Pull "Device Tree clean up for LPC18xx platform" from Joachim Eastwood:
* Removal of skeleton.dtsi from the common armv7-m dtsi together
with lpc18xx and efm32 platforms.
* Fix for unit address warnings from the dtc on lpc18xx/efm32.
That is made possible with skeleton.dtsi gone.
* tag 'lpc18xx_dts_for_4.9_part2' of https://github.com/manabian/linux-lpc:
ARM: dts: efm32: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: lpc18xx: remove skeleton.dtsi include and fix unit address warnings
ARM: dts: armv7-m: remove skeleton.dtsi include
Pull "mvebu dt for 4.9 (part 1)" from Gregory CLEMENT:
- update for Armada XP/38x allowing using direct access SPI
- various improvement for Armada 39x platforms
- add pinctrl information for NANd on Armada 38x
- fix the kirkwood based Openblock A6 external GPIO pins
* tag 'mvebu-dt-4.9-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: fix reference to a390 spi controller
ARM: dts: armada-38x: Add NAND pinctrl information
ARM: dts: kirkwood: Fix Openblock A6 external GPIO pins
ARM: dts: mvebu: armada-395-gp: add support for the Armada 395 GP Board
ARM: dts: mvebu: armada-390-db: add support for the Armada 390 DB board
ARM: dts: mvebu: armada-398-db: enable supported usb interfaces
ARM: dts: mvebu: armada-398: update the dtsi about missing interfaces
ARM: dts: mvebu: armada-395: add support for the Armada 395 SoC family
ARM: dts: mvebu: armada-39x: enable rtc for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: add missing nodes describing GPIO's
ARM: dts: mvebu: armada-39x: enable watchdog for all Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable the thermal sensor in Armada-39x SoCs
ARM: dts: mvebu: armada-39x: enable PMU, CA9 SoC Controller and Coherency fabric
ARM: dts: mvebu: armada-39x: update the SDHCI node on Armada 39x
ARM: dts: mvebu: armada-390: add missing compatibility string and bracket
ARM: dts: mvebu: a385-db-ap: add default partition description for NAND
ARM: dts: mvebu: a385-db-ap: enable USB (orion-ehci) port
ARM: dts: mvebu: armada-370-xp: Add MBus mappings for all SPI devices
ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node
ARM: dts: mvebu: Add SPI1 pinctrl defines for Armada XP
As noted in commit 3ebee5a2e1 ("arm64: dts: kill skeleton.dtsi"),
there are a number of problems with skeleton.dtsi, and it would be
prefereable to remove it entirely. As there are a large number of
existing users, fixing these up will take a while.
This patch adds a note to arm's skeleton.dtsi noting that this is the
case, to make this more obvious and hopefully minimize new uptake of
skeleton.dtsi in the mean time.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "DTS related changes for omaps for v4.9 merge window" from Tony Lindgren:
- Update elm phandle for am335x
- Fix overo NAND gpmc ranges, this has always been broken so it can
wait for the merge window
- Fix NAND and use NAND ready pin for logicpd gpmc, this can wait too
as it's been using the older configration since the dts got added
- A series of dtc warning fixes for unit names
- Keep dcdc3, 5 and 6 enabled during suspend on am347x boards
- Disable DDR regulator during rtc-only/poweroff mode for am437x boards
- Remove redundant regulator compatibles for am437x boards
- Increas QSPI max frequency for dra7 boards
- Enable QSPI for am57xx-idk-common
- Enable am335x-wega audio support
- Workaround for i845 for dra7
- Update binding for logicpd boards
- Add gpio-decoder nodes for am335x-icev2 board
- Add linux,pci-domain property for dra7
- Fix dra7 clock data gmac_gmii_ref_clk_div and related clock tree
entries, these can wait for merge window as Ethernet works on dra7
- A series of changes to drop skeleton.dtsi because of dtc warnings
* tag 'omap-for-v4.9/dt-pt1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (54 commits)
ARM: dts: dra7: Add missing unit name to memory nodes
ARM: dts: dra62x: Add missing unit name to memory nodes
ARM: dts: dm8168: Add missing unit name to memory nodes
ARM: dts: dm8148: Add missing unit name to memory nodes
ARM: dts: am572x: Add missing unit name to memory nodes
ARM: dts: am4372: Add missing unit name to memory nodes
ARM: dts: am3517: Add missing unit name to memory nodes
ARM: dts: am335x: Add missing unit name to memory nodes
ARM: dts: omap5: Add missing unit name to memory nodes
ARM: dts: omap4: Add missing unit name to memory nodes
ARM: dts: omap3: Add missing unit name to memory nodes
ARM: dts: omap2: Add missing unit name to memory nodes
ARM: dts: am4372: Remove skeleton.dtsi usage
ARM: dts: dra7: Remove skeleton.dtsi usage
ARM: dts: dm816x: Remove skeleton.dtsi usage
ARM: dts: dm814x: Remove skeleton.dtsi usage
ARM: dts: am33xx: Remove skeleton.dtsi usage
ARM: dts: omap5: Remove skeleton.dtsi usage
ARM: dts: omap4: Remove skeleton.dtsi usage
ARM: dts: omap3: Remove skeleton.dtsi usage
...
Merge "UniPhier ARM SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Switch over to PSCI
* Use clock/reset drivers
* Misc
* tag 'uniphier-dt-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add specific compatible to SoC-Glue node
ARM: dts: uniphier: use clock/reset controllers
ARM: dts: uniphier: switch over to PSCI
ARM: dts: uniphier: match DT names to other projects and documents
ARM: dts: uniphier: remove a whitespace after tabs
Merge "Samsung DeviceTree update for v4.9" from Krzysztof Kozlowski:
1. Set chosen serial bitrate which allows proper serial output when
bootloader does pass all the data in command line.
2. Cleanup.
* tag 'samsung-dt-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use 'hpd-gpios' instead of 'hpd-gpio'
ARM: dts: exynos: Use stdout non-deprecated property and add serial options to Odroid XU/XU3/XU4
Merge "Device Tree additions for LPC18xx platform" from Joachim Eastwood:
Small fix for the compatible string for the NXP SE97 I2C chip on the
Hitex Eval board from Guenter and a couple of additional DT properties
for the DWMAC that is need for correct operation.
* tag 'lpc18xx_dts_for_4.9' of https://github.com/manabian/linux-lpc:
ARM: dts: lpc18xx: configure dwmac properly
ARM: dts: lpc4350-hitex-eval: fix binding for SE97 i2c device
Use the cache settings that were determined to give best performance
on artpec-6 typical workloads.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes. Also add missing
device_type to the memory node while at it.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Remove skeleton.dtsi from the common ARM Cortex-M dtsi. This will allow
us to remove skeleton.dtsi on a per platform basis and get rid of the
unit address warning on the memory nodes without getting duplicate memory
nodes.
See 3ebee5a2e1 ("arm64: dts: kill skeleton.dtsi") for additional
reasons not to use the skeleton.dtsi.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Define the Wheat board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When removing the non-existing thermal clock I forgot to remove its
parent from the node's "clocks" property -- this led to a wrong PWM
clock's parent clock.
Fixes: 2a29f9d6fe ("ARM: dts: r8a7794: add MSTP5 clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add RSKRZA1 Device tree bindings Documentation, listing it as a supported
board.
This allows to use checkpatch to validate DTSes referring to the RSKRZA1
board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R8A7792 SoC doesn't have the EtherMAC core, so SMSC LAN89218 Ethernet
chip was used instead on the Wheat debug board; this chip is compatible
with SMSC LAN9115 for which there's a (device tree aware) driver.
Describe the chip in the Wheat device tree unconditionally (the driver
should fail the probe if the debug board isn't connected); enable DHCP and
NFS root in the command line for the kernel boot...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7792 SoC based Wheat board.
The Wheat board itself has no serial ports wired up, the USB serial chips
are situated on a separate debug board and one of them is connected to
SCFI0 -- include unconditional support for it, so that the serial console
can work.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
TSENS is part of GCC, hence add TSENS properties as part of GCC node.
Also add thermal zones and qfprom nodes.
Update GCC bindings doc to mention the possibility of optional TSENS
properties that can be part of GCC node.
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the i2c2 and rmi4 nodes to enable the Synaptics touchscreen found in
the Honami.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- Sata
- HDMI
- 2 x USB2 type A
- micro USB2 type AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force HOST_PORTS_IMPL to 1 by using
ports-implemented DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
On 96board, we can't reuse rgmii1-mdio as the pin pio1 3
( mdint ) is dedicated for user led green 1. So create
rgmii1_mdio_1 for 96board on which only mdio and mdc pins
are useful.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Due to 96board which uses mmc0 node for SD card, the non-removable
property must be moved from STiH407-family to board file for B2120
and B2199 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Add missing pin muxing for I2C2 alternate 2. This
i2c2 pin muxing is dedicated for 96board high speed
expansion connector.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Correct spacing between nodes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
