The GbEth IP will pass through a zero UDP checksum without asserting any
error flags so we do not need to resort to software checksum calculation
in this case.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
For IPv4 packets, the header checksum will always be calculated in software
in the TX path (Documentation/networking/checksum-offloads.rst says "No
offloading of the IP header checksum is performed; it is always done in
software.") so there is no advantage in asking the hardware to also
calculate this checksum.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The hardware checksum value is used as a 16-bit flag, it is zero when
the checksum has been validated and non-zero otherwise. Therefore we
don't need to treat this as an actual __wsum type or call csum_unfold(),
we can just use a u16 pointer.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
We can merge the two if conditions on skb_is_nonlinear(). Since
skb_frag_size_sub() and skb_trim() do not free memory, it is still safe
to access the trimmed bytes at the end of the packet after these calls.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
We do not need to confirm that the protocol is IPv4. If the hardware
encounters an unsupported protocol, it will set the checksum value to
0xFFFF.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
For IPv4 packets, the header checksum will always be checked in software
in the RX path (inet_gro_receive() calls ip_fast_csum() unconditionally)
so there is no advantage in asking the hardware to also calculate this
checksum.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Introduce new constants for the CSR1 (TX) and CSR2 (RX) checksum enable
bits, removing the risk of inconsistency when we change which flags we
enable.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
GCC is not happy with the current code, e.g.:
.../tg3.c:11313:37: error: ‘-txrx-’ directive output may be truncated writing 6 bytes into a region of size between 1 and 16 [-Werror=format-truncation=]
11313 | "%s-txrx-%d", tp->dev->name, irq_num);
| ^~~~~~
.../tg3.c:11313:34: note: using the range [-2147483648, 2147483647] for directive argument
11313 | "%s-txrx-%d", tp->dev->name, irq_num);
When `make W=1` is supplied, this prevents kernel building. Fix it by
increasing the buffer size for IRQ label and use sizeoF() instead of
hard coded constants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Message-ID: <20241016090647.691022-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
There is no longer any reason to implement the mac_select_pcs()
callback in DSA. Returning ERR_PTR(-EOPNOTSUPP) is functionally
equivalent to not providing the function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
In sr_mdio_read() the local variable res is used to store both
little-endian and host byte order values. This prevents Sparse
from helping us by flagging when endian miss matches occur - the
detection process hinges on the type of variables matching the
byte order of values stored in them.
Address this by adding a new local variable, word, to store little-endian
values; change the type of res to int, and use it to store host-byte
order values.
Flagged by Sparse as:
.../sr9700.c:205:21: warning: incorrect type in assignment (different base types)
.../sr9700.c:205:21: expected restricted __le16 [addressable] [usertype] res
.../sr9700.c:205:21: got int
.../sr9700.c:207:21: warning: incorrect type in assignment (different base types)
.../sr9700.c:207:21: expected restricted __le16 [addressable] [usertype] res
.../sr9700.c:207:21: got int
.../sr9700.c:212:16: warning: incorrect type in return expression (different base types)
.../sr9700.c:212:16: expected int
.../sr9700.c:212:16: got restricted __le16 [addressable] [usertype] res
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016-blackbird-le16-v1-1-97ba8de6b38f@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The Realtek RTL8125/RTL8126 NBase-T MAC/PHY chips have internal PHY's
which are register-compatible, at least for the registers we use here.
So let's use just one PHY driver to support all of them.
These internal PHY's exist also as external C45 PHY's, but on the
internal PHY's no access to MMD registers is possible. This can be
used to differentiate between the internal and external version.
As a side effect the drivers for two now external-only drivers don't
require read_mmd/write_mmd hooks any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c57081a6-811f-4571-ab35-34f4ca6de9af@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It should be invalid to delete an rss context while it is being
referenced from an ntuple filter. ethtool core should prevent this
from happening. This patch adds a testcase to verify this behavior.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ntuple filters can specify an rss context to use for packet hashing
and queue selection. When a filter is referencing an rss context, it
should be invalid for that context to be deleted. A list of active
ntuple filters and their associated rss contexts can be compiled by
querying a device's ethtool_ops.get_rxnfc. This patch checks to see if
any ntuple filters are referencing an rss context during context
deletion, and prevents the deletion if the requested context is still
in use.
Signed-off-by: Daniel Zahka <daniel.zahka@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-10-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() and rtnl_register_module() in favour
of rtnl_register_many().
When it succeeds for built-in callers, rtnl_register_many() guarantees
all rtnetlink types in the passed array are supported, and there is no
chance that a part of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-9-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-7-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-6-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20241014201828.91221-5-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will remove rtnl_register() in favour of rtnl_register_many().
When it succeeds, rtnl_register_many() guarantees all rtnetlink types
in the passed array are supported, and there is no chance that a part
of message types is not supported.
Let's use rtnl_register_many() instead.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241014201828.91221-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will replace all rtnl_register() and rtnl_register_module() with
rtnl_register_many().
Currently, rtnl_register() returns nothing and prints an error message
when it fails to register a rtnetlink message type and handlers.
The failure happens only when rtnl_register_internal() fails to allocate
rtnl_msg_handlers[protocol][msgtype], but it's unlikely for built-in
callers on boot time.
rtnl_register_many() unwinds the previous successful registrations on
failure and returns an error, but it will be useless for built-in callers,
especially some subsystems that do not have the legacy ioctl() interface
and do not work without rtnetlink.
Instead of booting up without rtnetlink functionality, let's panic on
failure for built-in rtnl_register_many() callers.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014201828.91221-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Harshitha Ramamurthy says:
====================
gve: adopt page pool
This patchset implements page pool support for gve.
The first patch deals with movement of code to make
page pool adoption easier in the next patch. The
second patch adopts the page pool API. The third patch
adds basic per queue stats which includes page pool
allocation failures as well.
====================
Link: https://patch.msgid.link/20241014202108.1051963-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ignat Korchagin says:
====================
do not leave dangling sk pointers in pf->create functions
Some protocol family create() implementations have an error path after
allocating the sk object and calling sock_init_data(). sock_init_data()
attaches the allocated sk object to the sock object, provided by the
caller.
If the create() implementation errors out after calling sock_init_data(),
it releases the allocated sk object, but the caller ends up having a
dangling sk pointer in its sock object on return. Subsequent manipulations
on this sock object may try to access the sk pointer, because it is not
NULL thus creating a use-after-free scenario.
We have implemented a stable hotfix in commit 6310831433
("net: explicitly clear the sk pointer, when pf->create fails"), but this
series aims to fix it properly by going through each of the pf->create()
implementations and making sure they all don't return a sock object with
a dangling pointer on error.
====================
Link: https://patch.msgid.link/20241014153808.51894-1-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bt_sock_alloc() attaches allocated sk object to the provided sock object.
If rfcomm_dlc_alloc() fails, we release the sk object, but leave the
dangling pointer in the sock object, which may cause use-after-free.
Fix this by swapping calls to bt_sock_alloc() and rfcomm_dlc_alloc().
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241014153808.51894-4-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
