Merge "second bunch of dts changes for 3.18" from Heiko Stubner:
More peripheral support for Rockchip SoCs
- dwc2 usb controllers
- spi controllers
- emmc controller
* tag 'v3.18-rockchip-dts2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Remove "regulator-always-on" in vcc_rmii for Radxa Rock
ARM: dts: rockchip: fix rk3188 emmc pull references
ARM: dts: rockchip: fix swapped Radxa Rock pinctrl references
ARM: dts: rockchip: clean up rk3xxx mmc nodes
ARM: dts: rockchip: add emmc nodes for rk3066 and rk3188
ARM: dts: rockchip: add Cortex-A9 SPI controller nodes
ARM: dts: rockchip: enable usb ports on Radxa Rock
ARM: dts: rockchip: add dwc2 controllers for rk3066 and rk3188
ARM: dts: rockchip: remove rockchip,bus-index from rk3xxx i2c0
ARM: dts: Switch i2c0 to 400kHz on rk3288-evb-rk808
ARM: dts: Add rk808 PMIC to rk3288-evb-rk808
ARM: dts: Add mshc aliases for rk3288
ARM: dts: Add SPI nodes to rk3288
ARM: dts: Enable USB host1(dwc) on rk3288-evb
ARM: dts: add rk3288 dwc2 controller support
ARM: dts: Add sdio0 and sdio1 to the rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "qcom DT changes for v3.18-2" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-2
* Added SDCC nodes on MSM8960/CDP and MSM8660/SURF
* Added I2C and SDCC4/WLAN on APQ8064/IFC6410
* Added I2C on MSM8984/DB8074
* tag 'qcom-dt-for-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: DT: msm8960: Add sdcc nodes
ARM: DT: msm8660: Add sdcc nodes
ARM: DT: apq8064: Add i2c device nodes
ARM: DT: apq8064: add support to sdcc4 for wlan.
ARM: dts: qcom: Add I2C dt node for MSM8974 and DB8074 board
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "qcom DT changes for v3.18" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18
* Added APQ8084 dt support for clocks, serial, pinctrl, and IFC6540 board
* Added IPQ8064 dt support for basic SoC and AP148 board
* Added APQ8064 dt support for pinctrl, reset, SDHC, and multimedia clocks
* Added PMIC 8058 dt support on MSM8660, enables PMIC based power key,
keypad, rtc, and vibrator
* Added PMIC 8921 dt support on MSM8960, enables PMIC based power key,
keypad, and rtc
* tag 'qcom-dt-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: DT: QCOM: apq8064: Add dma support for sdcc node
ARM: DT: apq8064: Add sdcc support via mcci driver.
ARM: dts: qcom: Add 8064 multimedia clock controller node
ARM: DT: APQ8064: Add node for ps_hold function in pinctrl
ARM: DT: APQ8064: Add pinctrl support
ARM: dts: qcom: Add TLMM DT node for APQ8084
ARM: dts: qcom: Add initial IFC6540 board device tree
ARM: dts: msm: Add 8058 PMIC to ssbi bus
ARM: dts: msm: Add 8921 PMIC to ssbi bus
ARM: qcom: Add initial IPQ8064 SoC and AP148 device trees
ARM: dts: qcom: Add APQ8084 serial port DT node
ARM: dts: qcom: Add APQ8084 Global Clock Controller DT node
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap dts changes for v3.18 merge window" from Tony Lindgren:
Changes for .dts files for omaps for v3.18 merge window:
- Updates for gta04 to add gta04a3 model
- Add support for Tehnexion TAO3530 boards
- Regulator names for beaglebone
- Pinctrl related updates for omap5, dra7 and am437
- Model name fix for sbc-t54
- Enable mailbox for various omaps
* tag 'dt-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (291 commits)
ARM: dts: OMAP2+: Add sub mailboxes device node information
ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable
ARM: dts: OMAP5 / DRA7: switch over to interrupts-extended property for UART
ARM: dts: AM437x: switch to compatible pinctrl
ARM: dts: DRA7: switch to compatible pinctrl
ARM: dts: OMAP5: switch to compatible pinctrl
ARM: dts: am335x-boneblack: Add names for remaining regulators
ARM: dts: sbc-t54: fix model property
ARM: dts: omap5.dtsi: add DSS RFBI node
ARM: dts: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based)
ARM: dts: omap3: Add Technexion Thunder support (TAO3530 SOM based)
ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
ARM: OMAP2+: tao3530: Add pdata-quirk for the mmc2 internal clock
ARM: OMAP2+: board-generic: add support for AM57xx family
ARM: dts: dra72-evm: Add tps65917 PMIC node
ARM: dts: dra72-evm: Enable I2C1 node
Linux 3.17-rc3
unicore32: Fix build error
vexpress/spc: fix a build warning on array bounds
spi: sh-msiof: Fix transmit-only DMA transfers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the sdcc nodes to support the SD card controller using pl180
mmci driver. We also add a temporary fixed regulator until the
regulator driver is mainlined.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the sdcc nodes to support the SD card controller using pl180
mmci driver. We also add a temporary fixed regulator until the
regulator driver is mainlined.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
On Rockchip RK3188 SoCs the platform driver emac_rockchip is used. This variant driver
enables this regulator when the device driver is loaded. The phy no longer needs
to be always on.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds i2c pinctrl DT node for IFC6410 board. It also adds
necessary DT support for i2c eeprom which is present on IFC6410.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add support for i2c controller on the DB8074 board. It also adds necessary
DT support for i2c eeprom which is present on DB8074 board.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Fix a copy'n'paste error making the rk3188 emmc pinctrl nodes reference
the pcfg_pull_default setting that is not available on rk3188.
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The host and otg regulator pinctrl settings got swapped, making the host
reference the otg pinctrl and the other way round. The actual pins are
correct (gpio0-3 for host and gpio2-31 for otg).
Reported-by: Naoki FUKAUMI <naobsd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 356649ab6d ("ARM: dts: rockchip: unuse the slot-node and deprecate
the supports-highspeed for dw-mmc") removed the slots but not the #xx-cells
properties describing the subnodes. Do this now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the controller node, pinctrl settings for the customizable pins
and sort the controllers like on rk3288 as emmc, sdmmc, sdio for
handling convenience.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables both the otg and host port and adds the vbus regulators
on the Radxa Rock board. As we don't have phy support yet, the vbus
regulators are added in always-on mode.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is a remnant from the first i2c driver iteration that seems to have
been forgotten and thus made its way into the dtsi. Remove it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The sub-mailbox devices are added to the Mailbox DT nodes on
OMAP2420, OMAP2430, OMAP3, AM33xx, AM43xx, OMAP4 and OMAP5
family of SoCs. This data represents the same mailboxes that
used to be represented in hwmod attribute data previously.
The node name is chosen based on the .name field of
omap_mbox_dev_info structure used in the hwmod data.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support to SD card controller using generic pl180 mmci driver.
This patch also adds temporary fixed regulator to get it going till the actual
regulator is mainlined.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the mmcc node so that we can probe and use the multimedia
clocks on apq8064.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add basic support for the IFC6540 single-board computer boards, that are
based on the APQ8084 SoC. This patch adds the initial device tree and the
neccessary nodes required for enabling the serial port and eMMC.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the PMIC and the sub-devices that are currently supported in
the kernel to the DT.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add the PMIC and the sub-devices that are currently supported in
the kernel to the DT.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
We should be able to talk to the PMIC at 400kHz. No need to talk at
the slow 100kHz.
As measured by ftrace (with a bunch of extra patches, since cpufreq
for rk808 hasn't landed yet):
before this change: cpu0_set_target() => ~500us
after this change: cpu0_set_target() => ~300us
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by Addy Ke <addy.ke@rock-chips.com>
Tested-by Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull "Fourth Round of Renesas ARM Based SoC DT Updates for v3.18" from Simon Horman:
* Add r8a7794 SoC and Alt board device tree
* Correct lager memory map
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-dt4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Initial Alt board device tree
ARM: shmobile: Initial r8a7794 SoC device tree
ARM: shmobile: lager: correct memory map
Pull "arm: dts: Add Altera SDRAM EDAC bindings & devicetree entries" From Dinh Nguyen:
5 of the 6 patches are DTS updates and the 1 patch is updating
the MAINTAINERS entry with my new email address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'socfpga_update_for_v3.18' of git://git.rocketboards.org/linux-socfpga-next:
arm: dts: Add Altera SDRAM EDAC bindings & devicetree entries.
ARM: dts: socfpga: memreserve first 4KB for future system use
ARM: dts: socfpga: Add SD card detect
ARM: dts: socfpga: remove extra alias in the ArriaV devkit
ARM: dts: socfpga: unuse the slot-node and deprecate the supports-highspeed for dw-mmc
MAINTAINERS: update entries for ARM/SOCFPGA platform
Mark rxd as wakeupcapable for 115200n8 no hardware-flow control
configuration. If h/w flow control is being used, then rts/cts
appropriately should be used.
Signed-off-by: Nishanth Menon <nm@ti.com>
We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee1786 ("pinctrl: single: Add support for wake-up interrupts")
that recently got merged. In addition to that we also needed
commit 79d9701559 ("of/irq: create interrupts-extended property")
that's now also merged.
Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that ti,am437-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.
While at it, mark the pinctrl as interrupt controller so that it can
be used with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that ti,dra7-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.
While at it, mark pinctrl as interrupt controller so that it can be used
with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that ti,omap5-padconf is available, switch over to that compatible
property. Retain pinctrl-single for legacy support.
While at it, mark pinctrl as interrupt controller so that it can be
used with interrupts-extended property for wakeup events.
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds initial support. For now, regulators are always on and we
don't specify the input supply for all of the regulators.
Signed-off-by: huang lin <hl@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It's convenient (and less confusing to people reading logs) if the
eMMC port on rk3288 is consistenly marked with mmc0 and the sdmmc port
on rk3288 is consistently marked with mmc1. Add the appropriate
aliases.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds basic SPI nodes to the base rk3288 device tree file.
A few notes:
* It's assumed that most users of the SPI ports are using chip select
0. Thus the default pinctrl for the ports enables chip select 0
(but not chip select 1 on ports that have it). If a board wants to
use chip select 1 or wants a GPIO chip select the board should
override the pinctrl (just like boards can override UART pinctrl if
they have hardware flow control).
* Since SPI DMA support appears broken and the SPI works fine without
DMA we don't include the DMA references. That can come in a later
change.
Signed-off-by: huang lin <hl@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 has two kind of usb controller, this add the dwc2 controller
for otg and host1.
Controller can works with usb PHY default setting and Vbus on.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add regulator-name properties for the regulators that don't have them,
allowing the kernel to display the name from the schematic rather than
the name of the regulator on the PMIC in order to improve diagnostics.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T54 CoM can be used with various custom baseboards, other
than SB-T54 (supplied with SBC-T54 single board computer).
Update model property of SBC-T54 DT to clarify this.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RFBI node for OMAP DSS was left out when adding the rest of the DSS
nodes, because it was not clear how to set up the clocks for the RFBI.
However, it seems that if there is a HWMOD for a device, we also need a
DT node for it. Otherwise, at boot, we get:
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2542 _init+0x464/0x4e0()
omap_hwmod: dss_rfbi: doesn't have mpu register target base
Now that v3.17-rc3 contains a fix 8fd46439e1 ("ARM: dts:
omap54xx-clocks: Fix the l3 and l4 clock rates") for the L3 ICLK
required by the RFBI, let's add the RFBI node to get rid of the
warning.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated description per comments from Nishant]
Signed-off-by: Tony Lindgren <tony@atomide.com>
These baseboards are equipped with the Technexion TAO35030 SOM. So
they include this dtsi. The common parts are extracted into an "common"
dtsi file. The main difference between both boards is, that the *lcd
has DSS support enabled for the LCD.
Some HEAD acoustics specific features are:
- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the
basic support for it as an dtsi file which can be included by
baseboard equipped with this SOM. E.g. the Technexion Thunder
baseboard.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
