: Don't force unnecessary cache invalidation in nfs_update_inode()
NFS: Don't redirty the attribute cache in nfs_wcc_update_inode()
NFS: Don't force a revalidation of all attributes if change is missing
NFS: Convert NFS_INO_INVALID flags to unsigned long
...
Pull vfs thaw updates from Al Viro:
"An ancient series that has fallen through the cracks in the previous
cycle"
* 'work.thaw' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
buffer.c: call thaw_super during emergency thaw
vfs: factor sb iteration out of do_emergency_remount
Pull AFS updates from Al Viro:
"The AFS series posted by dhowells depended upon lookup_one_len()
rework; now that prereq is in the mainline, that series had been
rebased on top of it and got some exposure and testing..."
* 'afs-dh' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Do better accretion of small writes on newly created content
afs: Add stats for data transfer operations
afs: Trace protocol errors
afs: Locally edit directory data for mkdir/create/unlink/...
afs: Adjust the directory XDR structures
afs: Split the directory content defs into a header
afs: Fix directory handling
afs: Split the dynroot stuff out and give it its own ops tables
afs: Keep track of invalid-before version for dentry coherency
afs: Rearrange status mapping
afs: Make it possible to get the data version in readpage
afs: Init inode before accessing cache
afs: Introduce a statistics proc file
afs: Dump bad status record
afs: Implement @cell substitution handling
afs: Implement @sys substitution handling
afs: Prospectively look up extra files when doing a single lookup
afs: Don't over-increment the cell usage count when pinning it
afs: Fix checker warnings
vfs: Remove the const from dir_context::actor
